[ARM] JIVE: Add SPI bus definitions for LCD controller
Add the definitions for the VGG2432A4 intelligent
LCD display conneected via an GPIO-based SPI bus
on the Logitech Jive.
Signed-of-by: Ben Dooks <ben-linux@fluff.org>
diff --git a/arch/arm/mach-s3c2412/mach-jive.c b/arch/arm/mach-s3c2412/mach-jive.c
index b528ed9..ad6b942 100644
--- a/arch/arm/mach-s3c2412/mach-jive.c
+++ b/arch/arm/mach-s3c2412/mach-jive.c
@@ -20,6 +20,8 @@
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
@@ -34,6 +36,7 @@
#include <asm/arch/regs-gpio.h>
#include <asm/arch/regs-mem.h>
#include <asm/arch/regs-lcd.h>
+#include <asm/arch/spi-gpio.h>
#include <asm/arch/fb.h>
#include <asm/mach-types.h>
@@ -346,12 +349,48 @@
S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
};
+/* LCD SPI support */
+
+static void jive_lcd_spi_chipselect(struct s3c2410_spigpio_info *spi, int cs)
+{
+ s3c2410_gpio_setpin(S3C2410_GPB7, cs ? 0 : 1);
+}
+
+static struct s3c2410_spigpio_info jive_lcd_spi = {
+ .bus_num = 1,
+ .pin_clk = S3C2410_GPG8,
+ .pin_mosi = S3C2410_GPB8,
+ .chip_select = jive_lcd_spi_chipselect,
+};
+
+static struct platform_device jive_device_lcdspi = {
+ .name = "s3c24xx-spi-gpio",
+ .id = 1,
+ .num_resources = 0,
+ .dev.platform_data = &jive_lcd_spi,
+};
+
+/* JIVE SPI devices. */
+
+
+static struct spi_board_info __initdata jive_spi_devs[] = {
+ [0] = {
+ .modalias = "VGG2432A4",
+ .bus_num = 1,
+ .chip_select = 0,
+ .mode = SPI_MODE_3, /* CPOL=1, CPHA=1 */
+ .max_speed_hz = 100000,
+ },
+};
+
+
static struct platform_device *jive_devices[] __initdata = {
&s3c_device_usb,
&s3c_device_rtc,
&s3c_device_wdt,
&s3c_device_i2c,
&s3c_device_lcd,
+ &jive_device_lcdspi,
&s3c_device_nand,
&s3c_device_usbgadget,
};
@@ -502,6 +541,20 @@
s3c_device_nand.dev.platform_data = &jive_nand_info;
+ /* initialise the spi */
+
+ s3c2410_gpio_setpin(S3C2410_GPG13, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPG13, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPB7, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPB7, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPB6, 0);
+ s3c2410_gpio_cfgpin(S3C2410_GPB6, S3C2410_GPIO_OUTPUT);
+
+ s3c2410_gpio_setpin(S3C2410_GPG8, 1);
+ s3c2410_gpio_cfgpin(S3C2410_GPG8, S3C2410_GPIO_OUTPUT);
+
/* Turn off suspend on both USB ports, and switch the
* selectable USB port to USB device mode. */
@@ -512,6 +565,8 @@
s3c24xx_udc_set_platdata(&jive_udc_cfg);
s3c24xx_fb_set_platdata(&jive_lcd_config);
+ spi_register_board_info(jive_spi_devs, ARRAY_SIZE(jive_spi_devs));
+
platform_add_devices(jive_devices, ARRAY_SIZE(jive_devices));
}
