blob: 02fc10d2d63bc28e064d918ea04af3115568600e [file] [log] [blame]
if ARCH_OMAP
menu "TI OMAP Common Features"
config ARCH_OMAP_OTG
bool
comment "OMAP Feature Selections"
config OMAP_DEBUG_DEVICES
bool
help
For debug cards on TI reference boards.
config OMAP_DEBUG_LEDS
def_bool y if NEW_LEDS
depends on OMAP_DEBUG_DEVICES
select LEDS_CLASS
config POWER_AVS_OMAP
bool "AVS(Adaptive Voltage Scaling) support for OMAP IP versions 1&2"
depends on POWER_AVS && (ARCH_OMAP3 || ARCH_OMAP4) && PM
select POWER_SUPPLY
help
Say Y to enable AVS(Adaptive Voltage Scaling)
support on OMAP containing the version 1 or
version 2 of the SmartReflex IP.
V1 is the 65nm version used in OMAP3430.
V2 is the update for the 45nm version of the IP used in OMAP3630
and OMAP4430
Please note, that by default SmartReflex is only
initialized and not enabled. To enable the automatic voltage
compensation for vdd mpu and vdd core from user space,
user must write 1 to
/debug/smartreflex/sr_<X>/autocomp,
where X is mpu_iva or core for OMAP3.
Optionally autocompensation can be enabled in the kernel
by default during system init via the enable_on_init flag
which an be passed as platform data to the smartreflex driver.
config POWER_AVS_OMAP_CLASS3
bool "Class 3 mode of Smartreflex Implementation"
depends on POWER_AVS_OMAP && TWL4030_CORE
help
Say Y to enable Class 3 implementation of Smartreflex
Class 3 implementation of Smartreflex employs continuous hardware
voltage calibration.
config OMAP_RESET_CLOCKS
bool "Reset unused clocks during boot"
depends on ARCH_OMAP
help
Say Y if you want to reset unused clocks during boot.
This option saves power, but assumes all drivers are
using the clock framework. Broken drivers that do not
yet use clock framework may not work with this option.
If you are booting from another operating system, you
probably do not want this option enabled until your
device drivers work properly.
config OMAP_MUX
bool "OMAP multiplexing support"
depends on ARCH_OMAP
default y
help
Pin multiplexing support for OMAP boards. If your bootloader
sets the multiplexing correctly, say N. Otherwise, or if unsure,
say Y.
config OMAP_MUX_DEBUG
bool "Multiplexing debug output"
depends on OMAP_MUX
help
Makes the multiplexing functions print out a lot of debug info.
This is useful if you want to find out the correct values of the
multiplexing registers.
config OMAP_MUX_WARNINGS
bool "Warn about pins the bootloader didn't set up"
depends on OMAP_MUX
default y
help
Choose Y here to warn whenever driver initialization logic needs
to change the pin multiplexing setup. When there are no warnings
printed, it's safe to deselect OMAP_MUX for your product.
config OMAP_MPU_TIMER
bool "Use mpu timer"
depends on ARCH_OMAP1
help
Select this option if you want to use the OMAP mpu timer. This
timer provides more intra-tick resolution than the 32KHz timer,
but consumes more power.
config OMAP_32K_TIMER
bool "Use 32KHz timer"
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
default y if (ARCH_OMAP16XX || ARCH_OMAP2PLUS)
help
Select this option if you want to enable the OMAP 32KHz timer.
This timer saves power compared to the OMAP_MPU_TIMER, and has
support for no tick during idle. The 32KHz timer provides less
intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
currently only available for OMAP16XX, 24XX, 34XX, OMAP4/5 and DRA7XX.
On OMAP2PLUS this value is only used for CONFIG_HZ and
CLOCK_TICK_RATE compile time calculation.
The actual timer selection is done in the board file
through the (DT_)MACHINE_START structure.
config OMAP3_L2_AUX_SECURE_SAVE_RESTORE
bool "OMAP3 HS/EMU save and restore for L2 AUX control register"
depends on ARCH_OMAP3 && PM
default n
help
Without this option, L2 Auxiliary control register contents are
lost during off-mode entry on HS/EMU devices. This feature
requires support from PPA / boot-loader in HS/EMU devices, which
currently does not exist by default.
config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
int "Service ID for the support routine to set L2 AUX control"
depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE
default 43
help
PPA routine service ID for setting L2 auxiliary control register.
config OMAP_DM_TIMER
bool "Use dual-mode timer"
depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
help
Select this option if you want to use OMAP Dual-Mode timers.
config OMAP_SERIAL_WAKE
bool "Enable wake-up events for serial ports"
depends on ARCH_OMAP1 && OMAP_MUX
default y
help
Select this option if you want to have your system wake up
to data on the serial RX line. This allows you to wake the
system from serial console.
choice
prompt "OMAP PM layer selection"
depends on ARCH_OMAP
default OMAP_PM_NOOP
config OMAP_PM_NOOP
bool "No-op/debug PM layer"
endchoice
endmenu
endif