ARM: pxa: Push Colibri evalboard MFP into module files
This change -- pushing the MFP configuration back into Module files -- is
necessary because some evalboards can be used with multiple modules, where MFP
differs from module to module. Therefore MFP isn't board-specific, but
module-specific and the module should preconfigure itself for the board.
(And there is also the C preprocesor limitation and conflicting #define-s)
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
diff --git a/arch/arm/mach-pxa/colibri-pxa270.c b/arch/arm/mach-pxa/colibri-pxa270.c
index 73205bc..e940004 100644
--- a/arch/arm/mach-pxa/colibri-pxa270.c
+++ b/arch/arm/mach-pxa/colibri-pxa270.c
@@ -33,6 +33,99 @@
#include "generic.h"
/******************************************************************************
+ * Evaluation board MFP
+ ******************************************************************************/
+#ifdef CONFIG_MACH_COLIBRI_PXA270_EVALBOARD
+static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO0_GPIO, /* SD detect */
+
+ /* FFUART */
+ GPIO39_FFUART_TXD,
+ GPIO34_FFUART_RXD,
+
+ /* UHC */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+ GPIO119_USBH2_PWR,
+ GPIO120_USBH2_PEN,
+
+ /* PCMCIA */
+ GPIO85_nPCE_1,
+ GPIO54_nPCE_2,
+ GPIO55_nPREG,
+ GPIO50_nPIOR,
+ GPIO51_nPIOW,
+ GPIO49_nPWE,
+ GPIO48_nPOE,
+ GPIO57_nIOIS16,
+ GPIO56_nPWAIT,
+ GPIO104_PSKTSEL,
+ GPIO53_GPIO, /* RESET */
+ GPIO83_GPIO, /* BVD1 */
+ GPIO82_GPIO, /* BVD2 */
+ GPIO1_GPIO, /* READY */
+ GPIO84_GPIO, /* DETECT */
+ GPIO107_GPIO, /* PPEN */
+};
+#else
+static mfp_cfg_t colibri_pxa270_evalboard_pin_config[] __initdata = {};
+#endif
+
+#ifdef CONFIG_MACH_COLIBRI_PXA270_INCOME
+static mfp_cfg_t income_pin_config[] __initdata = {
+ /* MMC */
+ GPIO32_MMC_CLK,
+ GPIO92_MMC_DAT_0,
+ GPIO109_MMC_DAT_1,
+ GPIO110_MMC_DAT_2,
+ GPIO111_MMC_DAT_3,
+ GPIO112_MMC_CMD,
+ GPIO0_GPIO, /* SD detect */
+ GPIO1_GPIO, /* SD read-only */
+
+ /* FFUART */
+ GPIO39_FFUART_TXD,
+ GPIO34_FFUART_RXD,
+
+ /* BFUART */
+ GPIO42_BTUART_RXD,
+ GPIO43_BTUART_TXD,
+ GPIO45_BTUART_RTS,
+
+ /* STUART */
+ GPIO46_STUART_RXD,
+ GPIO47_STUART_TXD,
+
+ /* UHC */
+ GPIO88_USBH1_PWR,
+ GPIO89_USBH1_PEN,
+
+ /* LCD */
+ GPIOxx_LCD_TFT_16BPP,
+
+ /* PWM */
+ GPIO16_PWM0_OUT,
+
+ /* I2C */
+ GPIO117_I2C_SCL,
+ GPIO118_I2C_SDA,
+
+ /* LED */
+ GPIO54_GPIO, /* LED A */
+ GPIO55_GPIO, /* LED B */
+};
+#else
+static mfp_cfg_t income_pin_config[] __initdata = {};
+#endif
+
+/******************************************************************************
* Pin configuration
******************************************************************************/
static mfp_cfg_t colibri_pxa270_pin_config[] __initdata = {
@@ -185,9 +278,12 @@
switch (colibri_pxa270_baseboard) {
case COLIBRI_PXA270_EVALBOARD:
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(
+ colibri_pxa270_evalboard_pin_config));
colibri_pxa270_evalboard_init();
break;
case COLIBRI_PXA270_INCOME:
+ pxa2xx_mfp_config(ARRAY_AND_SIZE(income_pin_config));
colibri_pxa270_income_boardinit();
break;
default:
