diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index e7848a0..3e69c1c 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1948,8 +1948,12 @@
 				IRQ routing is enabled.
 		noacpi		[X86] Do not use ACPI for IRQ routing
 				or for PCI scanning.
-		use_crs		[X86] Use _CRS for PCI resource
-				allocation.
+		use_crs		[X86] Use PCI host bridge window information
+				from ACPI.  On BIOSes from 2008 or later, this
+				is enabled by default.  If you need to use this,
+				please report a bug.
+		nocrs		[X86] Ignore PCI host bridge windows from ACPI.
+			        If you need to use this, please report a bug.
 		routeirq	Do IRQ routing for all PCI devices.
 				This is normally done in pci_enable_device(),
 				so this option is a temporary workaround
@@ -1998,6 +2002,14 @@
 		force	Enable ASPM even on devices that claim not to support it.
 			WARNING: Forcing ASPM on may cause system lockups.
 
+	pcie_pme=	[PCIE,PM] Native PCIe PME signaling options:
+		off	Do not use native PCIe PME signaling.
+		force	Use native PCIe PME signaling even if the BIOS refuses
+			to allow the kernel to control the relevant PCIe config
+			registers.
+		nomsi	Do not use MSI for native PCIe PME signaling (this makes
+			all PCIe root ports use INTx for everything).
+
 	pcmv=		[HW,PCMCIA] BadgePAD 4
 
 	pd.		[PARIDE]
diff --git a/arch/alpha/kernel/pci.c b/arch/alpha/kernel/pci.c
index a91ba28..c9ab94e 100644
--- a/arch/alpha/kernel/pci.c
+++ b/arch/alpha/kernel/pci.c
@@ -126,8 +126,8 @@
 #define MB			(1024*KB)
 #define GB			(1024*MB)
 
-void
-pcibios_align_resource(void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
 		       resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
@@ -184,7 +184,7 @@
 		}
 	}
 
-	res->start = start;
+	return start;
 }
 #undef KB
 #undef MB
diff --git a/arch/arm/kernel/bios32.c b/arch/arm/kernel/bios32.c
index 8096819..bd397e0 100644
--- a/arch/arm/kernel/bios32.c
+++ b/arch/arm/kernel/bios32.c
@@ -616,15 +616,17 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might be mirrored at 0x0100-0x03ff..
  */
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
 	resource_size_t start = res->start;
 
 	if (res->flags & IORESOURCE_IO && start & 0x300)
 		start = (start + 0x3ff) & ~0x3ff;
 
-	res->start = (start + align - 1) & ~(align - 1);
+	start = (start + align - 1) & ~(align - 1);
+
+	return start;
 }
 
 /**
diff --git a/arch/cris/arch-v32/drivers/pci/bios.c b/arch/cris/arch-v32/drivers/pci/bios.c
index 77ee319..d4b9c36 100644
--- a/arch/cris/arch-v32/drivers/pci/bios.c
+++ b/arch/cris/arch-v32/drivers/pci/bios.c
@@ -41,18 +41,16 @@
 	return 0;
 }
 
-void
-pcibios_align_resource(void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
 		       resource_size_t size, resource_size_t align)
 {
-	if (res->flags & IORESOURCE_IO) {
-		resource_size_t start = res->start;
+	resource_size_t start = res->start;
 
-		if (start & 0x300) {
-			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
-	}
+	if ((res->flags & IORESOURCE_IO) && (start & 0x300))
+		start = (start + 0x3ff) & ~0x3ff;
+
+	return start
 }
 
 int pcibios_enable_resources(struct pci_dev *dev, int mask)
diff --git a/arch/frv/mb93090-mb00/pci-frv.c b/arch/frv/mb93090-mb00/pci-frv.c
index 566bdeb..1ed15d7 100644
--- a/arch/frv/mb93090-mb00/pci-frv.c
+++ b/arch/frv/mb93090-mb00/pci-frv.c
@@ -32,18 +32,16 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void
-pcibios_align_resource(void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
 		       resource_size_t size, resource_size_t align)
 {
-	if (res->flags & IORESOURCE_IO) {
-		resource_size_t start = res->start;
+	resource_size_t start = res->start;
 
-		if (start & 0x300) {
-			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
-	}
+	if ((res->flags & IORESOURCE_IO) && (start & 0x300))
+		start = (start + 0x3ff) & ~0x3ff;
+
+	return start
 }
 
 
diff --git a/arch/ia64/include/asm/acpi.h b/arch/ia64/include/asm/acpi.h
index e97b255..93997bd 100644
--- a/arch/ia64/include/asm/acpi.h
+++ b/arch/ia64/include/asm/acpi.h
@@ -98,6 +98,7 @@
 #endif
 #define acpi_processor_cstate_check(x) (x) /* no idle limits on IA64 :) */
 static inline void disable_acpi(void) { }
+static inline void pci_acpi_crs_quirks(void) { }
 
 const char *acpi_get_sysname (void);
 int acpi_request_vector (u32 int_type);
diff --git a/arch/ia64/pci/pci.c b/arch/ia64/pci/pci.c
index df639db7..64aff52 100644
--- a/arch/ia64/pci/pci.c
+++ b/arch/ia64/pci/pci.c
@@ -320,9 +320,9 @@
 static void __devinit
 pcibios_setup_root_windows(struct pci_bus *bus, struct pci_controller *ctrl)
 {
-	int i, j;
+	int i;
 
-	j = 0;
+	pci_bus_remove_resources(bus);
 	for (i = 0; i < ctrl->windows; i++) {
 		struct resource *res = &ctrl->window[i].resource;
 		/* HP's firmware has a hack to work around a Windows bug.
@@ -330,13 +330,7 @@
 		if ((res->flags & IORESOURCE_MEM) &&
 		    (res->end - res->start < 16))
 			continue;
-		if (j >= PCI_BUS_NUM_RESOURCES) {
-			dev_warn(&bus->dev,
-				 "ignoring host bridge window %pR (no space)\n",
-				 res);
-			continue;
-		}
-		bus->resource[j++] = res;
+		pci_bus_add_resource(bus, res, 0);
 	}
 }
 
@@ -452,13 +446,12 @@
 static int __devinit is_valid_resource(struct pci_dev *dev, int idx)
 {
 	unsigned int i, type_mask = IORESOURCE_IO | IORESOURCE_MEM;
-	struct resource *devr = &dev->resource[idx];
+	struct resource *devr = &dev->resource[idx], *busr;
 
 	if (!dev->bus)
 		return 0;
-	for (i=0; i<PCI_BUS_NUM_RESOURCES; i++) {
-		struct resource *busr = dev->bus->resource[i];
 
+	pci_bus_for_each_resource(dev->bus, busr, i) {
 		if (!busr || ((busr->flags ^ devr->flags) & type_mask))
 			continue;
 		if ((devr->start) && (devr->start >= busr->start) &&
@@ -547,10 +540,11 @@
 		acpi_pci_irq_disable(dev);
 }
 
-void
-pcibios_align_resource (void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource (void *data, const struct resource *res,
 		        resource_size_t size, resource_size_t align)
 {
+	return res->start;
 }
 
 /*
diff --git a/arch/mips/pci/pci.c b/arch/mips/pci/pci.c
index 9a11c22..f87f5e1 100644
--- a/arch/mips/pci/pci.c
+++ b/arch/mips/pci/pci.c
@@ -49,8 +49,8 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void
-pcibios_align_resource(void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
 		       resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
@@ -73,7 +73,7 @@
 			start = PCIBIOS_MIN_MEM + hose->mem_resource->start;
 	}
 
-	res->start = start;
+	return start;
 }
 
 static void __devinit pcibios_scanbus(struct pci_controller *hose)
diff --git a/arch/mips/pmc-sierra/yosemite/ht.c b/arch/mips/pmc-sierra/yosemite/ht.c
index 678388f..fd22597 100644
--- a/arch/mips/pmc-sierra/yosemite/ht.c
+++ b/arch/mips/pmc-sierra/yosemite/ht.c
@@ -345,14 +345,13 @@
         return pcibios_enable_resources(dev);
 }
 
-void pcibios_align_resource(void *data, struct resource *res,
-                            resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
         struct pci_dev *dev = data;
+	resource_size_t start = res->start;
 
         if (res->flags & IORESOURCE_IO) {
-                resource_size_t start = res->start;
-
                 /* We need to avoid collisions with `mirrored' VGA ports
                    and other strange ISA hardware, so we always want the
                    addresses kilobyte aligned.  */
@@ -363,8 +362,9 @@
                 }
 
                 start = (start + 1024 - 1) & ~(1024 - 1);
-                res->start = start;
         }
+
+	return start;
 }
 
 struct pci_ops titan_pci_ops = {
diff --git a/arch/mn10300/unit-asb2305/pci-asb2305.c b/arch/mn10300/unit-asb2305/pci-asb2305.c
index 78cd134..d6119b8 100644
--- a/arch/mn10300/unit-asb2305/pci-asb2305.c
+++ b/arch/mn10300/unit-asb2305/pci-asb2305.c
@@ -31,9 +31,11 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
+	resource_size_t start = res->start;
+
 #if 0
 	struct pci_dev *dev = data;
 
@@ -47,14 +49,10 @@
 	       );
 #endif
 
-	if (res->flags & IORESOURCE_IO) {
-		unsigned long start = res->start;
+	if ((res->flags & IORESOURCE_IO) && (start & 0x300))
+		start = (start + 0x3ff) & ~0x3ff;
 
-		if (start & 0x300) {
-			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
-	}
+	return start;
 }
 
 
diff --git a/arch/mn10300/unit-asb2305/pci.c b/arch/mn10300/unit-asb2305/pci.c
index 2cb7e75..6d8720a 100644
--- a/arch/mn10300/unit-asb2305/pci.c
+++ b/arch/mn10300/unit-asb2305/pci.c
@@ -331,12 +331,10 @@
 static int __devinit is_valid_resource(struct pci_dev *dev, int idx)
 {
 	unsigned int i, type_mask = IORESOURCE_IO | IORESOURCE_MEM;
-	struct resource *devr = &dev->resource[idx];
+	struct resource *devr = &dev->resource[idx], *busr;
 
 	if (dev->bus) {
-		for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-			struct resource *busr = dev->bus->resource[i];
-
+		pci_bus_for_each_resource(dev->bus, busr, i) {
 			if (!busr || (busr->flags ^ devr->flags) & type_mask)
 				continue;
 
diff --git a/arch/parisc/kernel/pci.c b/arch/parisc/kernel/pci.c
index 9e74bfe..38372e7 100644
--- a/arch/parisc/kernel/pci.c
+++ b/arch/parisc/kernel/pci.c
@@ -257,10 +257,10 @@
  * Since we are just checking candidates, don't use any fields other
  * than res->start.
  */
-void pcibios_align_resource(void *data, struct resource *res,
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
 				resource_size_t size, resource_size_t alignment)
 {
-	resource_size_t mask, align;
+	resource_size_t mask, align, start = res->start;
 
 	DBG_RES("pcibios_align_resource(%s, (%p) [%lx,%lx]/%x, 0x%lx, 0x%lx)\n",
 		pci_name(((struct pci_dev *) data)),
@@ -272,10 +272,10 @@
 
 	/* Align to largest of MIN or input size */
 	mask = max(alignment, align) - 1;
-	res->start += mask;
-	res->start &= ~mask;
+	start += mask;
+	start &= ~mask;
 
-	/* The caller updates the end field, we don't.  */
+	return start;
 }
 
 
diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c
index cadbed6..2597f95 100644
--- a/arch/powerpc/kernel/pci-common.c
+++ b/arch/powerpc/kernel/pci-common.c
@@ -1047,10 +1047,8 @@
 
 	struct pci_dev *dev = bus->self;
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; ++i) {
-		if ((res = bus->resource[i]) == NULL)
-			continue;
-		if (!res->flags)
+	pci_bus_for_each_resource(bus, res, i) {
+		if (!res || !res->flags)
 			continue;
 		if (i >= 3 && bus->self->transparent)
 			continue;
@@ -1181,21 +1179,20 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void pcibios_align_resource(void *data, struct resource *res,
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
 				resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
+	resource_size_t start = res->start;
 
 	if (res->flags & IORESOURCE_IO) {
-		resource_size_t start = res->start;
-
 		if (skip_isa_ioresource_align(dev))
-			return;
-		if (start & 0x300) {
+			return start;
+		if (start & 0x300)
 			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
 	}
+
+	return start;
 }
 EXPORT_SYMBOL(pcibios_align_resource);
 
@@ -1278,9 +1275,8 @@
 	pr_debug("PCI: Allocating bus resources for %04x:%02x...\n",
 		 pci_domain_nr(bus), bus->number);
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; ++i) {
-		if ((res = bus->resource[i]) == NULL || !res->flags
-		    || res->start > res->end || res->parent)
+	pci_bus_for_each_resource(bus, res, i) {
+		if (!res || !res->flags || res->start > res->end || res->parent)
 			continue;
 		if (bus->parent == NULL)
 			pr = (res->flags & IORESOURCE_IO) ?
diff --git a/arch/powerpc/platforms/fsl_uli1575.c b/arch/powerpc/platforms/fsl_uli1575.c
index fd23a1d..8b0c208 100644
--- a/arch/powerpc/platforms/fsl_uli1575.c
+++ b/arch/powerpc/platforms/fsl_uli1575.c
@@ -222,6 +222,7 @@
 	int i;
 	u8 *dummy;
 	struct pci_bus *bus = dev->bus;
+	struct resource *res;
 	resource_size_t end = 0;
 
 	for (i = PCI_BRIDGE_RESOURCES; i < PCI_BRIDGE_RESOURCES+3; i++) {
@@ -230,13 +231,12 @@
 			end = pci_resource_end(dev, i);
 	}
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		if ((bus->resource[i]) &&
-			(bus->resource[i]->flags & IORESOURCE_MEM)) {
-			if (bus->resource[i]->end == end)
-				dummy = ioremap(bus->resource[i]->start, 0x4);
+	pci_bus_for_each_resource(bus, res, i) {
+		if (res && res->flags & IORESOURCE_MEM) {
+			if (res->end == end)
+				dummy = ioremap(res->start, 0x4);
 			else
-				dummy = ioremap(bus->resource[i]->end - 3, 0x4);
+				dummy = ioremap(res->end - 3, 0x4);
 			if (dummy) {
 				in_8(dummy);
 				iounmap(dummy);
diff --git a/arch/sh/drivers/pci/pci.c b/arch/sh/drivers/pci/pci.c
index c481df6..96213fd 100644
--- a/arch/sh/drivers/pci/pci.c
+++ b/arch/sh/drivers/pci/pci.c
@@ -148,8 +148,8 @@
  * addresses to be allocated in the 0x000-0x0ff region
  * modulo 0x400.
  */
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
 	struct pci_channel *chan = dev->sysdata;
@@ -171,7 +171,7 @@
 			start = PCIBIOS_MIN_MEM + chan->mem_resource->start;
 	}
 
-	res->start = start;
+	return start;
 }
 
 void pcibios_resource_to_bus(struct pci_dev *dev, struct pci_bus_region *region,
diff --git a/arch/sparc/kernel/pci.c b/arch/sparc/kernel/pci.c
index 592b03d..37b66c6 100644
--- a/arch/sparc/kernel/pci.c
+++ b/arch/sparc/kernel/pci.c
@@ -722,9 +722,10 @@
 {
 }
 
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
+	return res->start;
 }
 
 int pcibios_enable_device(struct pci_dev *dev, int mask)
diff --git a/arch/sparc/kernel/pcic.c b/arch/sparc/kernel/pcic.c
index 4e2724e..75e88c00 100644
--- a/arch/sparc/kernel/pcic.c
+++ b/arch/sparc/kernel/pcic.c
@@ -768,9 +768,10 @@
 	return str;
 }
 
-void pcibios_align_resource(void *data, struct resource *res,
-			    resource_size_t size, resource_size_t align)
+resource_size_t pcibios_align_resource(void *data, const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
+	return res->start;
 }
 
 int pcibios_enable_device(struct pci_dev *pdev, int mask)
diff --git a/arch/x86/include/asm/pci_x86.h b/arch/x86/include/asm/pci_x86.h
index b4bf9a9..05b58cc 100644
--- a/arch/x86/include/asm/pci_x86.h
+++ b/arch/x86/include/asm/pci_x86.h
@@ -29,6 +29,7 @@
 #define PCI_CHECK_ENABLE_AMD_MMCONF	0x20000
 #define PCI_HAS_IO_ECS		0x40000
 #define PCI_NOASSIGN_ROMS	0x80000
+#define PCI_ROOT_NO_CRS		0x100000
 
 extern unsigned int pci_probe;
 extern unsigned long pirq_table_addr;
diff --git a/arch/x86/pci/acpi.c b/arch/x86/pci/acpi.c
index 959e548..5f11ff6 100644
--- a/arch/x86/pci/acpi.c
+++ b/arch/x86/pci/acpi.c
@@ -15,6 +15,51 @@
 	int busnum;
 };
 
+static bool pci_use_crs = true;
+
+static int __init set_use_crs(const struct dmi_system_id *id)
+{
+	pci_use_crs = true;
+	return 0;
+}
+
+static const struct dmi_system_id pci_use_crs_table[] __initconst = {
+	/* http://bugzilla.kernel.org/show_bug.cgi?id=14183 */
+	{
+		.callback = set_use_crs,
+		.ident = "IBM System x3800",
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "IBM"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "x3800"),
+		},
+	},
+	{}
+};
+
+void __init pci_acpi_crs_quirks(void)
+{
+	int year;
+
+	if (dmi_get_date(DMI_BIOS_DATE, &year, NULL, NULL) && year < 2008)
+		pci_use_crs = false;
+
+	dmi_check_system(pci_use_crs_table);
+
+	/*
+	 * If the user specifies "pci=use_crs" or "pci=nocrs" explicitly, that
+	 * takes precedence over anything we figured out above.
+	 */
+	if (pci_probe & PCI_ROOT_NO_CRS)
+		pci_use_crs = false;
+	else if (pci_probe & PCI_USE__CRS)
+		pci_use_crs = true;
+
+	printk(KERN_INFO "PCI: %s host bridge windows from ACPI; "
+	       "if necessary, use \"pci=%s\" and report a bug\n",
+	       pci_use_crs ? "Using" : "Ignoring",
+	       pci_use_crs ? "nocrs" : "use_crs");
+}
+
 static acpi_status
 resource_to_addr(struct acpi_resource *resource,
 			struct acpi_resource_address64 *addr)
@@ -45,20 +90,6 @@
 	return AE_OK;
 }
 
-static int
-bus_has_transparent_bridge(struct pci_bus *bus)
-{
-	struct pci_dev *dev;
-
-	list_for_each_entry(dev, &bus->devices, bus_list) {
-		u16 class = dev->class >> 8;
-
-		if (class == PCI_CLASS_BRIDGE_PCI && dev->transparent)
-			return true;
-	}
-	return false;
-}
-
 static void
 align_resource(struct acpi_device *bridge, struct resource *res)
 {
@@ -92,12 +123,8 @@
 	acpi_status status;
 	unsigned long flags;
 	struct resource *root;
-	int max_root_bus_resources = PCI_BUS_NUM_RESOURCES;
 	u64 start, end;
 
-	if (bus_has_transparent_bridge(info->bus))
-		max_root_bus_resources -= 3;
-
 	status = resource_to_addr(acpi_res, &addr);
 	if (!ACPI_SUCCESS(status))
 		return AE_OK;
@@ -115,15 +142,6 @@
 
 	start = addr.minimum + addr.translation_offset;
 	end = start + addr.address_length - 1;
-	if (info->res_num >= max_root_bus_resources) {
-		if (pci_probe & PCI_USE__CRS)
-			printk(KERN_WARNING "PCI: Failed to allocate "
-			       "0x%lx-0x%lx from %s for %s due to _CRS "
-			       "returning more than %d resource descriptors\n",
-			       (unsigned long) start, (unsigned long) end,
-			       root->name, info->name, max_root_bus_resources);
-		return AE_OK;
-	}
 
 	res = &info->res[info->res_num];
 	res->name = info->name;
@@ -133,7 +151,7 @@
 	res->child = NULL;
 	align_resource(info->bridge, res);
 
-	if (!(pci_probe & PCI_USE__CRS)) {
+	if (!pci_use_crs) {
 		dev_printk(KERN_DEBUG, &info->bridge->dev,
 			   "host bridge window %pR (ignored)\n", res);
 		return AE_OK;
@@ -143,7 +161,7 @@
 		dev_err(&info->bridge->dev,
 			"can't allocate host bridge window %pR\n", res);
 	} else {
-		info->bus->resource[info->res_num] = res;
+		pci_bus_add_resource(info->bus, res, 0);
 		info->res_num++;
 		if (addr.translation_offset)
 			dev_info(&info->bridge->dev, "host bridge window %pR "
@@ -164,10 +182,8 @@
 	struct pci_root_info info;
 	size_t size;
 
-	if (!(pci_probe & PCI_USE__CRS))
-		dev_info(&device->dev,
-			 "ignoring host bridge windows from ACPI; "
-			 "boot with \"pci=use_crs\" to use them\n");
+	if (pci_use_crs)
+		pci_bus_remove_resources(bus);
 
 	info.bridge = device;
 	info.bus = bus;
diff --git a/arch/x86/pci/bus_numa.c b/arch/x86/pci/bus_numa.c
index f939d60..12d54ff 100644
--- a/arch/x86/pci/bus_numa.c
+++ b/arch/x86/pci/bus_numa.c
@@ -36,13 +36,14 @@
 	printk(KERN_DEBUG "PCI: peer root bus %02x res updated from pci conf\n",
 			b->number);
 
+	pci_bus_remove_resources(b);
 	info = &pci_root_info[i];
 	for (j = 0; j < info->res_num; j++) {
 		struct resource *res;
 		struct resource *root;
 
 		res = &info->res[j];
-		b->resource[j] = res;
+		pci_bus_add_resource(b, res, 0);
 		if (res->flags & IORESOURCE_IO)
 			root = &ioport_resource;
 		else
diff --git a/arch/x86/pci/bus_numa.h b/arch/x86/pci/bus_numa.h
index adbc23f..731b64e 100644
--- a/arch/x86/pci/bus_numa.h
+++ b/arch/x86/pci/bus_numa.h
@@ -2,8 +2,7 @@
 
 /*
  * sub bus (transparent) will use entres from 3 to store extra from
- * root, so need to make sure we have enough slot there, Should we
- * increase PCI_BUS_NUM_RESOURCES?
+ * root, so need to make sure we have enough slot there.
  */
 #define RES_NUM 16
 struct pci_root_info {
diff --git a/arch/x86/pci/common.c b/arch/x86/pci/common.c
index d2552c6..3736176 100644
--- a/arch/x86/pci/common.c
+++ b/arch/x86/pci/common.c
@@ -520,6 +520,9 @@
 	} else if (!strcmp(str, "use_crs")) {
 		pci_probe |= PCI_USE__CRS;
 		return NULL;
+	} else if (!strcmp(str, "nocrs")) {
+		pci_probe |= PCI_ROOT_NO_CRS;
+		return NULL;
 	} else if (!strcmp(str, "earlydump")) {
 		pci_early_dump_regs = 1;
 		return NULL;
diff --git a/arch/x86/pci/i386.c b/arch/x86/pci/i386.c
index 5dc9e8c..5a8fbf8 100644
--- a/arch/x86/pci/i386.c
+++ b/arch/x86/pci/i386.c
@@ -60,22 +60,20 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void
-pcibios_align_resource(void *data, struct resource *res,
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
 			resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
+	resource_size_t start = res->start;
 
 	if (res->flags & IORESOURCE_IO) {
-		resource_size_t start = res->start;
-
 		if (skip_isa_ioresource_align(dev))
-			return;
-		if (start & 0x300) {
+			return start;
+		if (start & 0x300)
 			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
 	}
+	return start;
 }
 EXPORT_SYMBOL(pcibios_align_resource);
 
diff --git a/arch/x86/pci/irq.c b/arch/x86/pci/irq.c
index 0696d50..b02f6d8 100644
--- a/arch/x86/pci/irq.c
+++ b/arch/x86/pci/irq.c
@@ -590,6 +590,8 @@
 	case PCI_DEVICE_ID_INTEL_ICH10_1:
 	case PCI_DEVICE_ID_INTEL_ICH10_2:
 	case PCI_DEVICE_ID_INTEL_ICH10_3:
+	case PCI_DEVICE_ID_INTEL_CPT_LPC1:
+	case PCI_DEVICE_ID_INTEL_CPT_LPC2:
 		r->name = "PIIX/ICH";
 		r->get = pirq_piix_get;
 		r->set = pirq_piix_set;
diff --git a/arch/x86/pci/mmconfig-shared.c b/arch/x86/pci/mmconfig-shared.c
index b19d1e5..8f3f9a5 100644
--- a/arch/x86/pci/mmconfig-shared.c
+++ b/arch/x86/pci/mmconfig-shared.c
@@ -303,22 +303,17 @@
 {
 	struct pci_mmcfg_region *cfg, *cfgx;
 
-	/* last one*/
-	cfg = list_entry(pci_mmcfg_list.prev, typeof(*cfg), list);
-	if (cfg)
-		if (cfg->end_bus < cfg->start_bus)
-			cfg->end_bus = 255;
-
-	if (list_is_singular(&pci_mmcfg_list))
-		return;
-
-	/* don't overlap please */
+	/* Fixup overlaps */
 	list_for_each_entry(cfg, &pci_mmcfg_list, list) {
 		if (cfg->end_bus < cfg->start_bus)
 			cfg->end_bus = 255;
 
+		/* Don't access the list head ! */
+		if (cfg->list.next == &pci_mmcfg_list)
+			break;
+
 		cfgx = list_entry(cfg->list.next, typeof(*cfg), list);
-		if (cfg != cfgx && cfg->end_bus >= cfgx->start_bus)
+		if (cfg->end_bus >= cfgx->start_bus)
 			cfg->end_bus = cfgx->start_bus - 1;
 	}
 }
diff --git a/arch/xtensa/kernel/pci.c b/arch/xtensa/kernel/pci.c
index b7c0734..cd10269 100644
--- a/arch/xtensa/kernel/pci.c
+++ b/arch/xtensa/kernel/pci.c
@@ -69,26 +69,25 @@
  * but we want to try to avoid allocating at 0x2900-0x2bff
  * which might have be mirrored at 0x0100-0x03ff..
  */
-void
-pcibios_align_resource(void *data, struct resource *res, resource_size_t size,
-    		       resource_size_t align)
+resource_size_t
+pcibios_align_resource(void *data, const struct resource *res,
+		       resource_size_t size, resource_size_t align)
 {
 	struct pci_dev *dev = data;
+	resource_size_t start = res->start;
 
 	if (res->flags & IORESOURCE_IO) {
-		resource_size_t start = res->start;
-
 		if (size > 0x100) {
 			printk(KERN_ERR "PCI: I/O Region %s/%d too large"
 			       " (%ld bytes)\n", pci_name(dev),
 			       dev->resource - res, size);
 		}
 
-		if (start & 0x300) {
+		if (start & 0x300)
 			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
-		}
 	}
+
+	return start;
 }
 
 int
diff --git a/drivers/acpi/acpica/acevents.h b/drivers/acpi/acpica/acevents.h
index 0bba148..4ced54f 100644
--- a/drivers/acpi/acpica/acevents.h
+++ b/drivers/acpi/acpica/acevents.h
@@ -76,12 +76,9 @@
  * evgpe - GPE handling and dispatch
  */
 acpi_status
-acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info,
-				u8 type);
+acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info);
 
-acpi_status
-acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info,
-		   u8 write_to_hardware);
+acpi_status acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info);
 
 acpi_status acpi_ev_disable_gpe(struct acpi_gpe_event_info *gpe_event_info);
 
@@ -122,9 +119,6 @@
 u32 acpi_ev_gpe_detect(struct acpi_gpe_xrupt_info *gpe_xrupt_list);
 
 acpi_status
-acpi_ev_set_gpe_type(struct acpi_gpe_event_info *gpe_event_info, u8 type);
-
-acpi_status
 acpi_ev_check_for_wake_only_gpe(struct acpi_gpe_event_info *gpe_event_info);
 
 acpi_status acpi_ev_gpe_initialize(void);
diff --git a/drivers/acpi/acpica/aclocal.h b/drivers/acpi/acpica/aclocal.h
index 81e64f4..13cb80c 100644
--- a/drivers/acpi/acpica/aclocal.h
+++ b/drivers/acpi/acpica/aclocal.h
@@ -426,6 +426,8 @@
 	struct acpi_gpe_register_info *register_info;	/* Backpointer to register info */
 	u8 flags;		/* Misc info about this GPE */
 	u8 gpe_number;		/* This GPE */
+	u8 runtime_count;
+	u8 wakeup_count;
 };
 
 /* Information about a GPE register pair, one per each status/enable pair in an array */
diff --git a/drivers/acpi/acpica/acobject.h b/drivers/acpi/acpica/acobject.h
index 64062b1..07f6e2e 100644
--- a/drivers/acpi/acpica/acobject.h
+++ b/drivers/acpi/acpica/acobject.h
@@ -287,8 +287,10 @@
 
 struct acpi_object_notify_handler {
 	ACPI_OBJECT_COMMON_HEADER struct acpi_namespace_node *node;	/* Parent device */
+	u32 handler_type;
 	acpi_notify_handler handler;
 	void *context;
+	struct acpi_object_notify_handler *next;
 };
 
 struct acpi_object_addr_handler {
diff --git a/drivers/acpi/acpica/evgpe.c b/drivers/acpi/acpica/evgpe.c
index afacf44..0b45346 100644
--- a/drivers/acpi/acpica/evgpe.c
+++ b/drivers/acpi/acpica/evgpe.c
@@ -54,54 +54,9 @@
 
 /*******************************************************************************
  *
- * FUNCTION:    acpi_ev_set_gpe_type
- *
- * PARAMETERS:  gpe_event_info          - GPE to set
- *              Type                    - New type
- *
- * RETURN:      Status
- *
- * DESCRIPTION: Sets the new type for the GPE (wake, run, or wake/run)
- *
- ******************************************************************************/
-
-acpi_status
-acpi_ev_set_gpe_type(struct acpi_gpe_event_info *gpe_event_info, u8 type)
-{
-	acpi_status status;
-
-	ACPI_FUNCTION_TRACE(ev_set_gpe_type);
-
-	/* Validate type and update register enable masks */
-
-	switch (type) {
-	case ACPI_GPE_TYPE_WAKE:
-	case ACPI_GPE_TYPE_RUNTIME:
-	case ACPI_GPE_TYPE_WAKE_RUN:
-		break;
-
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
-	}
-
-	/* Disable the GPE if currently enabled */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-
-	/* Clear the type bits and insert the new Type */
-
-	gpe_event_info->flags &= ~ACPI_GPE_TYPE_MASK;
-	gpe_event_info->flags |= type;
-	return_ACPI_STATUS(status);
-}
-
-/*******************************************************************************
- *
  * FUNCTION:    acpi_ev_update_gpe_enable_masks
  *
  * PARAMETERS:  gpe_event_info          - GPE to update
- *              Type                    - What to do: ACPI_GPE_DISABLE or
- *                                        ACPI_GPE_ENABLE
  *
  * RETURN:      Status
  *
@@ -110,8 +65,7 @@
  ******************************************************************************/
 
 acpi_status
-acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info,
-				u8 type)
+acpi_ev_update_gpe_enable_masks(struct acpi_gpe_event_info *gpe_event_info)
 {
 	struct acpi_gpe_register_info *gpe_register_info;
 	u8 register_bit;
@@ -127,37 +81,14 @@
 	    (1 <<
 	     (gpe_event_info->gpe_number - gpe_register_info->base_gpe_number));
 
-	/* 1) Disable case. Simply clear all enable bits */
+	ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake, register_bit);
+	ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
 
-	if (type == ACPI_GPE_DISABLE) {
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake,
-			       register_bit);
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
-		return_ACPI_STATUS(AE_OK);
-	}
-
-	/* 2) Enable case. Set/Clear the appropriate enable bits */
-
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
-		ACPI_SET_BIT(gpe_register_info->enable_for_wake, register_bit);
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
-
-	case ACPI_GPE_TYPE_RUNTIME:
-		ACPI_CLEAR_BIT(gpe_register_info->enable_for_wake,
-			       register_bit);
+	if (gpe_event_info->runtime_count)
 		ACPI_SET_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
 
-	case ACPI_GPE_TYPE_WAKE_RUN:
+	if (gpe_event_info->wakeup_count)
 		ACPI_SET_BIT(gpe_register_info->enable_for_wake, register_bit);
-		ACPI_SET_BIT(gpe_register_info->enable_for_run, register_bit);
-		break;
-
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
-	}
 
 	return_ACPI_STATUS(AE_OK);
 }
@@ -167,8 +98,6 @@
  * FUNCTION:    acpi_ev_enable_gpe
  *
  * PARAMETERS:  gpe_event_info          - GPE to enable
- *              write_to_hardware       - Enable now, or just mark data structs
- *                                        (WAKE GPEs should be deferred)
  *
  * RETURN:      Status
  *
@@ -176,9 +105,7 @@
  *
  ******************************************************************************/
 
-acpi_status
-acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info,
-		   u8 write_to_hardware)
+acpi_status acpi_ev_enable_gpe(struct acpi_gpe_event_info *gpe_event_info)
 {
 	acpi_status status;
 
@@ -186,47 +113,20 @@
 
 	/* Make sure HW enable masks are updated */
 
-	status =
-	    acpi_ev_update_gpe_enable_masks(gpe_event_info, ACPI_GPE_ENABLE);
-	if (ACPI_FAILURE(status)) {
+	status = acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	if (ACPI_FAILURE(status))
 		return_ACPI_STATUS(status);
-	}
 
 	/* Mark wake-enabled or HW enable, or both */
 
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
+	if (gpe_event_info->runtime_count) {
+		/* Clear the GPE (of stale events), then enable it */
+		status = acpi_hw_clear_gpe(gpe_event_info);
+		if (ACPI_FAILURE(status))
+			return_ACPI_STATUS(status);
 
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-		break;
-
-	case ACPI_GPE_TYPE_WAKE_RUN:
-
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-
-		/*lint -fallthrough */
-
-	case ACPI_GPE_TYPE_RUNTIME:
-
-		ACPI_SET_BIT(gpe_event_info->flags, ACPI_GPE_RUN_ENABLED);
-
-		if (write_to_hardware) {
-
-			/* Clear the GPE (of stale events), then enable it */
-
-			status = acpi_hw_clear_gpe(gpe_event_info);
-			if (ACPI_FAILURE(status)) {
-				return_ACPI_STATUS(status);
-			}
-
-			/* Enable the requested runtime GPE */
-
-			status = acpi_hw_write_gpe_enable_reg(gpe_event_info);
-		}
-		break;
-
-	default:
-		return_ACPI_STATUS(AE_BAD_PARAMETER);
+		/* Enable the requested runtime GPE */
+		status = acpi_hw_write_gpe_enable_reg(gpe_event_info);
 	}
 
 	return_ACPI_STATUS(AE_OK);
@@ -252,34 +152,9 @@
 
 	/* Make sure HW enable masks are updated */
 
-	status =
-	    acpi_ev_update_gpe_enable_masks(gpe_event_info, ACPI_GPE_DISABLE);
-	if (ACPI_FAILURE(status)) {
+	status = acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	if (ACPI_FAILURE(status))
 		return_ACPI_STATUS(status);
-	}
-
-	/* Clear the appropriate enabled flags for this GPE */
-
-	switch (gpe_event_info->flags & ACPI_GPE_TYPE_MASK) {
-	case ACPI_GPE_TYPE_WAKE:
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-		break;
-
-	case ACPI_GPE_TYPE_WAKE_RUN:
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_WAKE_ENABLED);
-
-		/* fallthrough */
-
-	case ACPI_GPE_TYPE_RUNTIME:
-
-		/* Disable the requested runtime GPE */
-
-		ACPI_CLEAR_BIT(gpe_event_info->flags, ACPI_GPE_RUN_ENABLED);
-		break;
-
-	default:
-		break;
-	}
 
 	/*
 	 * Even if we don't know the GPE type, make sure that we always
@@ -521,7 +396,7 @@
 
 	/* Set the GPE flags for return to enabled state */
 
-	(void)acpi_ev_enable_gpe(gpe_event_info, FALSE);
+	(void)acpi_ev_update_gpe_enable_masks(gpe_event_info);
 
 	/*
 	 * Take a snapshot of the GPE info for this level - we copy the info to
diff --git a/drivers/acpi/acpica/evgpeblk.c b/drivers/acpi/acpica/evgpeblk.c
index 2479209..3d4c4ac 100644
--- a/drivers/acpi/acpica/evgpeblk.c
+++ b/drivers/acpi/acpica/evgpeblk.c
@@ -258,7 +258,6 @@
 	u32 gpe_number;
 	char name[ACPI_NAME_SIZE + 1];
 	u8 type;
-	acpi_status status;
 
 	ACPI_FUNCTION_TRACE(ev_save_method_info);
 
@@ -325,26 +324,20 @@
 
 	/*
 	 * Now we can add this information to the gpe_event_info block for use
-	 * during dispatch of this GPE. Default type is RUNTIME, although this may
-	 * change when the _PRW methods are executed later.
+	 * during dispatch of this GPE.
 	 */
 	gpe_event_info =
 	    &gpe_block->event_info[gpe_number - gpe_block->block_base_number];
 
-	gpe_event_info->flags = (u8)
-	    (type | ACPI_GPE_DISPATCH_METHOD | ACPI_GPE_TYPE_RUNTIME);
+	gpe_event_info->flags = (u8) (type | ACPI_GPE_DISPATCH_METHOD);
 
 	gpe_event_info->dispatch.method_node =
 	    (struct acpi_namespace_node *)obj_handle;
 
-	/* Update enable mask, but don't enable the HW GPE as of yet */
-
-	status = acpi_ev_enable_gpe(gpe_event_info, FALSE);
-
 	ACPI_DEBUG_PRINT((ACPI_DB_LOAD,
 			  "Registered GPE method %s as GPE number 0x%.2X\n",
 			  name, gpe_number));
-	return_ACPI_STATUS(status);
+	return_ACPI_STATUS(AE_OK);
 }
 
 /*******************************************************************************
@@ -454,20 +447,7 @@
 							gpe_block->
 							block_base_number];
 
-		/* Mark GPE for WAKE-ONLY but WAKE_DISABLED */
-
-		gpe_event_info->flags &=
-		    ~(ACPI_GPE_WAKE_ENABLED | ACPI_GPE_RUN_ENABLED);
-
-		status =
-		    acpi_ev_set_gpe_type(gpe_event_info, ACPI_GPE_TYPE_WAKE);
-		if (ACPI_FAILURE(status)) {
-			goto cleanup;
-		}
-
-		status =
-		    acpi_ev_update_gpe_enable_masks(gpe_event_info,
-						    ACPI_GPE_DISABLE);
+		gpe_event_info->flags |= ACPI_GPE_CAN_WAKE;
 	}
 
       cleanup:
@@ -989,7 +969,6 @@
 acpi_ev_initialize_gpe_block(struct acpi_namespace_node *gpe_device,
 			     struct acpi_gpe_block_info *gpe_block)
 {
-	acpi_status status;
 	struct acpi_gpe_event_info *gpe_event_info;
 	struct acpi_gpe_walk_info gpe_info;
 	u32 wake_gpe_count;
@@ -1019,42 +998,50 @@
 		gpe_info.gpe_block = gpe_block;
 		gpe_info.gpe_device = gpe_device;
 
-		status =
-		    acpi_ns_walk_namespace(ACPI_TYPE_DEVICE, ACPI_ROOT_OBJECT,
+		acpi_ns_walk_namespace(ACPI_TYPE_DEVICE, ACPI_ROOT_OBJECT,
 					   ACPI_UINT32_MAX, ACPI_NS_WALK_UNLOCK,
 					   acpi_ev_match_prw_and_gpe, NULL,
 					   &gpe_info, NULL);
 	}
 
 	/*
-	 * Enable all GPEs in this block that have these attributes:
-	 * 1) are "runtime" or "run/wake" GPEs, and
-	 * 2) have a corresponding _Lxx or _Exx method
-	 *
-	 * Any other GPEs within this block must be enabled via the
-	 * acpi_enable_gpe() external interface.
+	 * Enable all GPEs that have a corresponding method and aren't
+	 * capable of generating wakeups. Any other GPEs within this block
+	 * must be enabled via the acpi_enable_gpe() interface.
 	 */
 	wake_gpe_count = 0;
 	gpe_enabled_count = 0;
+	if (gpe_device == acpi_gbl_fadt_gpe_device)
+		gpe_device = NULL;
 
 	for (i = 0; i < gpe_block->register_count; i++) {
-		for (j = 0; j < 8; j++) {
+		for (j = 0; j < ACPI_GPE_REGISTER_WIDTH; j++) {
+			acpi_status status;
+			acpi_size gpe_index;
+			int gpe_number;
 
 			/* Get the info block for this particular GPE */
+			gpe_index = (acpi_size)i * ACPI_GPE_REGISTER_WIDTH + j;
+			gpe_event_info = &gpe_block->event_info[gpe_index];
 
-			gpe_event_info = &gpe_block->event_info[((acpi_size) i *
-								 ACPI_GPE_REGISTER_WIDTH)
-								+ j];
-
-			if (((gpe_event_info->flags & ACPI_GPE_DISPATCH_MASK) ==
-			     ACPI_GPE_DISPATCH_METHOD) &&
-			    (gpe_event_info->flags & ACPI_GPE_TYPE_RUNTIME)) {
-				gpe_enabled_count++;
-			}
-
-			if (gpe_event_info->flags & ACPI_GPE_TYPE_WAKE) {
+			if (gpe_event_info->flags & ACPI_GPE_CAN_WAKE) {
 				wake_gpe_count++;
+				if (acpi_gbl_leave_wake_gpes_disabled)
+					continue;
 			}
+
+			if (!(gpe_event_info->flags & ACPI_GPE_DISPATCH_METHOD))
+				continue;
+
+			gpe_number = gpe_index + gpe_block->block_base_number;
+			status = acpi_enable_gpe(gpe_device, gpe_number,
+						ACPI_GPE_TYPE_RUNTIME);
+			if (ACPI_FAILURE(status))
+				ACPI_ERROR((AE_INFO,
+						"Failed to enable GPE %02X\n",
+						gpe_number));
+			else
+				gpe_enabled_count++;
 		}
 	}
 
@@ -1062,15 +1049,7 @@
 			  "Found %u Wake, Enabled %u Runtime GPEs in this block\n",
 			  wake_gpe_count, gpe_enabled_count));
 
-	/* Enable all valid runtime GPEs found above */
-
-	status = acpi_hw_enable_runtime_gpe_block(NULL, gpe_block, NULL);
-	if (ACPI_FAILURE(status)) {
-		ACPI_ERROR((AE_INFO, "Could not enable GPEs in GpeBlock %p",
-			    gpe_block));
-	}
-
-	return_ACPI_STATUS(status);
+	return_ACPI_STATUS(AE_OK);
 }
 
 /*******************************************************************************
diff --git a/drivers/acpi/acpica/evmisc.c b/drivers/acpi/acpica/evmisc.c
index ce224e1..8f0fac6 100644
--- a/drivers/acpi/acpica/evmisc.c
+++ b/drivers/acpi/acpica/evmisc.c
@@ -259,9 +259,15 @@
 
 	handler_obj = notify_info->notify.handler_obj;
 	if (handler_obj) {
-		handler_obj->notify.handler(notify_info->notify.node,
-					    notify_info->notify.value,
-					    handler_obj->notify.context);
+		struct acpi_object_notify_handler *notifier;
+
+		notifier = &handler_obj->notify;
+		while (notifier) {
+			notifier->handler(notify_info->notify.node,
+					  notify_info->notify.value,
+					  notifier->context);
+			notifier = notifier->next;
+		}
 	}
 
 	/* All done with the info object */
diff --git a/drivers/acpi/acpica/evxface.c b/drivers/acpi/acpica/evxface.c
index 2fe0809..474e2ca 100644
--- a/drivers/acpi/acpica/evxface.c
+++ b/drivers/acpi/acpica/evxface.c
@@ -218,6 +218,72 @@
 
 /*******************************************************************************
  *
+ * FUNCTION:    acpi_populate_handler_object
+ *
+ * PARAMETERS:  handler_obj        - Handler object to populate
+ *              handler_type       - The type of handler:
+ *                                  ACPI_SYSTEM_NOTIFY: system_handler (00-7f)
+ *                                  ACPI_DEVICE_NOTIFY: driver_handler (80-ff)
+ *                                  ACPI_ALL_NOTIFY:  both system and device
+ *              handler            - Address of the handler
+ *              context            - Value passed to the handler on each GPE
+ *              next               - Address of a handler object to link to
+ *
+ * RETURN:      None
+ *
+ * DESCRIPTION: Populate a handler object.
+ *
+ ******************************************************************************/
+static void
+acpi_populate_handler_object(struct acpi_object_notify_handler *handler_obj,
+			     u32 handler_type,
+			     acpi_notify_handler handler, void *context,
+			     struct acpi_object_notify_handler *next)
+{
+	handler_obj->handler_type = handler_type;
+	handler_obj->handler = handler;
+	handler_obj->context = context;
+	handler_obj->next = next;
+}
+
+/*******************************************************************************
+ *
+ * FUNCTION:    acpi_add_handler_object
+ *
+ * PARAMETERS:  parent_obj         - Parent of the new object
+ *              handler            - Address of the handler
+ *              context            - Value passed to the handler on each GPE
+ *
+ * RETURN:      Status
+ *
+ * DESCRIPTION: Create a new handler object and populate it.
+ *
+ ******************************************************************************/
+static acpi_status
+acpi_add_handler_object(struct acpi_object_notify_handler *parent_obj,
+			acpi_notify_handler handler, void *context)
+{
+	struct acpi_object_notify_handler *handler_obj;
+
+	/* The parent must not be a defice notify handler object. */
+	if (parent_obj->handler_type & ACPI_DEVICE_NOTIFY)
+		return AE_BAD_PARAMETER;
+
+	handler_obj = ACPI_ALLOCATE_ZEROED(sizeof(*handler_obj));
+	if (!handler_obj)
+		return AE_NO_MEMORY;
+
+	acpi_populate_handler_object(handler_obj,
+					ACPI_SYSTEM_NOTIFY,
+					handler, context,
+					parent_obj->next);
+	parent_obj->next = handler_obj;
+
+	return AE_OK;
+}
+
+/*******************************************************************************
+ *
  * FUNCTION:    acpi_install_notify_handler
  *
  * PARAMETERS:  Device          - The device for which notifies will be handled
@@ -316,15 +382,32 @@
 		obj_desc = acpi_ns_get_attached_object(node);
 		if (obj_desc) {
 
-			/* Object exists - make sure there's no handler */
+			/* Object exists. */
 
-			if (((handler_type & ACPI_SYSTEM_NOTIFY) &&
-			     obj_desc->common_notify.system_notify) ||
-			    ((handler_type & ACPI_DEVICE_NOTIFY) &&
-			     obj_desc->common_notify.device_notify)) {
+			/* For a device notify, make sure there's no handler. */
+			if ((handler_type & ACPI_DEVICE_NOTIFY) &&
+			     obj_desc->common_notify.device_notify) {
 				status = AE_ALREADY_EXISTS;
 				goto unlock_and_exit;
 			}
+
+			/* System notifies may have more handlers installed. */
+			notify_obj = obj_desc->common_notify.system_notify;
+
+			if ((handler_type & ACPI_SYSTEM_NOTIFY) && notify_obj) {
+				struct acpi_object_notify_handler *parent_obj;
+
+				if (handler_type & ACPI_DEVICE_NOTIFY) {
+					status = AE_ALREADY_EXISTS;
+					goto unlock_and_exit;
+				}
+
+				parent_obj = &notify_obj->notify;
+				status = acpi_add_handler_object(parent_obj,
+								 handler,
+								 context);
+				goto unlock_and_exit;
+			}
 		} else {
 			/* Create a new object */
 
@@ -356,9 +439,10 @@
 			goto unlock_and_exit;
 		}
 
-		notify_obj->notify.node = node;
-		notify_obj->notify.handler = handler;
-		notify_obj->notify.context = context;
+		acpi_populate_handler_object(&notify_obj->notify,
+						handler_type,
+						handler, context,
+						NULL);
 
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
 			obj_desc->common_notify.system_notify = notify_obj;
@@ -418,6 +502,10 @@
 		goto exit;
 	}
 
+
+	/* Make sure all deferred tasks are completed */
+	acpi_os_wait_events_complete(NULL);
+
 	status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
 	if (ACPI_FAILURE(status)) {
 		goto exit;
@@ -445,15 +533,6 @@
 			goto unlock_and_exit;
 		}
 
-		/* Make sure all deferred tasks are completed */
-
-		(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-		acpi_os_wait_events_complete(NULL);
-		status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-		if (ACPI_FAILURE(status)) {
-			goto exit;
-		}
-
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
 			acpi_gbl_system_notify.node = NULL;
 			acpi_gbl_system_notify.handler = NULL;
@@ -488,28 +567,60 @@
 		/* Object exists - make sure there's an existing handler */
 
 		if (handler_type & ACPI_SYSTEM_NOTIFY) {
+			struct acpi_object_notify_handler *handler_obj;
+			struct acpi_object_notify_handler *parent_obj;
+
 			notify_obj = obj_desc->common_notify.system_notify;
 			if (!notify_obj) {
 				status = AE_NOT_EXIST;
 				goto unlock_and_exit;
 			}
 
-			if (notify_obj->notify.handler != handler) {
+			handler_obj = &notify_obj->notify;
+			parent_obj = NULL;
+			while (handler_obj->handler != handler) {
+				if (handler_obj->next) {
+					parent_obj = handler_obj;
+					handler_obj = handler_obj->next;
+				} else {
+					break;
+				}
+			}
+
+			if (handler_obj->handler != handler) {
 				status = AE_BAD_PARAMETER;
 				goto unlock_and_exit;
 			}
-			/* Make sure all deferred tasks are completed */
 
-			(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-			acpi_os_wait_events_complete(NULL);
-			status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-			if (ACPI_FAILURE(status)) {
-				goto exit;
+			/*
+			 * Remove the handler.  There are three possible cases.
+			 * First, we may need to remove a non-embedded object.
+			 * Second, we may need to remove the embedded object's
+			 * handler data, while non-embedded objects exist.
+			 * Finally, we may need to remove the embedded object
+			 * entirely along with its container.
+			 */
+			if (parent_obj) {
+				/* Non-embedded object is being removed. */
+				parent_obj->next = handler_obj->next;
+				ACPI_FREE(handler_obj);
+			} else if (notify_obj->notify.next) {
+				/*
+				 * The handler matches the embedded object, but
+				 * there are more handler objects in the list.
+				 * Replace the embedded object's data with the
+				 * first next object's data and remove that
+				 * object.
+				 */
+				parent_obj = &notify_obj->notify;
+				handler_obj = notify_obj->notify.next;
+				*parent_obj = *handler_obj;
+				ACPI_FREE(handler_obj);
+			} else {
+				/* No more handler objects in the list. */
+				obj_desc->common_notify.system_notify = NULL;
+				acpi_ut_remove_reference(notify_obj);
 			}
-
-			/* Remove the handler */
-			obj_desc->common_notify.system_notify = NULL;
-			acpi_ut_remove_reference(notify_obj);
 		}
 
 		if (handler_type & ACPI_DEVICE_NOTIFY) {
@@ -523,14 +634,6 @@
 				status = AE_BAD_PARAMETER;
 				goto unlock_and_exit;
 			}
-			/* Make sure all deferred tasks are completed */
-
-			(void)acpi_ut_release_mutex(ACPI_MTX_NAMESPACE);
-			acpi_os_wait_events_complete(NULL);
-			status = acpi_ut_acquire_mutex(ACPI_MTX_NAMESPACE);
-			if (ACPI_FAILURE(status)) {
-				goto exit;
-			}
 
 			/* Remove the handler */
 			obj_desc->common_notify.device_notify = NULL;
@@ -617,13 +720,6 @@
 	handler->context = context;
 	handler->method_node = gpe_event_info->dispatch.method_node;
 
-	/* Disable the GPE before installing the handler */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-	if (ACPI_FAILURE(status)) {
-		goto unlock_and_exit;
-	}
-
 	/* Install the handler */
 
 	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
@@ -707,13 +803,6 @@
 		goto unlock_and_exit;
 	}
 
-	/* Disable the GPE before removing the handler */
-
-	status = acpi_ev_disable_gpe(gpe_event_info);
-	if (ACPI_FAILURE(status)) {
-		goto unlock_and_exit;
-	}
-
 	/* Make sure all deferred tasks are completed */
 
 	(void)acpi_ut_release_mutex(ACPI_MTX_EVENTS);
diff --git a/drivers/acpi/acpica/evxfevnt.c b/drivers/acpi/acpica/evxfevnt.c
index eed7a38..124c157 100644
--- a/drivers/acpi/acpica/evxfevnt.c
+++ b/drivers/acpi/acpica/evxfevnt.c
@@ -201,67 +201,25 @@
 
 /*******************************************************************************
  *
- * FUNCTION:    acpi_set_gpe_type
+ * FUNCTION:    acpi_set_gpe
  *
  * PARAMETERS:  gpe_device      - Parent GPE Device
  *              gpe_number      - GPE level within the GPE block
- *              Type            - New GPE type
- *
- * RETURN:      Status
- *
- * DESCRIPTION: Set the type of an individual GPE
- *
- ******************************************************************************/
-acpi_status acpi_set_gpe_type(acpi_handle gpe_device, u32 gpe_number, u8 type)
-{
-	acpi_status status = AE_OK;
-	struct acpi_gpe_event_info *gpe_event_info;
-
-	ACPI_FUNCTION_TRACE(acpi_set_gpe_type);
-
-	/* Ensure that we have a valid GPE number */
-
-	gpe_event_info = acpi_ev_get_gpe_event_info(gpe_device, gpe_number);
-	if (!gpe_event_info) {
-		status = AE_BAD_PARAMETER;
-		goto unlock_and_exit;
-	}
-
-	if ((gpe_event_info->flags & ACPI_GPE_TYPE_MASK) == type) {
-		return_ACPI_STATUS(AE_OK);
-	}
-
-	/* Set the new type (will disable GPE if currently enabled) */
-
-	status = acpi_ev_set_gpe_type(gpe_event_info, type);
-
-      unlock_and_exit:
-	return_ACPI_STATUS(status);
-}
-
-ACPI_EXPORT_SYMBOL(acpi_set_gpe_type)
-
-/*******************************************************************************
- *
- * FUNCTION:    acpi_enable_gpe
- *
- * PARAMETERS:  gpe_device      - Parent GPE Device
- *              gpe_number      - GPE level within the GPE block
- *              Flags           - Just enable, or also wake enable?
+ *              action          - Enable or disable
  *                                Called from ISR or not
  *
  * RETURN:      Status
  *
- * DESCRIPTION: Enable an ACPI event (general purpose)
+ * DESCRIPTION: Enable or disable an ACPI event (general purpose)
  *
  ******************************************************************************/
-acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number)
+acpi_status acpi_set_gpe(acpi_handle gpe_device, u32 gpe_number, u8 action)
 {
 	acpi_status status = AE_OK;
 	acpi_cpu_flags flags;
 	struct acpi_gpe_event_info *gpe_event_info;
 
-	ACPI_FUNCTION_TRACE(acpi_enable_gpe);
+	ACPI_FUNCTION_TRACE(acpi_set_gpe);
 
 	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
 
@@ -273,15 +231,90 @@
 		goto unlock_and_exit;
 	}
 
-	/* Perform the enable */
+	/* Perform the action */
 
-	status = acpi_ev_enable_gpe(gpe_event_info, TRUE);
+	switch (action) {
+	case ACPI_GPE_ENABLE:
+		status = acpi_ev_enable_gpe(gpe_event_info);
+		break;
+
+	case ACPI_GPE_DISABLE:
+		status = acpi_ev_disable_gpe(gpe_event_info);
+		break;
+
+	default:
+		ACPI_ERROR((AE_INFO, "Invalid action\n"));
+		status = AE_BAD_PARAMETER;
+		break;
+	}
 
       unlock_and_exit:
 	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 	return_ACPI_STATUS(status);
 }
 
+ACPI_EXPORT_SYMBOL(acpi_set_gpe)
+
+/*******************************************************************************
+ *
+ * FUNCTION:    acpi_enable_gpe
+ *
+ * PARAMETERS:  gpe_device      - Parent GPE Device
+ *              gpe_number      - GPE level within the GPE block
+ *              type            - Purpose the GPE will be used for
+ *
+ * RETURN:      Status
+ *
+ * DESCRIPTION: Take a reference to a GPE and enable it if necessary
+ *
+ ******************************************************************************/
+acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type)
+{
+	acpi_status status = AE_OK;
+	acpi_cpu_flags flags;
+	struct acpi_gpe_event_info *gpe_event_info;
+
+	ACPI_FUNCTION_TRACE(acpi_enable_gpe);
+
+	if (type & ~ACPI_GPE_TYPE_WAKE_RUN)
+		return_ACPI_STATUS(AE_BAD_PARAMETER);
+
+	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
+
+	/* Ensure that we have a valid GPE number */
+
+	gpe_event_info = acpi_ev_get_gpe_event_info(gpe_device, gpe_number);
+	if (!gpe_event_info) {
+		status = AE_BAD_PARAMETER;
+		goto unlock_and_exit;
+	}
+
+	if (type & ACPI_GPE_TYPE_RUNTIME) {
+		if (++gpe_event_info->runtime_count == 1) {
+			status = acpi_ev_enable_gpe(gpe_event_info);
+			if (ACPI_FAILURE(status))
+				gpe_event_info->runtime_count--;
+		}
+	}
+
+	if (type & ACPI_GPE_TYPE_WAKE) {
+		if (!(gpe_event_info->flags & ACPI_GPE_CAN_WAKE)) {
+			status = AE_BAD_PARAMETER;
+			goto unlock_and_exit;
+		}
+
+		/*
+		 * Wake-up GPEs are only enabled right prior to putting the
+		 * system into a sleep state.
+		 */
+		if (++gpe_event_info->wakeup_count == 1)
+			acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	}
+
+unlock_and_exit:
+	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
+	return_ACPI_STATUS(status);
+}
 ACPI_EXPORT_SYMBOL(acpi_enable_gpe)
 
 /*******************************************************************************
@@ -290,15 +323,14 @@
  *
  * PARAMETERS:  gpe_device      - Parent GPE Device
  *              gpe_number      - GPE level within the GPE block
- *              Flags           - Just disable, or also wake disable?
- *                                Called from ISR or not
+ *              type            - Purpose the GPE won't be used for any more
  *
  * RETURN:      Status
  *
- * DESCRIPTION: Disable an ACPI event (general purpose)
+ * DESCRIPTION: Release a reference to a GPE and disable it if necessary
  *
  ******************************************************************************/
-acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number)
+acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type)
 {
 	acpi_status status = AE_OK;
 	acpi_cpu_flags flags;
@@ -306,6 +338,9 @@
 
 	ACPI_FUNCTION_TRACE(acpi_disable_gpe);
 
+	if (type & ~ACPI_GPE_TYPE_WAKE_RUN)
+		return_ACPI_STATUS(AE_BAD_PARAMETER);
+
 	flags = acpi_os_acquire_lock(acpi_gbl_gpe_lock);
 	/* Ensure that we have a valid GPE number */
 
@@ -315,13 +350,24 @@
 		goto unlock_and_exit;
 	}
 
-	status = acpi_ev_disable_gpe(gpe_event_info);
+	if ((type & ACPI_GPE_TYPE_RUNTIME) && gpe_event_info->runtime_count) {
+		if (--gpe_event_info->runtime_count == 0)
+			status = acpi_ev_disable_gpe(gpe_event_info);
+	}
+
+	if ((type & ACPI_GPE_TYPE_WAKE) && gpe_event_info->wakeup_count) {
+		/*
+		 * Wake-up GPEs are not enabled after leaving system sleep
+		 * states, so we don't need to disable them here.
+		 */
+		if (--gpe_event_info->wakeup_count == 0)
+			acpi_ev_update_gpe_enable_masks(gpe_event_info);
+	}
 
 unlock_and_exit:
 	acpi_os_release_lock(acpi_gbl_gpe_lock, flags);
 	return_ACPI_STATUS(status);
 }
-
 ACPI_EXPORT_SYMBOL(acpi_disable_gpe)
 
 /*******************************************************************************
diff --git a/drivers/acpi/button.c b/drivers/acpi/button.c
index 8a95e83..f53fbe3 100644
--- a/drivers/acpi/button.c
+++ b/drivers/acpi/button.c
@@ -422,11 +422,10 @@
 
 	if (device->wakeup.flags.valid) {
 		/* Button's GPE is run-wake GPE */
-		acpi_set_gpe_type(device->wakeup.gpe_device,
-				  device->wakeup.gpe_number,
-				  ACPI_GPE_TYPE_WAKE_RUN);
 		acpi_enable_gpe(device->wakeup.gpe_device,
-				device->wakeup.gpe_number);
+				device->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE_RUN);
+		device->wakeup.run_wake_count++;
 		device->wakeup.state.enabled = 1;
 	}
 
@@ -446,6 +445,14 @@
 {
 	struct acpi_button *button = acpi_driver_data(device);
 
+	if (device->wakeup.flags.valid) {
+		acpi_disable_gpe(device->wakeup.gpe_device,
+				device->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE_RUN);
+		device->wakeup.run_wake_count--;
+		device->wakeup.state.enabled = 0;
+	}
+
 	acpi_button_remove_fs(device);
 	input_unregister_device(button->input);
 	kfree(button);
diff --git a/drivers/acpi/ec.c b/drivers/acpi/ec.c
index d6471bb..27e0b92 100644
--- a/drivers/acpi/ec.c
+++ b/drivers/acpi/ec.c
@@ -307,7 +307,11 @@
 	pr_debug(PREFIX "transaction start\n");
 	/* disable GPE during transaction if storm is detected */
 	if (test_bit(EC_FLAGS_GPE_STORM, &ec->flags)) {
-		acpi_disable_gpe(NULL, ec->gpe);
+		/*
+		 * It has to be disabled at the hardware level regardless of the
+		 * GPE reference counting, so that it doesn't trigger.
+		 */
+		acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_DISABLE);
 	}
 
 	status = acpi_ec_transaction_unlocked(ec, t);
@@ -316,8 +320,12 @@
 	ec_check_sci_sync(ec, acpi_ec_read_status(ec));
 	if (test_bit(EC_FLAGS_GPE_STORM, &ec->flags)) {
 		msleep(1);
-		/* it is safe to enable GPE outside of transaction */
-		acpi_enable_gpe(NULL, ec->gpe);
+		/*
+		 * It is safe to enable the GPE outside of the transaction.  Use
+		 * acpi_set_gpe() for that, since we used it to disable the GPE
+		 * above.
+		 */
+		acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_ENABLE);
 	} else if (t->irq_count > ACPI_EC_STORM_THRESHOLD) {
 		pr_info(PREFIX "GPE storm detected, "
 			"transactions will use polling mode\n");
@@ -788,8 +796,8 @@
 				  &acpi_ec_gpe_handler, ec);
 	if (ACPI_FAILURE(status))
 		return -ENODEV;
-	acpi_set_gpe_type(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
-	acpi_enable_gpe(NULL, ec->gpe);
+
+	acpi_enable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 	status = acpi_install_address_space_handler(ec->handle,
 						    ACPI_ADR_SPACE_EC,
 						    &acpi_ec_space_handler,
@@ -806,6 +814,7 @@
 		} else {
 			acpi_remove_gpe_handler(NULL, ec->gpe,
 				&acpi_ec_gpe_handler);
+			acpi_disable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 			return -ENODEV;
 		}
 	}
@@ -816,6 +825,7 @@
 
 static void ec_remove_handlers(struct acpi_ec *ec)
 {
+	acpi_disable_gpe(NULL, ec->gpe, ACPI_GPE_TYPE_RUNTIME);
 	if (ACPI_FAILURE(acpi_remove_address_space_handler(ec->handle,
 				ACPI_ADR_SPACE_EC, &acpi_ec_space_handler)))
 		pr_err(PREFIX "failed to remove space handler\n");
@@ -1057,16 +1067,16 @@
 static int acpi_ec_suspend(struct acpi_device *device, pm_message_t state)
 {
 	struct acpi_ec *ec = acpi_driver_data(device);
-	/* Stop using GPE */
-	acpi_disable_gpe(NULL, ec->gpe);
+	/* Stop using the GPE, but keep it reference counted. */
+	acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_DISABLE);
 	return 0;
 }
 
 static int acpi_ec_resume(struct acpi_device *device)
 {
 	struct acpi_ec *ec = acpi_driver_data(device);
-	/* Enable use of GPE back */
-	acpi_enable_gpe(NULL, ec->gpe);
+	/* Enable the GPE again, but don't reference count it once more. */
+	acpi_set_gpe(NULL, ec->gpe, ACPI_GPE_ENABLE);
 	return 0;
 }
 
diff --git a/drivers/acpi/internal.h b/drivers/acpi/internal.h
index cb28e05..9c4c962 100644
--- a/drivers/acpi/internal.h
+++ b/drivers/acpi/internal.h
@@ -36,8 +36,6 @@
 int acpi_power_init(void);
 int acpi_device_sleep_wake(struct acpi_device *dev,
                            int enable, int sleep_state, int dev_state);
-int acpi_enable_wakeup_device_power(struct acpi_device *dev, int sleep_state);
-int acpi_disable_wakeup_device_power(struct acpi_device *dev);
 int acpi_power_get_inferred_state(struct acpi_device *device);
 int acpi_power_transition(struct acpi_device *device, int state);
 extern int acpi_power_nocheck;
diff --git a/drivers/acpi/pci_bind.c b/drivers/acpi/pci_bind.c
index a5a77b7..2ef0409 100644
--- a/drivers/acpi/pci_bind.c
+++ b/drivers/acpi/pci_bind.c
@@ -26,7 +26,9 @@
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/pci.h>
+#include <linux/pci-acpi.h>
 #include <linux/acpi.h>
+#include <linux/pm_runtime.h>
 #include <acpi/acpi_bus.h>
 #include <acpi/acpi_drivers.h>
 
@@ -38,7 +40,13 @@
 	struct pci_dev *dev;
 
 	dev = acpi_get_pci_dev(device->handle);
-	if (!dev || !dev->subordinate)
+	if (!dev)
+		goto out;
+
+	device_set_run_wake(&dev->dev, false);
+	pci_acpi_remove_pm_notifier(device);
+
+	if (!dev->subordinate)
 		goto out;
 
 	acpi_pci_irq_del_prt(dev->subordinate);
@@ -62,6 +70,10 @@
 	if (!dev)
 		return 0;
 
+	pci_acpi_add_pm_notifier(device, dev);
+	if (device->wakeup.flags.run_wake)
+		device_set_run_wake(&dev->dev, true);
+
 	/*
 	 * Install the 'bind' function to facilitate callbacks for
 	 * children of the P2P bridge.
diff --git a/drivers/acpi/pci_root.c b/drivers/acpi/pci_root.c
index 64f55b6..d724736 100644
--- a/drivers/acpi/pci_root.c
+++ b/drivers/acpi/pci_root.c
@@ -30,6 +30,7 @@
 #include <linux/proc_fs.h>
 #include <linux/spinlock.h>
 #include <linux/pm.h>
+#include <linux/pm_runtime.h>
 #include <linux/pci.h>
 #include <linux/pci-acpi.h>
 #include <linux/acpi.h>
@@ -528,6 +529,10 @@
 	if (flags != base_flags)
 		acpi_pci_osc_support(root, flags);
 
+	pci_acpi_add_bus_pm_notifier(device, root->bus);
+	if (device->wakeup.flags.run_wake)
+		device_set_run_wake(root->bus->bridge, true);
+
 	return 0;
 
 end:
@@ -549,6 +554,9 @@
 {
 	struct acpi_pci_root *root = acpi_driver_data(device);
 
+	device_set_run_wake(root->bus->bridge, false);
+	pci_acpi_remove_bus_pm_notifier(device);
+
 	kfree(root);
 	return 0;
 }
@@ -558,6 +566,7 @@
 	if (acpi_pci_disabled)
 		return 0;
 
+	pci_acpi_crs_quirks();
 	if (acpi_bus_register_driver(&acpi_pci_root_driver) < 0)
 		return -ENODEV;
 
diff --git a/drivers/acpi/scan.c b/drivers/acpi/scan.c
index 3e00967..fb7fc24 100644
--- a/drivers/acpi/scan.c
+++ b/drivers/acpi/scan.c
@@ -741,19 +741,40 @@
 	return AE_OK;
 }
 
-static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
+static void acpi_bus_set_run_wake_flags(struct acpi_device *device)
 {
-	acpi_status status = 0;
-	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
-	union acpi_object *package = NULL;
-	int psw_error;
-
 	struct acpi_device_id button_device_ids[] = {
 		{"PNP0C0D", 0},
 		{"PNP0C0C", 0},
 		{"PNP0C0E", 0},
 		{"", 0},
 	};
+	acpi_status status;
+	acpi_event_status event_status;
+
+	device->wakeup.run_wake_count = 0;
+	device->wakeup.flags.notifier_present = 0;
+
+	/* Power button, Lid switch always enable wakeup */
+	if (!acpi_match_device_ids(device, button_device_ids)) {
+		device->wakeup.flags.run_wake = 1;
+		device->wakeup.flags.always_enabled = 1;
+		return;
+	}
+
+	status = acpi_get_gpe_status(NULL, device->wakeup.gpe_number,
+					ACPI_NOT_ISR, &event_status);
+	if (status == AE_OK)
+		device->wakeup.flags.run_wake =
+				!!(event_status & ACPI_EVENT_FLAG_HANDLE);
+}
+
+static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
+{
+	acpi_status status = 0;
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *package = NULL;
+	int psw_error;
 
 	/* _PRW */
 	status = acpi_evaluate_object(device->handle, "_PRW", NULL, &buffer);
@@ -773,6 +794,7 @@
 
 	device->wakeup.flags.valid = 1;
 	device->wakeup.prepare_count = 0;
+	acpi_bus_set_run_wake_flags(device);
 	/* Call _PSW/_DSW object to disable its ability to wake the sleeping
 	 * system for the ACPI device with the _PRW object.
 	 * The _PSW object is depreciated in ACPI 3.0 and is replaced by _DSW.
@@ -784,10 +806,6 @@
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 				"error in _DSW or _PSW evaluation\n"));
 
-	/* Power button, Lid switch always enable wakeup */
-	if (!acpi_match_device_ids(device, button_device_ids))
-		device->wakeup.flags.run_wake = 1;
-
 end:
 	if (ACPI_FAILURE(status))
 		device->flags.wake_capable = 0;
diff --git a/drivers/acpi/sleep.c b/drivers/acpi/sleep.c
index 79d33d9..3bde594 100644
--- a/drivers/acpi/sleep.c
+++ b/drivers/acpi/sleep.c
@@ -745,9 +745,18 @@
 		return -ENODEV;
 	}
 
-	error = enable ?
-		acpi_enable_wakeup_device_power(adev, acpi_target_sleep_state) :
-		acpi_disable_wakeup_device_power(adev);
+	if (enable) {
+		error = acpi_enable_wakeup_device_power(adev,
+						acpi_target_sleep_state);
+		if (!error)
+			acpi_enable_gpe(adev->wakeup.gpe_device,
+					adev->wakeup.gpe_number,
+					ACPI_GPE_TYPE_WAKE);
+	} else {
+		acpi_disable_gpe(adev->wakeup.gpe_device, adev->wakeup.gpe_number,
+				ACPI_GPE_TYPE_WAKE);
+		error = acpi_disable_wakeup_device_power(adev);
+	}
 	if (!error)
 		dev_info(dev, "wake-up capability %s by ACPI\n",
 				enable ? "enabled" : "disabled");
diff --git a/drivers/acpi/system.c b/drivers/acpi/system.c
index d112829..a206a12 100644
--- a/drivers/acpi/system.c
+++ b/drivers/acpi/system.c
@@ -387,10 +387,10 @@
 	if (index < num_gpes) {
 		if (!strcmp(buf, "disable\n") &&
 				(status & ACPI_EVENT_FLAG_ENABLED))
-			result = acpi_disable_gpe(handle, index);
+			result = acpi_set_gpe(handle, index, ACPI_GPE_DISABLE);
 		else if (!strcmp(buf, "enable\n") &&
 				!(status & ACPI_EVENT_FLAG_ENABLED))
-			result = acpi_enable_gpe(handle, index);
+			result = acpi_set_gpe(handle, index, ACPI_GPE_ENABLE);
 		else if (!strcmp(buf, "clear\n") &&
 				(status & ACPI_EVENT_FLAG_SET))
 			result = acpi_clear_gpe(handle, index, ACPI_NOT_ISR);
diff --git a/drivers/acpi/wakeup.c b/drivers/acpi/wakeup.c
index e0ee0c0..4b9d339 100644
--- a/drivers/acpi/wakeup.c
+++ b/drivers/acpi/wakeup.c
@@ -21,12 +21,12 @@
 ACPI_MODULE_NAME("wakeup_devices")
 
 /**
- * acpi_enable_wakeup_device_prep - prepare wakeup devices
- *	@sleep_state:	ACPI state
- * Enable all wakup devices power if the devices' wakeup level
- * is higher than requested sleep level
+ * acpi_enable_wakeup_device_prep - Prepare wake-up devices.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * Enable all wake-up devices' power, unless the requested system sleep state is
+ * too deep.
  */
-
 void acpi_enable_wakeup_device_prep(u8 sleep_state)
 {
 	struct list_head *node, *next;
@@ -36,9 +36,8 @@
 						       struct acpi_device,
 						       wakeup_list);
 
-		if (!dev->wakeup.flags.valid ||
-		    !dev->wakeup.state.enabled ||
-		    (sleep_state > (u32) dev->wakeup.sleep_state))
+		if (!dev->wakeup.flags.valid || !dev->wakeup.state.enabled
+		    || (sleep_state > (u32) dev->wakeup.sleep_state))
 			continue;
 
 		acpi_enable_wakeup_device_power(dev, sleep_state);
@@ -46,9 +45,12 @@
 }
 
 /**
- * acpi_enable_wakeup_device - enable wakeup devices
- *	@sleep_state:	ACPI state
- * Enable all wakup devices's GPE
+ * acpi_enable_wakeup_device - Enable wake-up device GPEs.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * Enable all wake-up devices' GPEs, with the assumption that
+ * acpi_disable_all_gpes() was executed before, so we don't need to disable any
+ * GPEs here.
  */
 void acpi_enable_wakeup_device(u8 sleep_state)
 {
@@ -65,29 +67,22 @@
 		if (!dev->wakeup.flags.valid)
 			continue;
 
-		/* If users want to disable run-wake GPE,
-		 * we only disable it for wake and leave it for runtime
-		 */
 		if ((!dev->wakeup.state.enabled && !dev->wakeup.prepare_count)
-		    || sleep_state > (u32) dev->wakeup.sleep_state) {
-			if (dev->wakeup.flags.run_wake) {
-				/* set_gpe_type will disable GPE, leave it like that */
-				acpi_set_gpe_type(dev->wakeup.gpe_device,
-						  dev->wakeup.gpe_number,
-						  ACPI_GPE_TYPE_RUNTIME);
-			}
+		    || sleep_state > (u32) dev->wakeup.sleep_state)
 			continue;
-		}
-		if (!dev->wakeup.flags.run_wake)
-			acpi_enable_gpe(dev->wakeup.gpe_device,
-					dev->wakeup.gpe_number);
+
+		/* The wake-up power should have been enabled already. */
+		acpi_set_gpe(dev->wakeup.gpe_device, dev->wakeup.gpe_number,
+				ACPI_GPE_ENABLE);
 	}
 }
 
 /**
- * acpi_disable_wakeup_device - disable devices' wakeup capability
- *	@sleep_state:	ACPI state
- * Disable all wakup devices's GPE and wakeup capability
+ * acpi_disable_wakeup_device - Disable devices' wakeup capability.
+ * @sleep_state: ACPI system sleep state.
+ *
+ * This function only affects devices with wakeup.state.enabled set, which means
+ * that it reverses the changes made by acpi_enable_wakeup_device_prep().
  */
 void acpi_disable_wakeup_device(u8 sleep_state)
 {
@@ -97,30 +92,11 @@
 		struct acpi_device *dev =
 			container_of(node, struct acpi_device, wakeup_list);
 
-		if (!dev->wakeup.flags.valid)
+		if (!dev->wakeup.flags.valid || !dev->wakeup.state.enabled
+		    || (sleep_state > (u32) dev->wakeup.sleep_state))
 			continue;
 
-		if ((!dev->wakeup.state.enabled && !dev->wakeup.prepare_count)
-		    || sleep_state > (u32) dev->wakeup.sleep_state) {
-			if (dev->wakeup.flags.run_wake) {
-				acpi_set_gpe_type(dev->wakeup.gpe_device,
-						  dev->wakeup.gpe_number,
-						  ACPI_GPE_TYPE_WAKE_RUN);
-				/* Re-enable it, since set_gpe_type will disable it */
-				acpi_enable_gpe(dev->wakeup.gpe_device,
-						dev->wakeup.gpe_number);
-			}
-			continue;
-		}
-
 		acpi_disable_wakeup_device_power(dev);
-		/* Never disable run-wake GPE */
-		if (!dev->wakeup.flags.run_wake) {
-			acpi_disable_gpe(dev->wakeup.gpe_device,
-					 dev->wakeup.gpe_number);
-			acpi_clear_gpe(dev->wakeup.gpe_device,
-				       dev->wakeup.gpe_number, ACPI_NOT_ISR);
-		}
 	}
 }
 
@@ -134,13 +110,11 @@
 						       struct acpi_device,
 						       wakeup_list);
 		/* In case user doesn't load button driver */
-		if (!dev->wakeup.flags.run_wake || dev->wakeup.state.enabled)
+		if (!dev->wakeup.flags.always_enabled ||
+		    dev->wakeup.state.enabled)
 			continue;
-		acpi_set_gpe_type(dev->wakeup.gpe_device,
-				  dev->wakeup.gpe_number,
-				  ACPI_GPE_TYPE_WAKE_RUN);
-		acpi_enable_gpe(dev->wakeup.gpe_device,
-				dev->wakeup.gpe_number);
+ 		acpi_enable_gpe(dev->wakeup.gpe_device, dev->wakeup.gpe_number,
+ 				ACPI_GPE_TYPE_WAKE);
 		dev->wakeup.state.enabled = 1;
 	}
 	mutex_unlock(&acpi_device_lock);
diff --git a/drivers/isdn/hisax/Kconfig b/drivers/isdn/hisax/Kconfig
index 3464ebc..452fde9 100644
--- a/drivers/isdn/hisax/Kconfig
+++ b/drivers/isdn/hisax/Kconfig
@@ -109,7 +109,7 @@
 
 config HISAX_TELESPCI
 	bool "Teles PCI"
-	depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
+	depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
 	help
 	  This enables HiSax support for the Teles PCI.
 	  See <file:Documentation/isdn/README.HiSax> on how to configure it.
@@ -237,7 +237,7 @@
 
 config HISAX_NETJET
 	bool "NETjet card"
-	depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
+	depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
 	help
 	  This enables HiSax support for the NetJet from Traverse
 	  Technologies.
@@ -248,7 +248,7 @@
 
 config HISAX_NETJET_U
 	bool "NETspider U card"
-	depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
+	depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
 	help
 	  This enables HiSax support for the Netspider U interface ISDN card
 	  from Traverse Technologies.
@@ -287,7 +287,7 @@
 
 config HISAX_BKM_A4T
 	bool "Telekom A4T card"
-	depends on PCI && PCI_LEGACY
+	depends on PCI
 	help
 	  This enables HiSax support for the Telekom A4T card.
 
@@ -297,7 +297,7 @@
 
 config HISAX_SCT_QUADRO
 	bool "Scitel Quadro card"
-	depends on PCI && PCI_LEGACY
+	depends on PCI
 	help
 	  This enables HiSax support for the Scitel Quadro card.
 
@@ -316,7 +316,7 @@
 
 config HISAX_HFC_PCI
 	bool "HFC PCI-Bus cards"
-	depends on PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
+	depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
 	help
 	  This enables HiSax support for the HFC-S PCI 2BDS0 based cards.
 
@@ -325,7 +325,7 @@
 
 config HISAX_W6692
 	bool "Winbond W6692 based cards"
-	depends on PCI && PCI_LEGACY
+	depends on PCI
 	help
 	  This enables HiSax support for Winbond W6692 based PCI ISDN cards.
 
@@ -341,7 +341,7 @@
 
 config HISAX_ENTERNOW_PCI
 	bool "Formula-n enter:now PCI card"
-	depends on HISAX_NETJET && PCI && PCI_LEGACY && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
+	depends on HISAX_NETJET && PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || FRV))
 	help
 	  This enables HiSax support for the Formula-n enter:now PCI
 	  ISDN card.
@@ -412,7 +412,7 @@
 
 config HISAX_FRITZ_PCIPNP
 	tristate "AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)"
-	depends on PCI && PCI_LEGACY && EXPERIMENTAL
+	depends on PCI && EXPERIMENTAL
 	help
 	  This enables the driver for the AVM Fritz!Card PCI,
 	  Fritz!Card PCI v2 and Fritz!Card PnP.
diff --git a/drivers/isdn/hisax/avm_pci.c b/drivers/isdn/hisax/avm_pci.c
index 7cabc5a..14295a1 100644
--- a/drivers/isdn/hisax/avm_pci.c
+++ b/drivers/isdn/hisax/avm_pci.c
@@ -822,7 +822,7 @@
 
 #endif /* __ISAPNP__ */
 
-#ifndef CONFIG_PCI_LEGACY
+#ifndef CONFIG_PCI
 
 static int __devinit avm_pci_setup(struct IsdnCardState *cs)
 {
@@ -835,7 +835,7 @@
 
 static int __devinit avm_pci_setup(struct IsdnCardState *cs)
 {
-	if ((dev_avm = pci_find_device(PCI_VENDOR_ID_AVM,
+	if ((dev_avm = hisax_find_pci_device(PCI_VENDOR_ID_AVM,
 		PCI_DEVICE_ID_AVM_A1, dev_avm))) {
 
 		if (pci_enable_device(dev_avm))
@@ -864,7 +864,7 @@
 	return (1);
 }
 
-#endif /* CONFIG_PCI_LEGACY */
+#endif /* CONFIG_PCI */
 
 int __devinit
 setup_avm_pcipnp(struct IsdnCard *card)
diff --git a/drivers/isdn/hisax/bkm_a4t.c b/drivers/isdn/hisax/bkm_a4t.c
index 9ca2ee5..9f2009c 100644
--- a/drivers/isdn/hisax/bkm_a4t.c
+++ b/drivers/isdn/hisax/bkm_a4t.c
@@ -340,7 +340,7 @@
 	} else
 		return (0);
 
-	while ((dev_a4t = pci_find_device(PCI_VENDOR_ID_ZORAN,
+	while ((dev_a4t = hisax_find_pci_device(PCI_VENDOR_ID_ZORAN,
 		PCI_DEVICE_ID_ZORAN_36120, dev_a4t))) {
 		ret = a4t_pci_probe(dev_a4t, cs, &found, &pci_memaddr);
 		if (!ret)
diff --git a/drivers/isdn/hisax/bkm_a8.c b/drivers/isdn/hisax/bkm_a8.c
index e1ff471..e775706 100644
--- a/drivers/isdn/hisax/bkm_a8.c
+++ b/drivers/isdn/hisax/bkm_a8.c
@@ -301,7 +301,7 @@
 		(sub_vendor_id != PCI_VENDOR_ID_BERKOM)))
 		return (0);
 	if (cs->subtyp == SCT_1) {
-		while ((dev_a8 = pci_find_device(PCI_VENDOR_ID_PLX,
+		while ((dev_a8 = hisax_find_pci_device(PCI_VENDOR_ID_PLX,
 			PCI_DEVICE_ID_PLX_9050, dev_a8))) {
 			
 			sub_vendor_id = dev_a8->subsystem_vendor;
diff --git a/drivers/isdn/hisax/diva.c b/drivers/isdn/hisax/diva.c
index 0b0c2e5..780da9b 100644
--- a/drivers/isdn/hisax/diva.c
+++ b/drivers/isdn/hisax/diva.c
@@ -1148,7 +1148,7 @@
 
 #endif	/* ISAPNP */
 
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 static struct pci_dev *dev_diva __devinitdata = NULL;
 static struct pci_dev *dev_diva_u __devinitdata = NULL;
 static struct pci_dev *dev_diva201 __devinitdata = NULL;
@@ -1159,21 +1159,21 @@
 	struct IsdnCardState *cs = card->cs;
 
 	cs->subtyp = 0;
-	if ((dev_diva = pci_find_device(PCI_VENDOR_ID_EICON,
+	if ((dev_diva = hisax_find_pci_device(PCI_VENDOR_ID_EICON,
 		PCI_DEVICE_ID_EICON_DIVA20, dev_diva))) {
 		if (pci_enable_device(dev_diva))
 			return(0);
 		cs->subtyp = DIVA_PCI;
 		cs->irq = dev_diva->irq;
 		cs->hw.diva.cfg_reg = pci_resource_start(dev_diva, 2);
-	} else if ((dev_diva_u = pci_find_device(PCI_VENDOR_ID_EICON,
+	} else if ((dev_diva_u = hisax_find_pci_device(PCI_VENDOR_ID_EICON,
 		PCI_DEVICE_ID_EICON_DIVA20_U, dev_diva_u))) {
 		if (pci_enable_device(dev_diva_u))
 			return(0);
 		cs->subtyp = DIVA_PCI;
 		cs->irq = dev_diva_u->irq;
 		cs->hw.diva.cfg_reg = pci_resource_start(dev_diva_u, 2);
-	} else if ((dev_diva201 = pci_find_device(PCI_VENDOR_ID_EICON,
+	} else if ((dev_diva201 = hisax_find_pci_device(PCI_VENDOR_ID_EICON,
 		PCI_DEVICE_ID_EICON_DIVA201, dev_diva201))) {
 		if (pci_enable_device(dev_diva201))
 			return(0);
@@ -1183,7 +1183,7 @@
 			(ulong) ioremap(pci_resource_start(dev_diva201, 0), 4096);
 		cs->hw.diva.cfg_reg =
 			(ulong) ioremap(pci_resource_start(dev_diva201, 1), 4096);
-	} else if ((dev_diva202 = pci_find_device(PCI_VENDOR_ID_EICON,
+	} else if ((dev_diva202 = hisax_find_pci_device(PCI_VENDOR_ID_EICON,
 		PCI_DEVICE_ID_EICON_DIVA202, dev_diva202))) {
 		if (pci_enable_device(dev_diva202))
 			return(0);
@@ -1229,14 +1229,14 @@
 	return (1);		/* card found */
 }
 
-#else	/* if !CONFIG_PCI_LEGACY */
+#else	/* if !CONFIG_PCI */
 
 static int __devinit setup_diva_pci(struct IsdnCard *card)
 {
 	return (-1);	/* card not found; continue search */
 }
 
-#endif	/* CONFIG_PCI_LEGACY */
+#endif	/* CONFIG_PCI */
 
 int __devinit
 setup_diva(struct IsdnCard *card)
diff --git a/drivers/isdn/hisax/elsa.c b/drivers/isdn/hisax/elsa.c
index aa29d1c..23c41fc 100644
--- a/drivers/isdn/hisax/elsa.c
+++ b/drivers/isdn/hisax/elsa.c
@@ -1025,7 +1025,7 @@
 	       cs->irq);
 }
 
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 static 	struct pci_dev *dev_qs1000 __devinitdata = NULL;
 static 	struct pci_dev *dev_qs3000 __devinitdata = NULL;
 
@@ -1035,7 +1035,7 @@
 	struct IsdnCardState *cs = card->cs;
 
 	cs->subtyp = 0;
-	if ((dev_qs1000 = pci_find_device(PCI_VENDOR_ID_ELSA,
+	if ((dev_qs1000 = hisax_find_pci_device(PCI_VENDOR_ID_ELSA,
 		PCI_DEVICE_ID_ELSA_MICROLINK, dev_qs1000))) {
 		if (pci_enable_device(dev_qs1000))
 			return(0);
@@ -1043,7 +1043,7 @@
 		cs->irq = dev_qs1000->irq;
 		cs->hw.elsa.cfg = pci_resource_start(dev_qs1000, 1);
 		cs->hw.elsa.base = pci_resource_start(dev_qs1000, 3);
-	} else if ((dev_qs3000 = pci_find_device(PCI_VENDOR_ID_ELSA,
+	} else if ((dev_qs3000 = hisax_find_pci_device(PCI_VENDOR_ID_ELSA,
 		PCI_DEVICE_ID_ELSA_QS3000, dev_qs3000))) {
 		if (pci_enable_device(dev_qs3000))
 			return(0);
@@ -1093,7 +1093,7 @@
 {
 	return (1);
 }
-#endif /* CONFIG_PCI_LEGACY */
+#endif /* CONFIG_PCI */
 
 static int __devinit
 setup_elsa_common(struct IsdnCard *card)
diff --git a/drivers/isdn/hisax/enternow_pci.c b/drivers/isdn/hisax/enternow_pci.c
index 39f421e..26264ab 100644
--- a/drivers/isdn/hisax/enternow_pci.c
+++ b/drivers/isdn/hisax/enternow_pci.c
@@ -406,7 +406,7 @@
 
 	for ( ;; )
 	{
-		if ((dev_netjet = pci_find_device(PCI_VENDOR_ID_TIGERJET,
+		if ((dev_netjet = hisax_find_pci_device(PCI_VENDOR_ID_TIGERJET,
 			PCI_DEVICE_ID_TIGERJET_300,  dev_netjet))) {
 			ret = en_pci_probe(dev_netjet, cs);
 			if (!ret)
diff --git a/drivers/isdn/hisax/gazel.c b/drivers/isdn/hisax/gazel.c
index 0ea3b46..353982f 100644
--- a/drivers/isdn/hisax/gazel.c
+++ b/drivers/isdn/hisax/gazel.c
@@ -531,7 +531,7 @@
 	return (0);
 }
 
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 static struct pci_dev *dev_tel __devinitdata = NULL;
 
 static int __devinit
@@ -546,7 +546,7 @@
 	found = 0;
 	seekcard = PCI_DEVICE_ID_PLX_R685;
 	for (nbseek = 0; nbseek < 4; nbseek++) {
-		if ((dev_tel = pci_find_device(PCI_VENDOR_ID_PLX,
+		if ((dev_tel = hisax_find_pci_device(PCI_VENDOR_ID_PLX,
 					seekcard, dev_tel))) {
 			if (pci_enable_device(dev_tel))
 				return 1;
@@ -620,7 +620,7 @@
 
 	return (0);
 }
-#endif /* CONFIG_PCI_LEGACY */
+#endif /* CONFIG_PCI */
 
 int __devinit
 setup_gazel(struct IsdnCard *card)
@@ -640,7 +640,7 @@
 			return (0);
 	} else {
 
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 		if (setup_gazelpci(cs))
 			return (0);
 #else
diff --git a/drivers/isdn/hisax/hfc_pci.c b/drivers/isdn/hisax/hfc_pci.c
index 1091473..917cc84 100644
--- a/drivers/isdn/hisax/hfc_pci.c
+++ b/drivers/isdn/hisax/hfc_pci.c
@@ -1658,7 +1658,7 @@
 
 	i = 0;
 	while (id_list[i].vendor_id) {
-		tmp_hfcpci = pci_find_device(id_list[i].vendor_id,
+		tmp_hfcpci = hisax_find_pci_device(id_list[i].vendor_id,
 					     id_list[i].device_id,
 					     dev_hfcpci);
 		i++;
diff --git a/drivers/isdn/hisax/hisax.h b/drivers/isdn/hisax/hisax.h
index 0685c19..832a878 100644
--- a/drivers/isdn/hisax/hisax.h
+++ b/drivers/isdn/hisax/hisax.h
@@ -1323,3 +1323,26 @@
 char *HiSax_getrev(const char *revision);
 int TeiNew(void);
 void TeiFree(void);
+
+#ifdef CONFIG_PCI
+
+#include <linux/pci.h>
+
+/* adaptation wrapper for old usage
+ * WARNING! This is unfit for use in a PCI hotplug environment,
+ * as the returned PCI device can disappear at any moment in time.
+ * Callers should be converted to use pci_get_device() instead.
+ */
+static inline struct pci_dev *hisax_find_pci_device(unsigned int vendor,
+						    unsigned int device,
+						    struct pci_dev *from)
+{
+	struct pci_dev *pdev;
+
+	pci_dev_get(from);
+	pdev = pci_get_subsys(vendor, device, PCI_ANY_ID, PCI_ANY_ID, from);
+	pci_dev_put(pdev);
+	return pdev;
+}
+
+#endif
diff --git a/drivers/isdn/hisax/niccy.c b/drivers/isdn/hisax/niccy.c
index ef00633..ccaa6e1 100644
--- a/drivers/isdn/hisax/niccy.c
+++ b/drivers/isdn/hisax/niccy.c
@@ -297,12 +297,12 @@
 			return 0;
 		}
 	} else {
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 		static struct pci_dev *niccy_dev __devinitdata;
 
 		u_int pci_ioaddr;
 		cs->subtyp = 0;
-		if ((niccy_dev = pci_find_device(PCI_VENDOR_ID_SATSAGEM,
+		if ((niccy_dev = hisax_find_pci_device(PCI_VENDOR_ID_SATSAGEM,
 						 PCI_DEVICE_ID_SATSAGEM_NICCY,
 						 niccy_dev))) {
 			if (pci_enable_device(niccy_dev))
@@ -354,7 +354,7 @@
 		printk(KERN_WARNING "Niccy: io0 0 and NO_PCI_BIOS\n");
 		printk(KERN_WARNING "Niccy: unable to config NICCY PCI\n");
 		return 0;
-#endif				/* CONFIG_PCI_LEGACY */
+#endif				/* CONFIG_PCI */
 	}
 	printk(KERN_INFO "HiSax: NICCY %s config irq:%d data:0x%X ale:0x%X\n",
 		(cs->subtyp == 1) ? "PnP" : "PCI",
diff --git a/drivers/isdn/hisax/nj_s.c b/drivers/isdn/hisax/nj_s.c
index 8d36ccc..2344e7b 100644
--- a/drivers/isdn/hisax/nj_s.c
+++ b/drivers/isdn/hisax/nj_s.c
@@ -276,7 +276,7 @@
 
 	for ( ;; )
 	{
-		if ((dev_netjet = pci_find_device(PCI_VENDOR_ID_TIGERJET,
+		if ((dev_netjet = hisax_find_pci_device(PCI_VENDOR_ID_TIGERJET,
 			PCI_DEVICE_ID_TIGERJET_300,  dev_netjet))) {
 			ret = njs_pci_probe(dev_netjet, cs);
 			if (!ret)
diff --git a/drivers/isdn/hisax/nj_u.c b/drivers/isdn/hisax/nj_u.c
index d306c94..095e974 100644
--- a/drivers/isdn/hisax/nj_u.c
+++ b/drivers/isdn/hisax/nj_u.c
@@ -240,7 +240,7 @@
 
 	for ( ;; )
 	{
-		if ((dev_netjet = pci_find_device(PCI_VENDOR_ID_TIGERJET,
+		if ((dev_netjet = hisax_find_pci_device(PCI_VENDOR_ID_TIGERJET,
 			PCI_DEVICE_ID_TIGERJET_300,  dev_netjet))) {
 			ret = nju_pci_probe(dev_netjet, cs);
 			if (!ret)
diff --git a/drivers/isdn/hisax/sedlbauer.c b/drivers/isdn/hisax/sedlbauer.c
index 5569a52..69dfc8d 100644
--- a/drivers/isdn/hisax/sedlbauer.c
+++ b/drivers/isdn/hisax/sedlbauer.c
@@ -598,7 +598,7 @@
 }
 #endif /* __ISAPNP__ */
 
-#ifdef CONFIG_PCI_LEGACY
+#ifdef CONFIG_PCI
 static struct pci_dev *dev_sedl __devinitdata = NULL;
 
 static int __devinit
@@ -607,7 +607,7 @@
 	struct IsdnCardState *cs = card->cs;
 	u16 sub_vendor_id, sub_id;
 
-	if ((dev_sedl = pci_find_device(PCI_VENDOR_ID_TIGERJET,
+	if ((dev_sedl = hisax_find_pci_device(PCI_VENDOR_ID_TIGERJET,
 			PCI_DEVICE_ID_TIGERJET_100, dev_sedl))) {
 		if (pci_enable_device(dev_sedl))
 			return(0);
@@ -673,7 +673,7 @@
 	return (1);
 }
 
-#endif /* CONFIG_PCI_LEGACY */
+#endif /* CONFIG_PCI */
 
 int __devinit
 setup_sedlbauer(struct IsdnCard *card)
diff --git a/drivers/isdn/hisax/telespci.c b/drivers/isdn/hisax/telespci.c
index 28b08de..b85ceb3 100644
--- a/drivers/isdn/hisax/telespci.c
+++ b/drivers/isdn/hisax/telespci.c
@@ -300,7 +300,7 @@
 	if (cs->typ != ISDN_CTYPE_TELESPCI)
 		return (0);
 
-	if ((dev_tel = pci_find_device (PCI_VENDOR_ID_ZORAN, PCI_DEVICE_ID_ZORAN_36120, dev_tel))) {
+	if ((dev_tel = hisax_find_pci_device (PCI_VENDOR_ID_ZORAN, PCI_DEVICE_ID_ZORAN_36120, dev_tel))) {
 		if (pci_enable_device(dev_tel))
 			return(0);
 		cs->irq = dev_tel->irq;
diff --git a/drivers/isdn/hisax/w6692.c b/drivers/isdn/hisax/w6692.c
index c4d862c..9d6e864 100644
--- a/drivers/isdn/hisax/w6692.c
+++ b/drivers/isdn/hisax/w6692.c
@@ -1007,7 +1007,7 @@
 		return (0);
 
 	while (id_list[id_idx].vendor_id) {
-		dev_w6692 = pci_find_device(id_list[id_idx].vendor_id,
+		dev_w6692 = hisax_find_pci_device(id_list[id_idx].vendor_id,
 					    id_list[id_idx].device_id,
 					    dev_w6692);
 		if (dev_w6692) {
diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index b1ecefa..7858a11 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -21,17 +21,6 @@
 
 	   If you don't know what to do here, say N.
 
-config PCI_LEGACY
-	bool "Enable deprecated pci_find_* API"
-	depends on PCI
-	default y
-	help
-	  Say Y here if you want to include support for the deprecated
-	  pci_find_device() API.  Most drivers have been converted over
-	  to using the proper hotplug APIs, so this option serves to
-	  include/exclude only a few drivers that are still using this
-	  API.
-
 config PCI_DEBUG
 	bool "PCI Debugging"
 	depends on PCI && DEBUG_KERNEL
diff --git a/drivers/pci/Makefile b/drivers/pci/Makefile
index 4df48d5..8674c1e 100644
--- a/drivers/pci/Makefile
+++ b/drivers/pci/Makefile
@@ -2,14 +2,13 @@
 # Makefile for the PCI bus specific drivers.
 #
 
-obj-y		+= access.o bus.o probe.o remove.o pci.o quirks.o \
+obj-y		+= access.o bus.o probe.o remove.o pci.o \
 			pci-driver.o search.o pci-sysfs.o rom.o setup-res.o \
 			irq.o
 obj-$(CONFIG_PROC_FS) += proc.o
 obj-$(CONFIG_SYSFS) += slot.o
 
-obj-$(CONFIG_PCI_LEGACY) += legacy.o
-CFLAGS_legacy.o += -Wno-deprecated-declarations
+obj-$(CONFIG_PCI_QUIRKS) += quirks.o
 
 # Build PCI Express stuff if needed
 obj-$(CONFIG_PCIEPORTBUS) += pcie/
diff --git a/drivers/pci/bus.c b/drivers/pci/bus.c
index cef28a7..712250f 100644
--- a/drivers/pci/bus.c
+++ b/drivers/pci/bus.c
@@ -17,6 +17,52 @@
 
 #include "pci.h"
 
+void pci_bus_add_resource(struct pci_bus *bus, struct resource *res,
+			  unsigned int flags)
+{
+	struct pci_bus_resource *bus_res;
+
+	bus_res = kzalloc(sizeof(struct pci_bus_resource), GFP_KERNEL);
+	if (!bus_res) {
+		dev_err(&bus->dev, "can't add %pR resource\n", res);
+		return;
+	}
+
+	bus_res->res = res;
+	bus_res->flags = flags;
+	list_add_tail(&bus_res->list, &bus->resources);
+}
+
+struct resource *pci_bus_resource_n(const struct pci_bus *bus, int n)
+{
+	struct pci_bus_resource *bus_res;
+
+	if (n < PCI_BRIDGE_RESOURCE_NUM)
+		return bus->resource[n];
+
+	n -= PCI_BRIDGE_RESOURCE_NUM;
+	list_for_each_entry(bus_res, &bus->resources, list) {
+		if (n-- == 0)
+			return bus_res->res;
+	}
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(pci_bus_resource_n);
+
+void pci_bus_remove_resources(struct pci_bus *bus)
+{
+	struct pci_bus_resource *bus_res, *tmp;
+	int i;
+
+	for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; i++)
+		bus->resource[i] = 0;
+
+	list_for_each_entry_safe(bus_res, tmp, &bus->resources, list) {
+		list_del(&bus_res->list);
+		kfree(bus_res);
+	}
+}
+
 /**
  * pci_bus_alloc_resource - allocate a resource from a parent bus
  * @bus: PCI bus
@@ -36,11 +82,14 @@
 pci_bus_alloc_resource(struct pci_bus *bus, struct resource *res,
 		resource_size_t size, resource_size_t align,
 		resource_size_t min, unsigned int type_mask,
-		void (*alignf)(void *, struct resource *, resource_size_t,
-				resource_size_t),
+		resource_size_t (*alignf)(void *,
+					  const struct resource *,
+					  resource_size_t,
+					  resource_size_t),
 		void *alignf_data)
 {
 	int i, ret = -ENOMEM;
+	struct resource *r;
 	resource_size_t max = -1;
 
 	type_mask |= IORESOURCE_IO | IORESOURCE_MEM;
@@ -49,8 +98,7 @@
 	if (!(res->flags & IORESOURCE_MEM_64))
 		max = PCIBIOS_MAX_MEM_32;
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		struct resource *r = bus->resource[i];
+	pci_bus_for_each_resource(bus, r, i) {
 		if (!r)
 			continue;
 
diff --git a/drivers/pci/hotplug/acpiphp_core.c b/drivers/pci/hotplug/acpiphp_core.c
index 4dd7114..efa9f2d 100644
--- a/drivers/pci/hotplug/acpiphp_core.c
+++ b/drivers/pci/hotplug/acpiphp_core.c
@@ -332,8 +332,6 @@
 	slot->hotplug_slot->info->attention_status = 0;
 	slot->hotplug_slot->info->latch_status = acpiphp_get_latch_status(slot->acpi_slot);
 	slot->hotplug_slot->info->adapter_status = acpiphp_get_adapter_status(slot->acpi_slot);
-	slot->hotplug_slot->info->max_bus_speed = PCI_SPEED_UNKNOWN;
-	slot->hotplug_slot->info->cur_bus_speed = PCI_SPEED_UNKNOWN;
 
 	acpiphp_slot->slot = slot;
 	snprintf(name, SLOT_NAME_SIZE, "%llu", slot->acpi_slot->sun);
diff --git a/drivers/pci/hotplug/cpcihp_generic.c b/drivers/pci/hotplug/cpcihp_generic.c
index 148fb46..fb3f846 100644
--- a/drivers/pci/hotplug/cpcihp_generic.c
+++ b/drivers/pci/hotplug/cpcihp_generic.c
@@ -162,6 +162,7 @@
 	dev = pci_get_slot(bus, PCI_DEVFN(bridge_slot, 0));
 	if(!dev || dev->hdr_type != PCI_HEADER_TYPE_BRIDGE) {
 		err("Invalid bridge device %s", bridge);
+		pci_dev_put(dev);
 		return -EINVAL;
 	}
 	bus = dev->subordinate;
diff --git a/drivers/pci/hotplug/cpqphp.h b/drivers/pci/hotplug/cpqphp.h
index 9c6a9fd..d8ffc73 100644
--- a/drivers/pci/hotplug/cpqphp.h
+++ b/drivers/pci/hotplug/cpqphp.h
@@ -310,8 +310,6 @@
 	u8 first_slot;
 	u8 add_support;
 	u8 push_flag;
-	enum pci_bus_speed speed;
-	enum pci_bus_speed speed_capability;
 	u8 push_button;			/* 0 = no pushbutton, 1 = pushbutton present */
 	u8 slot_switch_type;		/* 0 = no switch, 1 = switch present */
 	u8 defeature_PHP;		/* 0 = PHP not supported, 1 = PHP supported */
diff --git a/drivers/pci/hotplug/cpqphp_core.c b/drivers/pci/hotplug/cpqphp_core.c
index 075b4f4..f184d1d 100644
--- a/drivers/pci/hotplug/cpqphp_core.c
+++ b/drivers/pci/hotplug/cpqphp_core.c
@@ -583,30 +583,6 @@
 	return 0;
 }
 
-static int get_max_bus_speed (struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
-{
-	struct slot *slot = hotplug_slot->private;
-	struct controller *ctrl = slot->ctrl;
-
-	dbg("%s - physical_slot = %s\n", __func__, slot_name(slot));
-
-	*value = ctrl->speed_capability;
-
-	return 0;
-}
-
-static int get_cur_bus_speed (struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
-{
-	struct slot *slot = hotplug_slot->private;
-	struct controller *ctrl = slot->ctrl;
-
-	dbg("%s - physical_slot = %s\n", __func__, slot_name(slot));
-
-	*value = ctrl->speed;
-
-	return 0;
-}
-
 static struct hotplug_slot_ops cpqphp_hotplug_slot_ops = {
 	.set_attention_status =	set_attention_status,
 	.enable_slot =		process_SI,
@@ -616,8 +592,6 @@
 	.get_attention_status =	get_attention_status,
 	.get_latch_status =	get_latch_status,
 	.get_adapter_status =	get_adapter_status,
-	.get_max_bus_speed =	get_max_bus_speed,
-	.get_cur_bus_speed =	get_cur_bus_speed,
 };
 
 #define SLOT_NAME_SIZE 10
@@ -629,6 +603,7 @@
 	struct slot *slot;
 	struct hotplug_slot *hotplug_slot;
 	struct hotplug_slot_info *hotplug_slot_info;
+	struct pci_bus *bus = ctrl->pci_bus;
 	u8 number_of_slots;
 	u8 slot_device;
 	u8 slot_number;
@@ -694,7 +669,7 @@
 			slot->capabilities |= PCISLOT_64_BIT_SUPPORTED;
 		if (is_slot66mhz(slot))
 			slot->capabilities |= PCISLOT_66_MHZ_SUPPORTED;
-		if (ctrl->speed == PCI_SPEED_66MHz)
+		if (bus->cur_bus_speed == PCI_SPEED_66MHz)
 			slot->capabilities |= PCISLOT_66_MHZ_OPERATION;
 
 		ctrl_slot =
@@ -844,6 +819,7 @@
 	u32 rc;
 	struct controller *ctrl;
 	struct pci_func *func;
+	struct pci_bus *bus;
 	int err;
 
 	err = pci_enable_device(pdev);
@@ -852,6 +828,7 @@
 			pci_name(pdev), err);
 		return err;
 	}
+	bus = pdev->subordinate;
 
 	/* Need to read VID early b/c it's used to differentiate CPQ and INTC
 	 * discovery
@@ -929,22 +906,22 @@
 			pci_read_config_byte(pdev, 0x41, &bus_cap);
 			if (bus_cap & 0x80) {
 				dbg("bus max supports 133MHz PCI-X\n");
-				ctrl->speed_capability = PCI_SPEED_133MHz_PCIX;
+				bus->max_bus_speed = PCI_SPEED_133MHz_PCIX;
 				break;
 			}
 			if (bus_cap & 0x40) {
 				dbg("bus max supports 100MHz PCI-X\n");
-				ctrl->speed_capability = PCI_SPEED_100MHz_PCIX;
+				bus->max_bus_speed = PCI_SPEED_100MHz_PCIX;
 				break;
 			}
 			if (bus_cap & 20) {
 				dbg("bus max supports 66MHz PCI-X\n");
-				ctrl->speed_capability = PCI_SPEED_66MHz_PCIX;
+				bus->max_bus_speed = PCI_SPEED_66MHz_PCIX;
 				break;
 			}
 			if (bus_cap & 10) {
 				dbg("bus max supports 66MHz PCI\n");
-				ctrl->speed_capability = PCI_SPEED_66MHz;
+				bus->max_bus_speed = PCI_SPEED_66MHz;
 				break;
 			}
 
@@ -955,7 +932,7 @@
 		case PCI_SUB_HPC_ID:
 			/* Original 6500/7000 implementation */
 			ctrl->slot_switch_type = 1;
-			ctrl->speed_capability = PCI_SPEED_33MHz;
+			bus->max_bus_speed = PCI_SPEED_33MHz;
 			ctrl->push_button = 0;
 			ctrl->pci_config_space = 1;
 			ctrl->defeature_PHP = 1;
@@ -966,7 +943,7 @@
 			/* First Pushbutton implementation */
 			ctrl->push_flag = 1;
 			ctrl->slot_switch_type = 1;
-			ctrl->speed_capability = PCI_SPEED_33MHz;
+			bus->max_bus_speed = PCI_SPEED_33MHz;
 			ctrl->push_button = 1;
 			ctrl->pci_config_space = 1;
 			ctrl->defeature_PHP = 1;
@@ -976,7 +953,7 @@
 		case PCI_SUB_HPC_ID_INTC:
 			/* Third party (6500/7000) */
 			ctrl->slot_switch_type = 1;
-			ctrl->speed_capability = PCI_SPEED_33MHz;
+			bus->max_bus_speed = PCI_SPEED_33MHz;
 			ctrl->push_button = 0;
 			ctrl->pci_config_space = 1;
 			ctrl->defeature_PHP = 1;
@@ -987,7 +964,7 @@
 			/* First 66 Mhz implementation */
 			ctrl->push_flag = 1;
 			ctrl->slot_switch_type = 1;
-			ctrl->speed_capability = PCI_SPEED_66MHz;
+			bus->max_bus_speed = PCI_SPEED_66MHz;
 			ctrl->push_button = 1;
 			ctrl->pci_config_space = 1;
 			ctrl->defeature_PHP = 1;
@@ -998,7 +975,7 @@
 			/* First PCI-X implementation, 100MHz */
 			ctrl->push_flag = 1;
 			ctrl->slot_switch_type = 1;
-			ctrl->speed_capability = PCI_SPEED_100MHz_PCIX;
+			bus->max_bus_speed = PCI_SPEED_100MHz_PCIX;
 			ctrl->push_button = 1;
 			ctrl->pci_config_space = 1;
 			ctrl->defeature_PHP = 1;
@@ -1015,9 +992,9 @@
 	case PCI_VENDOR_ID_INTEL:
 		/* Check for speed capability (0=33, 1=66) */
 		if (subsystem_deviceid & 0x0001)
-			ctrl->speed_capability = PCI_SPEED_66MHz;
+			bus->max_bus_speed = PCI_SPEED_66MHz;
 		else
-			ctrl->speed_capability = PCI_SPEED_33MHz;
+			bus->max_bus_speed = PCI_SPEED_33MHz;
 
 		/* Check for push button */
 		if (subsystem_deviceid & 0x0002)
@@ -1079,7 +1056,7 @@
 					pdev->bus->number);
 
 	dbg("Hotplug controller capabilities:\n");
-	dbg("    speed_capability       %d\n", ctrl->speed_capability);
+	dbg("    speed_capability       %d\n", bus->max_bus_speed);
 	dbg("    slot_switch_type       %s\n", ctrl->slot_switch_type ?
 					"switch present" : "no switch");
 	dbg("    defeature_PHP          %s\n", ctrl->defeature_PHP ?
@@ -1142,7 +1119,7 @@
 	}
 
 	/* Check for 66Mhz operation */
-	ctrl->speed = get_controller_speed(ctrl);
+	bus->cur_bus_speed = get_controller_speed(ctrl);
 
 
 	/********************************************************
diff --git a/drivers/pci/hotplug/cpqphp_ctrl.c b/drivers/pci/hotplug/cpqphp_ctrl.c
index 0ff689a..e43908d 100644
--- a/drivers/pci/hotplug/cpqphp_ctrl.c
+++ b/drivers/pci/hotplug/cpqphp_ctrl.c
@@ -1130,12 +1130,13 @@
 static u8 set_controller_speed(struct controller *ctrl, u8 adapter_speed, u8 hp_slot)
 {
 	struct slot *slot;
+	struct pci_bus *bus = ctrl->pci_bus;
 	u8 reg;
 	u8 slot_power = readb(ctrl->hpc_reg + SLOT_POWER);
 	u16 reg16;
 	u32 leds = readl(ctrl->hpc_reg + LED_CONTROL);
 
-	if (ctrl->speed == adapter_speed)
+	if (bus->cur_bus_speed == adapter_speed)
 		return 0;
 
 	/* We don't allow freq/mode changes if we find another adapter running
@@ -1152,7 +1153,7 @@
 		 * lower speed/mode, we allow the new adapter to function at
 		 * this rate if supported
 		 */
-		if (ctrl->speed < adapter_speed)
+		if (bus->cur_bus_speed < adapter_speed)
 			return 0;
 
 		return 1;
@@ -1161,20 +1162,20 @@
 	/* If the controller doesn't support freq/mode changes and the
 	 * controller is running at a higher mode, we bail
 	 */
-	if ((ctrl->speed > adapter_speed) && (!ctrl->pcix_speed_capability))
+	if ((bus->cur_bus_speed > adapter_speed) && (!ctrl->pcix_speed_capability))
 		return 1;
 
 	/* But we allow the adapter to run at a lower rate if possible */
-	if ((ctrl->speed < adapter_speed) && (!ctrl->pcix_speed_capability))
+	if ((bus->cur_bus_speed < adapter_speed) && (!ctrl->pcix_speed_capability))
 		return 0;
 
 	/* We try to set the max speed supported by both the adapter and
 	 * controller
 	 */
-	if (ctrl->speed_capability < adapter_speed) {
-		if (ctrl->speed == ctrl->speed_capability)
+	if (bus->max_bus_speed < adapter_speed) {
+		if (bus->cur_bus_speed == bus->max_bus_speed)
 			return 0;
-		adapter_speed = ctrl->speed_capability;
+		adapter_speed = bus->max_bus_speed;
 	}
 
 	writel(0x0L, ctrl->hpc_reg + LED_CONTROL);
@@ -1229,8 +1230,8 @@
 	pci_write_config_byte(ctrl->pci_dev, 0x43, reg);
 
 	/* Only if mode change...*/
-	if (((ctrl->speed == PCI_SPEED_66MHz) && (adapter_speed == PCI_SPEED_66MHz_PCIX)) ||
-		((ctrl->speed == PCI_SPEED_66MHz_PCIX) && (adapter_speed == PCI_SPEED_66MHz))) 
+	if (((bus->cur_bus_speed == PCI_SPEED_66MHz) && (adapter_speed == PCI_SPEED_66MHz_PCIX)) ||
+		((bus->cur_bus_speed == PCI_SPEED_66MHz_PCIX) && (adapter_speed == PCI_SPEED_66MHz))) 
 			set_SOGO(ctrl);
 
 	wait_for_ctrl_irq(ctrl);
@@ -1243,7 +1244,7 @@
 	set_SOGO(ctrl);
 	wait_for_ctrl_irq(ctrl);
 
-	ctrl->speed = adapter_speed;
+	bus->cur_bus_speed = adapter_speed;
 	slot = cpqhp_find_slot(ctrl, hp_slot + ctrl->slot_device_offset);
 
 	info("Successfully changed frequency/mode for adapter in slot %d\n",
@@ -1269,6 +1270,7 @@
  */
 static u32 board_replaced(struct pci_func *func, struct controller *ctrl)
 {
+	struct pci_bus *bus = ctrl->pci_bus;
 	u8 hp_slot;
 	u8 temp_byte;
 	u8 adapter_speed;
@@ -1309,7 +1311,7 @@
 		wait_for_ctrl_irq (ctrl);
 
 		adapter_speed = get_adapter_speed(ctrl, hp_slot);
-		if (ctrl->speed != adapter_speed)
+		if (bus->cur_bus_speed != adapter_speed)
 			if (set_controller_speed(ctrl, adapter_speed, hp_slot))
 				rc = WRONG_BUS_FREQUENCY;
 
@@ -1426,6 +1428,7 @@
 	u32 temp_register = 0xFFFFFFFF;
 	u32 rc = 0;
 	struct pci_func *new_slot = NULL;
+	struct pci_bus *bus = ctrl->pci_bus;
 	struct slot *p_slot;
 	struct resource_lists res_lists;
 
@@ -1456,7 +1459,7 @@
 	wait_for_ctrl_irq (ctrl);
 
 	adapter_speed = get_adapter_speed(ctrl, hp_slot);
-	if (ctrl->speed != adapter_speed)
+	if (bus->cur_bus_speed != adapter_speed)
 		if (set_controller_speed(ctrl, adapter_speed, hp_slot))
 			rc = WRONG_BUS_FREQUENCY;
 
diff --git a/drivers/pci/hotplug/ibmphp_core.c b/drivers/pci/hotplug/ibmphp_core.c
index 7485ffd..d934dd4 100644
--- a/drivers/pci/hotplug/ibmphp_core.c
+++ b/drivers/pci/hotplug/ibmphp_core.c
@@ -395,89 +395,40 @@
 	return rc;
 }
 
-static int get_max_bus_speed(struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
+static int get_max_bus_speed(struct slot *slot)
 {
-	int rc = -ENODEV;
-	struct slot *pslot;
+	int rc;
 	u8 mode = 0;
+	enum pci_bus_speed speed;
+	struct pci_bus *bus = slot->hotplug_slot->pci_slot->bus;
 
-	debug("%s - Entry hotplug_slot[%p] pvalue[%p]\n", __func__,
-		hotplug_slot, value);
+	debug("%s - Entry slot[%p]\n", __func__, slot);
 
 	ibmphp_lock_operations();
+	mode = slot->supported_bus_mode;
+	speed = slot->supported_speed; 
+	ibmphp_unlock_operations();
 
-	if (hotplug_slot) {
-		pslot = hotplug_slot->private;
-		if (pslot) {
-			rc = 0;
-			mode = pslot->supported_bus_mode;
-			*value = pslot->supported_speed; 
-			switch (*value) {
-			case BUS_SPEED_33:
-				break;
-			case BUS_SPEED_66:
-				if (mode == BUS_MODE_PCIX) 
-					*value += 0x01;
-				break;
-			case BUS_SPEED_100:
-			case BUS_SPEED_133:
-				*value = pslot->supported_speed + 0x01;
-				break;
-			default:
-				/* Note (will need to change): there would be soon 256, 512 also */
-				rc = -ENODEV;
-			}
-		}
+	switch (speed) {
+	case BUS_SPEED_33:
+		break;
+	case BUS_SPEED_66:
+		if (mode == BUS_MODE_PCIX) 
+			speed += 0x01;
+		break;
+	case BUS_SPEED_100:
+	case BUS_SPEED_133:
+		speed += 0x01;
+		break;
+	default:
+		/* Note (will need to change): there would be soon 256, 512 also */
+		rc = -ENODEV;
 	}
 
-	ibmphp_unlock_operations();
-	debug("%s - Exit rc[%d] value[%x]\n", __func__, rc, *value);
-	return rc;
-}
+	if (!rc)
+		bus->max_bus_speed = speed;
 
-static int get_cur_bus_speed(struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
-{
-	int rc = -ENODEV;
-	struct slot *pslot;
-	u8 mode = 0;
-
-	debug("%s - Entry hotplug_slot[%p] pvalue[%p]\n", __func__,
-		hotplug_slot, value);
-
-	ibmphp_lock_operations();
-
-	if (hotplug_slot) {
-		pslot = hotplug_slot->private;
-		if (pslot) {
-			rc = get_cur_bus_info(&pslot);
-			if (!rc) {
-				mode = pslot->bus_on->current_bus_mode;
-				*value = pslot->bus_on->current_speed;
-				switch (*value) {
-				case BUS_SPEED_33:
-					break;
-				case BUS_SPEED_66:
-					if (mode == BUS_MODE_PCIX) 
-						*value += 0x01;
-					else if (mode == BUS_MODE_PCI)
-						;
-					else
-						*value = PCI_SPEED_UNKNOWN;
-					break;
-				case BUS_SPEED_100:
-				case BUS_SPEED_133:
-					*value += 0x01;
-					break;
-				default:
-					/* Note of change: there would also be 256, 512 soon */
-					rc = -ENODEV;
-				}
-			}
-		}
-	}
-
-	ibmphp_unlock_operations();
-	debug("%s - Exit rc[%d] value[%x]\n", __func__, rc, *value);
+	debug("%s - Exit rc[%d] speed[%x]\n", __func__, rc, speed);
 	return rc;
 }
 
@@ -572,6 +523,7 @@
 		if (slot_cur->bus_on->current_speed == 0xFF) 
 			if (get_cur_bus_info(&slot_cur)) 
 				return -1;
+		get_max_bus_speed(slot_cur);
 
 		if (slot_cur->ctrl->options == 0xFF)
 			if (get_hpc_options(slot_cur, &slot_cur->ctrl->options))
@@ -655,6 +607,7 @@
 int ibmphp_update_slot_info(struct slot *slot_cur)
 {
 	struct hotplug_slot_info *info;
+	struct pci_bus *bus = slot_cur->hotplug_slot->pci_slot->bus;
 	int rc;
 	u8 bus_speed;
 	u8 mode;
@@ -700,8 +653,7 @@
 			bus_speed = PCI_SPEED_UNKNOWN;
 	}
 
-	info->cur_bus_speed = bus_speed;
-	info->max_bus_speed = slot_cur->hotplug_slot->info->max_bus_speed;
+	bus->cur_bus_speed = bus_speed;
 	// To do: bus_names 
 	
 	rc = pci_hp_change_slot_info(slot_cur->hotplug_slot, info);
@@ -1326,8 +1278,6 @@
 	.get_attention_status =		get_attention_status,
 	.get_latch_status =		get_latch_status,
 	.get_adapter_status =		get_adapter_present,
-	.get_max_bus_speed =		get_max_bus_speed,
-	.get_cur_bus_speed =		get_cur_bus_speed,
 /*	.get_max_adapter_speed =	get_max_adapter_speed,
 	.get_bus_name_status =		get_bus_name,
 */
diff --git a/drivers/pci/hotplug/ibmphp_ebda.c b/drivers/pci/hotplug/ibmphp_ebda.c
index c1abac8..5becbde 100644
--- a/drivers/pci/hotplug/ibmphp_ebda.c
+++ b/drivers/pci/hotplug/ibmphp_ebda.c
@@ -245,7 +245,7 @@
 
 int __init ibmphp_access_ebda (void)
 {
-	u8 format, num_ctlrs, rio_complete, hs_complete;
+	u8 format, num_ctlrs, rio_complete, hs_complete, ebda_sz;
 	u16 ebda_seg, num_entries, next_offset, offset, blk_id, sub_addr, re, rc_id, re_id, base;
 	int rc = 0;
 
@@ -260,7 +260,16 @@
 	iounmap (io_mem);
 	debug ("returned ebda segment: %x\n", ebda_seg);
 	
-	io_mem = ioremap(ebda_seg<<4, 1024);
+	io_mem = ioremap(ebda_seg<<4, 1);
+	if (!io_mem)
+		return -ENOMEM;
+	ebda_sz = readb(io_mem);
+	iounmap(io_mem);
+	debug("ebda size: %d(KiB)\n", ebda_sz);
+	if (ebda_sz == 0)
+		return -ENOMEM;
+
+	io_mem = ioremap(ebda_seg<<4, (ebda_sz * 1024));
 	if (!io_mem )
 		return -ENOMEM;
 	next_offset = 0x180;
diff --git a/drivers/pci/hotplug/ibmphp_hpc.c b/drivers/pci/hotplug/ibmphp_hpc.c
index c7084f0..1aaf3f3 100644
--- a/drivers/pci/hotplug/ibmphp_hpc.c
+++ b/drivers/pci/hotplug/ibmphp_hpc.c
@@ -35,6 +35,7 @@
 #include <linux/init.h>
 #include <linux/mutex.h>
 #include <linux/sched.h>
+#include <linux/semaphore.h>
 #include <linux/kthread.h>
 #include "ibmphp.h"
 
diff --git a/drivers/pci/hotplug/pci_hotplug_core.c b/drivers/pci/hotplug/pci_hotplug_core.c
index 38183a5..728b119 100644
--- a/drivers/pci/hotplug/pci_hotplug_core.c
+++ b/drivers/pci/hotplug/pci_hotplug_core.c
@@ -64,32 +64,6 @@
 static LIST_HEAD(pci_hotplug_slot_list);
 static DEFINE_MUTEX(pci_hp_mutex);
 
-/* these strings match up with the values in pci_bus_speed */
-static char *pci_bus_speed_strings[] = {
-	"33 MHz PCI",		/* 0x00 */
-	"66 MHz PCI",		/* 0x01 */
-	"66 MHz PCI-X",		/* 0x02 */
-	"100 MHz PCI-X",	/* 0x03 */
-	"133 MHz PCI-X",	/* 0x04 */
-	NULL,			/* 0x05 */
-	NULL,			/* 0x06 */
-	NULL,			/* 0x07 */
-	NULL,			/* 0x08 */
-	"66 MHz PCI-X 266",	/* 0x09 */
-	"100 MHz PCI-X 266",	/* 0x0a */
-	"133 MHz PCI-X 266",	/* 0x0b */
-	NULL,			/* 0x0c */
-	NULL,			/* 0x0d */
-	NULL,			/* 0x0e */
-	NULL,			/* 0x0f */
-	NULL,			/* 0x10 */
-	"66 MHz PCI-X 533",	/* 0x11 */
-	"100 MHz PCI-X 533",	/* 0x12 */
-	"133 MHz PCI-X 533",	/* 0x13 */
-	"2.5 GT/s PCIe",	/* 0x14 */
-	"5.0 GT/s PCIe",	/* 0x15 */
-};
-
 #ifdef CONFIG_HOTPLUG_PCI_CPCI
 extern int cpci_hotplug_init(int debug);
 extern void cpci_hotplug_exit(void);
@@ -118,8 +92,6 @@
 GET_STATUS(attention_status, u8)
 GET_STATUS(latch_status, u8)
 GET_STATUS(adapter_status, u8)
-GET_STATUS(max_bus_speed, enum pci_bus_speed)
-GET_STATUS(cur_bus_speed, enum pci_bus_speed)
 
 static ssize_t power_read_file(struct pci_slot *slot, char *buf)
 {
@@ -263,60 +235,6 @@
 	.show = presence_read_file,
 };
 
-static char *unknown_speed = "Unknown bus speed";
-
-static ssize_t max_bus_speed_read_file(struct pci_slot *slot, char *buf)
-{
-	char *speed_string;
-	int retval;
-	enum pci_bus_speed value;
-	
-	retval = get_max_bus_speed(slot->hotplug, &value);
-	if (retval)
-		goto exit;
-
-	if (value == PCI_SPEED_UNKNOWN)
-		speed_string = unknown_speed;
-	else
-		speed_string = pci_bus_speed_strings[value];
-	
-	retval = sprintf (buf, "%s\n", speed_string);
-
-exit:
-	return retval;
-}
-
-static struct pci_slot_attribute hotplug_slot_attr_max_bus_speed = {
-	.attr = {.name = "max_bus_speed", .mode = S_IFREG | S_IRUGO},
-	.show = max_bus_speed_read_file,
-};
-
-static ssize_t cur_bus_speed_read_file(struct pci_slot *slot, char *buf)
-{
-	char *speed_string;
-	int retval;
-	enum pci_bus_speed value;
-
-	retval = get_cur_bus_speed(slot->hotplug, &value);
-	if (retval)
-		goto exit;
-
-	if (value == PCI_SPEED_UNKNOWN)
-		speed_string = unknown_speed;
-	else
-		speed_string = pci_bus_speed_strings[value];
-	
-	retval = sprintf (buf, "%s\n", speed_string);
-
-exit:
-	return retval;
-}
-
-static struct pci_slot_attribute hotplug_slot_attr_cur_bus_speed = {
-	.attr = {.name = "cur_bus_speed", .mode = S_IFREG | S_IRUGO},
-	.show = cur_bus_speed_read_file,
-};
-
 static ssize_t test_write_file(struct pci_slot *pci_slot, const char *buf,
 		size_t count)
 {
@@ -391,26 +309,6 @@
 	return false;
 }
 
-static bool has_max_bus_speed_file(struct pci_slot *pci_slot)
-{
-	struct hotplug_slot *slot = pci_slot->hotplug;
-	if ((!slot) || (!slot->ops))
-		return false;
-	if (slot->ops->get_max_bus_speed)
-		return true;
-	return false;
-}
-
-static bool has_cur_bus_speed_file(struct pci_slot *pci_slot)
-{
-	struct hotplug_slot *slot = pci_slot->hotplug;
-	if ((!slot) || (!slot->ops))
-		return false;
-	if (slot->ops->get_cur_bus_speed)
-		return true;
-	return false;
-}
-
 static bool has_test_file(struct pci_slot *pci_slot)
 {
 	struct hotplug_slot *slot = pci_slot->hotplug;
@@ -456,20 +354,6 @@
 			goto exit_adapter;
 	}
 
-	if (has_max_bus_speed_file(slot)) {
-		retval = sysfs_create_file(&slot->kobj,
-					&hotplug_slot_attr_max_bus_speed.attr);
-		if (retval)
-			goto exit_max_speed;
-	}
-
-	if (has_cur_bus_speed_file(slot)) {
-		retval = sysfs_create_file(&slot->kobj,
-					&hotplug_slot_attr_cur_bus_speed.attr);
-		if (retval)
-			goto exit_cur_speed;
-	}
-
 	if (has_test_file(slot)) {
 		retval = sysfs_create_file(&slot->kobj,
 					   &hotplug_slot_attr_test.attr);
@@ -480,14 +364,6 @@
 	goto exit;
 
 exit_test:
-	if (has_cur_bus_speed_file(slot))
-		sysfs_remove_file(&slot->kobj,
-				  &hotplug_slot_attr_cur_bus_speed.attr);
-exit_cur_speed:
-	if (has_max_bus_speed_file(slot))
-		sysfs_remove_file(&slot->kobj,
-				  &hotplug_slot_attr_max_bus_speed.attr);
-exit_max_speed:
 	if (has_adapter_file(slot))
 		sysfs_remove_file(&slot->kobj,
 				  &hotplug_slot_attr_presence.attr);
@@ -523,14 +399,6 @@
 		sysfs_remove_file(&slot->kobj,
 				  &hotplug_slot_attr_presence.attr);
 
-	if (has_max_bus_speed_file(slot))
-		sysfs_remove_file(&slot->kobj,
-				  &hotplug_slot_attr_max_bus_speed.attr);
-
-	if (has_cur_bus_speed_file(slot))
-		sysfs_remove_file(&slot->kobj,
-				  &hotplug_slot_attr_cur_bus_speed.attr);
-
 	if (has_test_file(slot))
 		sysfs_remove_file(&slot->kobj, &hotplug_slot_attr_test.attr);
 
diff --git a/drivers/pci/hotplug/pciehp_core.c b/drivers/pci/hotplug/pciehp_core.c
index 5674b20..920f820 100644
--- a/drivers/pci/hotplug/pciehp_core.c
+++ b/drivers/pci/hotplug/pciehp_core.c
@@ -69,8 +69,6 @@
 static int get_attention_status	(struct hotplug_slot *slot, u8 *value);
 static int get_latch_status	(struct hotplug_slot *slot, u8 *value);
 static int get_adapter_status	(struct hotplug_slot *slot, u8 *value);
-static int get_max_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
-static int get_cur_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
 
 /**
  * release_slot - free up the memory used by a slot
@@ -113,8 +111,6 @@
 	ops->disable_slot = disable_slot;
 	ops->get_power_status = get_power_status;
 	ops->get_adapter_status = get_adapter_status;
-	ops->get_max_bus_speed = get_max_bus_speed;
-	ops->get_cur_bus_speed = get_cur_bus_speed;
 	if (MRL_SENS(ctrl))
 		ops->get_latch_status = get_latch_status;
 	if (ATTN_LED(ctrl)) {
@@ -227,27 +223,6 @@
 	return pciehp_get_adapter_status(slot, value);
 }
 
-static int get_max_bus_speed(struct hotplug_slot *hotplug_slot,
-				enum pci_bus_speed *value)
-{
-	struct slot *slot = hotplug_slot->private;
-
-	ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
-		 __func__, slot_name(slot));
-
-	return pciehp_get_max_link_speed(slot, value);
-}
-
-static int get_cur_bus_speed(struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
-{
-	struct slot *slot = hotplug_slot->private;
-
-	ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
-		 __func__, slot_name(slot));
-
-	return pciehp_get_cur_link_speed(slot, value);
-}
-
 static int pciehp_probe(struct pcie_device *dev)
 {
 	int rc;
diff --git a/drivers/pci/hotplug/pciehp_ctrl.c b/drivers/pci/hotplug/pciehp_ctrl.c
index d6ac1b2..9a7f247 100644
--- a/drivers/pci/hotplug/pciehp_ctrl.c
+++ b/drivers/pci/hotplug/pciehp_ctrl.c
@@ -341,6 +341,7 @@
 		p_slot->state = POWERON_STATE;
 		break;
 	default:
+		kfree(info);
 		goto out;
 	}
 	queue_work(pciehp_wq, &info->work);
diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c
index 10040d5..40b48f5 100644
--- a/drivers/pci/hotplug/pciehp_hpc.c
+++ b/drivers/pci/hotplug/pciehp_hpc.c
@@ -492,6 +492,7 @@
 	u16 slot_cmd;
 	u16 cmd_mask;
 	u16 slot_status;
+	u16 lnk_status;
 	int retval = 0;
 
 	/* Clear sticky power-fault bit from previous power failures */
@@ -523,6 +524,14 @@
 	ctrl_dbg(ctrl, "%s: SLOTCTRL %x write cmd %x\n", __func__,
 		 pci_pcie_cap(ctrl->pcie->port) + PCI_EXP_SLTCTL, slot_cmd);
 
+	retval = pciehp_readw(ctrl, PCI_EXP_LNKSTA, &lnk_status);
+	if (retval) {
+		ctrl_err(ctrl, "%s: Cannot read LNKSTA register\n",
+				__func__);
+		return retval;
+	}
+	pcie_update_link_speed(ctrl->pcie->port->subordinate, lnk_status);
+
 	return retval;
 }
 
@@ -610,37 +619,6 @@
 	return IRQ_HANDLED;
 }
 
-int pciehp_get_max_link_speed(struct slot *slot, enum pci_bus_speed *value)
-{
-	struct controller *ctrl = slot->ctrl;
-	enum pcie_link_speed lnk_speed;
-	u32	lnk_cap;
-	int retval = 0;
-
-	retval = pciehp_readl(ctrl, PCI_EXP_LNKCAP, &lnk_cap);
-	if (retval) {
-		ctrl_err(ctrl, "%s: Cannot read LNKCAP register\n", __func__);
-		return retval;
-	}
-
-	switch (lnk_cap & 0x000F) {
-	case 1:
-		lnk_speed = PCIE_2_5GB;
-		break;
-	case 2:
-		lnk_speed = PCIE_5_0GB;
-		break;
-	default:
-		lnk_speed = PCIE_LNK_SPEED_UNKNOWN;
-		break;
-	}
-
-	*value = lnk_speed;
-	ctrl_dbg(ctrl, "Max link speed = %d\n", lnk_speed);
-
-	return retval;
-}
-
 int pciehp_get_max_lnk_width(struct slot *slot,
 				 enum pcie_link_width *value)
 {
@@ -691,38 +669,6 @@
 	return retval;
 }
 
-int pciehp_get_cur_link_speed(struct slot *slot, enum pci_bus_speed *value)
-{
-	struct controller *ctrl = slot->ctrl;
-	enum pcie_link_speed lnk_speed = PCI_SPEED_UNKNOWN;
-	int retval = 0;
-	u16 lnk_status;
-
-	retval = pciehp_readw(ctrl, PCI_EXP_LNKSTA, &lnk_status);
-	if (retval) {
-		ctrl_err(ctrl, "%s: Cannot read LNKSTATUS register\n",
-			 __func__);
-		return retval;
-	}
-
-	switch (lnk_status & PCI_EXP_LNKSTA_CLS) {
-	case 1:
-		lnk_speed = PCIE_2_5GB;
-		break;
-	case 2:
-		lnk_speed = PCIE_5_0GB;
-		break;
-	default:
-		lnk_speed = PCIE_LNK_SPEED_UNKNOWN;
-		break;
-	}
-
-	*value = lnk_speed;
-	ctrl_dbg(ctrl, "Current link speed = %d\n", lnk_speed);
-
-	return retval;
-}
-
 int pciehp_get_cur_lnk_width(struct slot *slot,
 				 enum pcie_link_width *value)
 {
diff --git a/drivers/pci/hotplug/pciehp_pci.c b/drivers/pci/hotplug/pciehp_pci.c
index 2173310..0a16444 100644
--- a/drivers/pci/hotplug/pciehp_pci.c
+++ b/drivers/pci/hotplug/pciehp_pci.c
@@ -53,17 +53,15 @@
 		busnr = pci_scan_bridge(parent, dev, busnr, pass);
 	if (!dev->subordinate)
 		return -1;
-	pci_bus_size_bridges(dev->subordinate);
-	pci_bus_assign_resources(parent);
-	pci_enable_bridges(parent);
-	pci_bus_add_devices(parent);
+
 	return 0;
 }
 
 int pciehp_configure_device(struct slot *p_slot)
 {
 	struct pci_dev *dev;
-	struct pci_bus *parent = p_slot->ctrl->pcie->port->subordinate;
+	struct pci_dev *bridge = p_slot->ctrl->pcie->port;
+	struct pci_bus *parent = bridge->subordinate;
 	int num, fn;
 	struct controller *ctrl = p_slot->ctrl;
 
@@ -96,12 +94,25 @@
 				(dev->hdr_type == PCI_HEADER_TYPE_CARDBUS)) {
 			pciehp_add_bridge(dev);
 		}
+		pci_dev_put(dev);
+	}
+
+	pci_assign_unassigned_bridge_resources(bridge);
+
+	for (fn = 0; fn < 8; fn++) {
+		dev = pci_get_slot(parent, PCI_DEVFN(0, fn));
+		if (!dev)
+			continue;
+		if ((dev->class >> 16) == PCI_BASE_CLASS_DISPLAY) {
+			pci_dev_put(dev);
+			continue;
+		}
 		pci_configure_slot(dev);
 		pci_dev_put(dev);
 	}
 
-	pci_bus_assign_resources(parent);
 	pci_bus_add_devices(parent);
+
 	return 0;
 }
 
diff --git a/drivers/pci/hotplug/rpaphp_core.c b/drivers/pci/hotplug/rpaphp_core.c
index c159223..dcaae72 100644
--- a/drivers/pci/hotplug/rpaphp_core.c
+++ b/drivers/pci/hotplug/rpaphp_core.c
@@ -130,10 +130,9 @@
 	return 0;
 }
 
-static int get_max_bus_speed(struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
+static enum pci_bus_speed get_max_bus_speed(struct slot *slot)
 {
-	struct slot *slot = (struct slot *)hotplug_slot->private;
-
+	enum pci_bus_speed speed;
 	switch (slot->type) {
 	case 1:
 	case 2:
@@ -141,30 +140,30 @@
 	case 4:
 	case 5:
 	case 6:
-		*value = PCI_SPEED_33MHz;	/* speed for case 1-6 */
+		speed = PCI_SPEED_33MHz;	/* speed for case 1-6 */
 		break;
 	case 7:
 	case 8:
-		*value = PCI_SPEED_66MHz;
+		speed = PCI_SPEED_66MHz;
 		break;
 	case 11:
 	case 14:
-		*value = PCI_SPEED_66MHz_PCIX;
+		speed = PCI_SPEED_66MHz_PCIX;
 		break;
 	case 12:
 	case 15:
-		*value = PCI_SPEED_100MHz_PCIX;
+		speed = PCI_SPEED_100MHz_PCIX;
 		break;
 	case 13:
 	case 16:
-		*value = PCI_SPEED_133MHz_PCIX;
+		speed = PCI_SPEED_133MHz_PCIX;
 		break;
 	default:
-		*value = PCI_SPEED_UNKNOWN;
+		speed = PCI_SPEED_UNKNOWN;
 		break;
-
 	}
-	return 0;
+
+	return speed;
 }
 
 static int get_children_props(struct device_node *dn, const int **drc_indexes,
@@ -408,6 +407,8 @@
 		slot->state = NOT_VALID;
 		return -EINVAL;
 	}
+
+	slot->bus->max_bus_speed = get_max_bus_speed(slot);
 	return 0;
 }
 
@@ -429,7 +430,6 @@
 	.get_power_status = get_power_status,
 	.get_attention_status = get_attention_status,
 	.get_adapter_status = get_adapter_status,
-	.get_max_bus_speed = get_max_bus_speed,
 };
 
 module_init(rpaphp_init);
diff --git a/drivers/pci/hotplug/shpchp.h b/drivers/pci/hotplug/shpchp.h
index 8e210cd7..d2627e1 100644
--- a/drivers/pci/hotplug/shpchp.h
+++ b/drivers/pci/hotplug/shpchp.h
@@ -333,8 +333,6 @@
 	int (*set_attention_status)(struct slot *slot, u8 status);
 	int (*get_latch_status)(struct slot *slot, u8 *status);
 	int (*get_adapter_status)(struct slot *slot, u8 *status);
-	int (*get_max_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
-	int (*get_cur_bus_speed)(struct slot *slot, enum pci_bus_speed *speed);
 	int (*get_adapter_speed)(struct slot *slot, enum pci_bus_speed *speed);
 	int (*get_mode1_ECC_cap)(struct slot *slot, u8 *mode);
 	int (*get_prog_int)(struct slot *slot, u8 *prog_int);
diff --git a/drivers/pci/hotplug/shpchp_core.c b/drivers/pci/hotplug/shpchp_core.c
index 8a520a3..a506229 100644
--- a/drivers/pci/hotplug/shpchp_core.c
+++ b/drivers/pci/hotplug/shpchp_core.c
@@ -65,8 +65,6 @@
 static int get_attention_status	(struct hotplug_slot *slot, u8 *value);
 static int get_latch_status	(struct hotplug_slot *slot, u8 *value);
 static int get_adapter_status	(struct hotplug_slot *slot, u8 *value);
-static int get_max_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
-static int get_cur_bus_speed	(struct hotplug_slot *slot, enum pci_bus_speed *value);
 
 static struct hotplug_slot_ops shpchp_hotplug_slot_ops = {
 	.set_attention_status =	set_attention_status,
@@ -76,8 +74,6 @@
 	.get_attention_status =	get_attention_status,
 	.get_latch_status =	get_latch_status,
 	.get_adapter_status =	get_adapter_status,
-	.get_max_bus_speed =	get_max_bus_speed,
-	.get_cur_bus_speed =	get_cur_bus_speed,
 };
 
 /**
@@ -279,37 +275,6 @@
 	return 0;
 }
 
-static int get_max_bus_speed(struct hotplug_slot *hotplug_slot,
-				enum pci_bus_speed *value)
-{
-	struct slot *slot = get_slot(hotplug_slot);
-	int retval;
-
-	ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
-		 __func__, slot_name(slot));
-
-	retval = slot->hpc_ops->get_max_bus_speed(slot, value);
-	if (retval < 0)
-		*value = PCI_SPEED_UNKNOWN;
-
-	return 0;
-}
-
-static int get_cur_bus_speed (struct hotplug_slot *hotplug_slot, enum pci_bus_speed *value)
-{
-	struct slot *slot = get_slot(hotplug_slot);
-	int retval;
-
-	ctrl_dbg(slot->ctrl, "%s: physical_slot = %s\n",
-		 __func__, slot_name(slot));
-
-	retval = slot->hpc_ops->get_cur_bus_speed(slot, value);
-	if (retval < 0)
-		*value = PCI_SPEED_UNKNOWN;
-
-	return 0;
-}
-
 static int is_shpc_capable(struct pci_dev *dev)
 {
 	if ((dev->vendor == PCI_VENDOR_ID_AMD) || (dev->device ==
diff --git a/drivers/pci/hotplug/shpchp_ctrl.c b/drivers/pci/hotplug/shpchp_ctrl.c
index b8ab279..3bba0c0 100644
--- a/drivers/pci/hotplug/shpchp_ctrl.c
+++ b/drivers/pci/hotplug/shpchp_ctrl.c
@@ -285,17 +285,8 @@
 		return WRONG_BUS_FREQUENCY;
 	}
 
-	rc = p_slot->hpc_ops->get_cur_bus_speed(p_slot, &bsp);
-	if (rc) {
-		ctrl_err(ctrl, "Can't get bus operation speed\n");
-		return WRONG_BUS_FREQUENCY;
-	}
-
-	rc = p_slot->hpc_ops->get_max_bus_speed(p_slot, &msp);
-	if (rc) {
-		ctrl_err(ctrl, "Can't get max bus operation speed\n");
-		msp = bsp;
-	}
+	bsp = ctrl->pci_dev->bus->cur_bus_speed;
+	msp = ctrl->pci_dev->bus->max_bus_speed;
 
 	/* Check if there are other slots or devices on the same bus */
 	if (!list_empty(&ctrl->pci_dev->subordinate->devices))
@@ -462,6 +453,7 @@
 		p_slot->state = POWERON_STATE;
 		break;
 	default:
+		kfree(info);
 		goto out;
 	}
 	queue_work(shpchp_wq, &info->work);
diff --git a/drivers/pci/hotplug/shpchp_hpc.c b/drivers/pci/hotplug/shpchp_hpc.c
index 86dc398..5f5e8d2 100644
--- a/drivers/pci/hotplug/shpchp_hpc.c
+++ b/drivers/pci/hotplug/shpchp_hpc.c
@@ -660,6 +660,75 @@
 	return retval;
 }
 
+static int shpc_get_cur_bus_speed(struct controller *ctrl)
+{
+	int retval = 0;
+	struct pci_bus *bus = ctrl->pci_dev->subordinate;
+	enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
+	u16 sec_bus_reg = shpc_readw(ctrl, SEC_BUS_CONFIG);
+	u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
+	u8 speed_mode = (pi == 2) ? (sec_bus_reg & 0xF) : (sec_bus_reg & 0x7);
+
+	if ((pi == 1) && (speed_mode > 4)) {
+		retval = -ENODEV;
+		goto out;
+	}
+
+	switch (speed_mode) {
+	case 0x0:
+		bus_speed = PCI_SPEED_33MHz;
+		break;
+	case 0x1:
+		bus_speed = PCI_SPEED_66MHz;
+		break;
+	case 0x2:
+		bus_speed = PCI_SPEED_66MHz_PCIX;
+		break;
+	case 0x3:
+		bus_speed = PCI_SPEED_100MHz_PCIX;
+		break;
+	case 0x4:
+		bus_speed = PCI_SPEED_133MHz_PCIX;
+		break;
+	case 0x5:
+		bus_speed = PCI_SPEED_66MHz_PCIX_ECC;
+		break;
+	case 0x6:
+		bus_speed = PCI_SPEED_100MHz_PCIX_ECC;
+		break;
+	case 0x7:
+		bus_speed = PCI_SPEED_133MHz_PCIX_ECC;
+		break;
+	case 0x8:
+		bus_speed = PCI_SPEED_66MHz_PCIX_266;
+		break;
+	case 0x9:
+		bus_speed = PCI_SPEED_100MHz_PCIX_266;
+		break;
+	case 0xa:
+		bus_speed = PCI_SPEED_133MHz_PCIX_266;
+		break;
+	case 0xb:
+		bus_speed = PCI_SPEED_66MHz_PCIX_533;
+		break;
+	case 0xc:
+		bus_speed = PCI_SPEED_100MHz_PCIX_533;
+		break;
+	case 0xd:
+		bus_speed = PCI_SPEED_133MHz_PCIX_533;
+		break;
+	default:
+		retval = -ENODEV;
+		break;
+	}
+
+ out:
+	bus->cur_bus_speed = bus_speed;
+	dbg("Current bus speed = %d\n", bus_speed);
+	return retval;
+}
+
+
 static int hpc_set_bus_speed_mode(struct slot * slot, enum pci_bus_speed value)
 {
 	int retval;
@@ -720,6 +789,8 @@
 	retval = shpc_write_cmd(slot, 0, cmd);
 	if (retval)
 		ctrl_err(ctrl, "%s: Write command failed!\n", __func__);
+	else
+		shpc_get_cur_bus_speed(ctrl);
 
 	return retval;
 }
@@ -803,10 +874,10 @@
 	return IRQ_HANDLED;
 }
 
-static int hpc_get_max_bus_speed (struct slot *slot, enum pci_bus_speed *value)
+static int shpc_get_max_bus_speed(struct controller *ctrl)
 {
 	int retval = 0;
-	struct controller *ctrl = slot->ctrl;
+	struct pci_bus *bus = ctrl->pci_dev->subordinate;
 	enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
 	u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
 	u32 slot_avail1 = shpc_readl(ctrl, SLOT_AVAIL1);
@@ -842,79 +913,12 @@
 			retval = -ENODEV;
 	}
 
-	*value = bus_speed;
+	bus->max_bus_speed = bus_speed;
 	ctrl_dbg(ctrl, "Max bus speed = %d\n", bus_speed);
 
 	return retval;
 }
 
-static int hpc_get_cur_bus_speed (struct slot *slot, enum pci_bus_speed *value)
-{
-	int retval = 0;
-	struct controller *ctrl = slot->ctrl;
-	enum pci_bus_speed bus_speed = PCI_SPEED_UNKNOWN;
-	u16 sec_bus_reg = shpc_readw(ctrl, SEC_BUS_CONFIG);
-	u8 pi = shpc_readb(ctrl, PROG_INTERFACE);
-	u8 speed_mode = (pi == 2) ? (sec_bus_reg & 0xF) : (sec_bus_reg & 0x7);
-
-	if ((pi == 1) && (speed_mode > 4)) {
-		*value = PCI_SPEED_UNKNOWN;
-		return -ENODEV;
-	}
-
-	switch (speed_mode) {
-	case 0x0:
-		*value = PCI_SPEED_33MHz;
-		break;
-	case 0x1:
-		*value = PCI_SPEED_66MHz;
-		break;
-	case 0x2:
-		*value = PCI_SPEED_66MHz_PCIX;
-		break;
-	case 0x3:
-		*value = PCI_SPEED_100MHz_PCIX;
-		break;
-	case 0x4:
-		*value = PCI_SPEED_133MHz_PCIX;
-		break;
-	case 0x5:
-		*value = PCI_SPEED_66MHz_PCIX_ECC;
-		break;
-	case 0x6:
-		*value = PCI_SPEED_100MHz_PCIX_ECC;
-		break;
-	case 0x7:
-		*value = PCI_SPEED_133MHz_PCIX_ECC;
-		break;
-	case 0x8:
-		*value = PCI_SPEED_66MHz_PCIX_266;
-		break;
-	case 0x9:
-		*value = PCI_SPEED_100MHz_PCIX_266;
-		break;
-	case 0xa:
-		*value = PCI_SPEED_133MHz_PCIX_266;
-		break;
-	case 0xb:
-		*value = PCI_SPEED_66MHz_PCIX_533;
-		break;
-	case 0xc:
-		*value = PCI_SPEED_100MHz_PCIX_533;
-		break;
-	case 0xd:
-		*value = PCI_SPEED_133MHz_PCIX_533;
-		break;
-	default:
-		*value = PCI_SPEED_UNKNOWN;
-		retval = -ENODEV;
-		break;
-	}
-
-	ctrl_dbg(ctrl, "Current bus speed = %d\n", bus_speed);
-	return retval;
-}
-
 static struct hpc_ops shpchp_hpc_ops = {
 	.power_on_slot			= hpc_power_on_slot,
 	.slot_enable			= hpc_slot_enable,
@@ -926,8 +930,6 @@
 	.get_latch_status		= hpc_get_latch_status,
 	.get_adapter_status		= hpc_get_adapter_status,
 
-	.get_max_bus_speed		= hpc_get_max_bus_speed,
-	.get_cur_bus_speed		= hpc_get_cur_bus_speed,
 	.get_adapter_speed		= hpc_get_adapter_speed,
 	.get_mode1_ECC_cap		= hpc_get_mode1_ECC_cap,
 	.get_prog_int			= hpc_get_prog_int,
@@ -1086,6 +1088,9 @@
 	}
 	ctrl_dbg(ctrl, "HPC at %s irq=%x\n", pci_name(pdev), pdev->irq);
 
+	shpc_get_max_bus_speed(ctrl);
+	shpc_get_cur_bus_speed(ctrl);
+
 	/*
 	 * If this is the first controller to be initialized,
 	 * initialize the shpchpd work queue
diff --git a/drivers/pci/hotplug/shpchp_sysfs.c b/drivers/pci/hotplug/shpchp_sysfs.c
index 29fa9d2..071b7dc 100644
--- a/drivers/pci/hotplug/shpchp_sysfs.c
+++ b/drivers/pci/hotplug/shpchp_sysfs.c
@@ -47,8 +47,7 @@
 	bus = pdev->subordinate;
 
 	out += sprintf(buf, "Free resources: memory\n");
-	for (index = 0; index < PCI_BUS_NUM_RESOURCES; index++) {
-		res = bus->resource[index];
+	pci_bus_for_each_resource(bus, res, index) {
 		if (res && (res->flags & IORESOURCE_MEM) &&
 				!(res->flags & IORESOURCE_PREFETCH)) {
 			out += sprintf(out, "start = %8.8llx, "
@@ -58,8 +57,7 @@
 		}
 	}
 	out += sprintf(out, "Free resources: prefetchable memory\n");
-	for (index = 0; index < PCI_BUS_NUM_RESOURCES; index++) {
-		res = bus->resource[index];
+	pci_bus_for_each_resource(bus, res, index) {
 		if (res && (res->flags & IORESOURCE_MEM) &&
 			       (res->flags & IORESOURCE_PREFETCH)) {
 			out += sprintf(out, "start = %8.8llx, "
@@ -69,8 +67,7 @@
 		}
 	}
 	out += sprintf(out, "Free resources: IO\n");
-	for (index = 0; index < PCI_BUS_NUM_RESOURCES; index++) {
-		res = bus->resource[index];
+	pci_bus_for_each_resource(bus, res, index) {
 		if (res && (res->flags & IORESOURCE_IO)) {
 			out += sprintf(out, "start = %8.8llx, "
 					"length = %8.8llx\n",
diff --git a/drivers/pci/legacy.c b/drivers/pci/legacy.c
deleted file mode 100644
index 871f65c..0000000
--- a/drivers/pci/legacy.c
+++ /dev/null
@@ -1,34 +0,0 @@
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include "pci.h"
-
-/**
- * pci_find_device - begin or continue searching for a PCI device by vendor/device id
- * @vendor: PCI vendor id to match, or %PCI_ANY_ID to match all vendor ids
- * @device: PCI device id to match, or %PCI_ANY_ID to match all device ids
- * @from: Previous PCI device found in search, or %NULL for new search.
- *
- * Iterates through the list of known PCI devices.  If a PCI device is found
- * with a matching @vendor and @device, a pointer to its device structure is
- * returned.  Otherwise, %NULL is returned.
- * A new search is initiated by passing %NULL as the @from argument.
- * Otherwise if @from is not %NULL, searches continue from next device
- * on the global list.
- *
- * NOTE: Do not use this function any more; use pci_get_device() instead, as
- * the PCI device returned by this function can disappear at any moment in
- * time.
- */
-struct pci_dev *pci_find_device(unsigned int vendor, unsigned int device,
-				struct pci_dev *from)
-{
-	struct pci_dev *pdev;
-
-	pci_dev_get(from);
-	pdev = pci_get_subsys(vendor, device, PCI_ANY_ID, PCI_ANY_ID, from);
-	pci_dev_put(pdev);
-	return pdev;
-}
-EXPORT_SYMBOL(pci_find_device);
diff --git a/drivers/pci/pci-acpi.c b/drivers/pci/pci-acpi.c
index 7e28295..c0c7391 100644
--- a/drivers/pci/pci-acpi.c
+++ b/drivers/pci/pci-acpi.c
@@ -16,8 +16,144 @@
 #include <acpi/acpi_bus.h>
 
 #include <linux/pci-acpi.h>
+#include <linux/pm_runtime.h>
 #include "pci.h"
 
+static DEFINE_MUTEX(pci_acpi_pm_notify_mtx);
+
+/**
+ * pci_acpi_wake_bus - Wake-up notification handler for root buses.
+ * @handle: ACPI handle of a device the notification is for.
+ * @event: Type of the signaled event.
+ * @context: PCI root bus to wake up devices on.
+ */
+static void pci_acpi_wake_bus(acpi_handle handle, u32 event, void *context)
+{
+	struct pci_bus *pci_bus = context;
+
+	if (event == ACPI_NOTIFY_DEVICE_WAKE && pci_bus)
+		pci_pme_wakeup_bus(pci_bus);
+}
+
+/**
+ * pci_acpi_wake_dev - Wake-up notification handler for PCI devices.
+ * @handle: ACPI handle of a device the notification is for.
+ * @event: Type of the signaled event.
+ * @context: PCI device object to wake up.
+ */
+static void pci_acpi_wake_dev(acpi_handle handle, u32 event, void *context)
+{
+	struct pci_dev *pci_dev = context;
+
+	if (event == ACPI_NOTIFY_DEVICE_WAKE && pci_dev) {
+		pci_check_pme_status(pci_dev);
+		pm_runtime_resume(&pci_dev->dev);
+		if (pci_dev->subordinate)
+			pci_pme_wakeup_bus(pci_dev->subordinate);
+	}
+}
+
+/**
+ * add_pm_notifier - Register PM notifier for given ACPI device.
+ * @dev: ACPI device to add the notifier for.
+ * @context: PCI device or bus to check for PME status if an event is signaled.
+ *
+ * NOTE: @dev need not be a run-wake or wake-up device to be a valid source of
+ * PM wake-up events.  For example, wake-up events may be generated for bridges
+ * if one of the devices below the bridge is signaling PME, even if the bridge
+ * itself doesn't have a wake-up GPE associated with it.
+ */
+static acpi_status add_pm_notifier(struct acpi_device *dev,
+				   acpi_notify_handler handler,
+				   void *context)
+{
+	acpi_status status = AE_ALREADY_EXISTS;
+
+	mutex_lock(&pci_acpi_pm_notify_mtx);
+
+	if (dev->wakeup.flags.notifier_present)
+		goto out;
+
+	status = acpi_install_notify_handler(dev->handle,
+					     ACPI_SYSTEM_NOTIFY,
+					     handler, context);
+	if (ACPI_FAILURE(status))
+		goto out;
+
+	dev->wakeup.flags.notifier_present = true;
+
+ out:
+	mutex_unlock(&pci_acpi_pm_notify_mtx);
+	return status;
+}
+
+/**
+ * remove_pm_notifier - Unregister PM notifier from given ACPI device.
+ * @dev: ACPI device to remove the notifier from.
+ */
+static acpi_status remove_pm_notifier(struct acpi_device *dev,
+				      acpi_notify_handler handler)
+{
+	acpi_status status = AE_BAD_PARAMETER;
+
+	mutex_lock(&pci_acpi_pm_notify_mtx);
+
+	if (!dev->wakeup.flags.notifier_present)
+		goto out;
+
+	status = acpi_remove_notify_handler(dev->handle,
+					    ACPI_SYSTEM_NOTIFY,
+					    handler);
+	if (ACPI_FAILURE(status))
+		goto out;
+
+	dev->wakeup.flags.notifier_present = false;
+
+ out:
+	mutex_unlock(&pci_acpi_pm_notify_mtx);
+	return status;
+}
+
+/**
+ * pci_acpi_add_bus_pm_notifier - Register PM notifier for given PCI bus.
+ * @dev: ACPI device to add the notifier for.
+ * @pci_bus: PCI bus to walk checking for PME status if an event is signaled.
+ */
+acpi_status pci_acpi_add_bus_pm_notifier(struct acpi_device *dev,
+					 struct pci_bus *pci_bus)
+{
+	return add_pm_notifier(dev, pci_acpi_wake_bus, pci_bus);
+}
+
+/**
+ * pci_acpi_remove_bus_pm_notifier - Unregister PCI bus PM notifier.
+ * @dev: ACPI device to remove the notifier from.
+ */
+acpi_status pci_acpi_remove_bus_pm_notifier(struct acpi_device *dev)
+{
+	return remove_pm_notifier(dev, pci_acpi_wake_bus);
+}
+
+/**
+ * pci_acpi_add_pm_notifier - Register PM notifier for given PCI device.
+ * @dev: ACPI device to add the notifier for.
+ * @pci_dev: PCI device to check for the PME status if an event is signaled.
+ */
+acpi_status pci_acpi_add_pm_notifier(struct acpi_device *dev,
+				     struct pci_dev *pci_dev)
+{
+	return add_pm_notifier(dev, pci_acpi_wake_dev, pci_dev);
+}
+
+/**
+ * pci_acpi_remove_pm_notifier - Unregister PCI device PM notifier.
+ * @dev: ACPI device to remove the notifier from.
+ */
+acpi_status pci_acpi_remove_pm_notifier(struct acpi_device *dev)
+{
+	return remove_pm_notifier(dev, pci_acpi_wake_dev);
+}
+
 /*
  * _SxD returns the D-state with the highest power
  * (lowest D-state number) supported in the S-state "x".
@@ -131,12 +267,87 @@
 	return 0;
 }
 
+/**
+ * acpi_dev_run_wake - Enable/disable wake-up for given device.
+ * @phys_dev: Device to enable/disable the platform to wake-up the system for.
+ * @enable: Whether enable or disable the wake-up functionality.
+ *
+ * Find the ACPI device object corresponding to @pci_dev and try to
+ * enable/disable the GPE associated with it.
+ */
+static int acpi_dev_run_wake(struct device *phys_dev, bool enable)
+{
+	struct acpi_device *dev;
+	acpi_handle handle;
+	int error = -ENODEV;
+
+	if (!device_run_wake(phys_dev))
+		return -EINVAL;
+
+	handle = DEVICE_ACPI_HANDLE(phys_dev);
+	if (!handle || ACPI_FAILURE(acpi_bus_get_device(handle, &dev))) {
+		dev_dbg(phys_dev, "ACPI handle has no context in %s!\n",
+			__func__);
+		return -ENODEV;
+	}
+
+	if (enable) {
+		if (!dev->wakeup.run_wake_count++) {
+			acpi_enable_wakeup_device_power(dev, ACPI_STATE_S0);
+			acpi_enable_gpe(dev->wakeup.gpe_device,
+					dev->wakeup.gpe_number,
+					ACPI_GPE_TYPE_RUNTIME);
+		}
+	} else if (dev->wakeup.run_wake_count > 0) {
+		if (!--dev->wakeup.run_wake_count) {
+			acpi_disable_gpe(dev->wakeup.gpe_device,
+					 dev->wakeup.gpe_number,
+					 ACPI_GPE_TYPE_RUNTIME);
+			acpi_disable_wakeup_device_power(dev);
+		}
+	} else {
+		error = -EALREADY;
+	}
+
+	return error;
+}
+
+static void acpi_pci_propagate_run_wake(struct pci_bus *bus, bool enable)
+{
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+
+		if (bridge->pme_interrupt)
+			return;
+		if (!acpi_dev_run_wake(&bridge->dev, enable))
+			return;
+		bus = bus->parent;
+	}
+
+	/* We have reached the root bus. */
+	if (bus->bridge)
+		acpi_dev_run_wake(bus->bridge, enable);
+}
+
+static int acpi_pci_run_wake(struct pci_dev *dev, bool enable)
+{
+	if (dev->pme_interrupt)
+		return 0;
+
+	if (!acpi_dev_run_wake(&dev->dev, enable))
+		return 0;
+
+	acpi_pci_propagate_run_wake(dev->bus, enable);
+	return 0;
+}
+
 static struct pci_platform_pm_ops acpi_pci_platform_pm = {
 	.is_manageable = acpi_pci_power_manageable,
 	.set_state = acpi_pci_set_power_state,
 	.choose_state = acpi_pci_choose_state,
 	.can_wakeup = acpi_pci_can_wakeup,
 	.sleep_wake = acpi_pci_sleep_wake,
+	.run_wake = acpi_pci_run_wake,
 };
 
 /* ACPI bus type */
diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index e5d47be..f9a0aec 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -17,6 +17,7 @@
 #include <linux/slab.h>
 #include <linux/sched.h>
 #include <linux/cpu.h>
+#include <linux/pm_runtime.h>
 #include "pci.h"
 
 struct pci_dynid {
@@ -404,6 +405,35 @@
 	pci_msix_shutdown(pci_dev);
 }
 
+#ifdef CONFIG_PM_OPS
+
+/* Auxiliary functions used for system resume and run-time resume. */
+
+/**
+ * pci_restore_standard_config - restore standard config registers of PCI device
+ * @pci_dev: PCI device to handle
+ */
+static int pci_restore_standard_config(struct pci_dev *pci_dev)
+{
+	pci_update_current_state(pci_dev, PCI_UNKNOWN);
+
+	if (pci_dev->current_state != PCI_D0) {
+		int error = pci_set_power_state(pci_dev, PCI_D0);
+		if (error)
+			return error;
+	}
+
+	return pci_restore_state(pci_dev);
+}
+
+static void pci_pm_default_resume_early(struct pci_dev *pci_dev)
+{
+	pci_restore_standard_config(pci_dev);
+	pci_fixup_device(pci_fixup_resume_early, pci_dev);
+}
+
+#endif
+
 #ifdef CONFIG_PM_SLEEP
 
 /*
@@ -520,29 +550,6 @@
 
 /* Auxiliary functions used by the new power management framework */
 
-/**
- * pci_restore_standard_config - restore standard config registers of PCI device
- * @pci_dev: PCI device to handle
- */
-static int pci_restore_standard_config(struct pci_dev *pci_dev)
-{
-	pci_update_current_state(pci_dev, PCI_UNKNOWN);
-
-	if (pci_dev->current_state != PCI_D0) {
-		int error = pci_set_power_state(pci_dev, PCI_D0);
-		if (error)
-			return error;
-	}
-
-	return pci_restore_state(pci_dev);
-}
-
-static void pci_pm_default_resume_noirq(struct pci_dev *pci_dev)
-{
-	pci_restore_standard_config(pci_dev);
-	pci_fixup_device(pci_fixup_resume_early, pci_dev);
-}
-
 static void pci_pm_default_resume(struct pci_dev *pci_dev)
 {
 	pci_fixup_device(pci_fixup_resume, pci_dev);
@@ -581,6 +588,17 @@
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
+	/*
+	 * PCI devices suspended at run time need to be resumed at this
+	 * point, because in general it is necessary to reconfigure them for
+	 * system suspend.  Namely, if the device is supposed to wake up the
+	 * system from the sleep state, we may need to reconfigure it for this
+	 * purpose.  In turn, if the device is not supposed to wake up the
+	 * system from the sleep state, we'll have to prevent it from signaling
+	 * wake-up.
+	 */
+	pm_runtime_resume(dev);
+
 	if (drv && drv->pm && drv->pm->prepare)
 		error = drv->pm->prepare(dev);
 
@@ -595,6 +613,13 @@
 		drv->pm->complete(dev);
 }
 
+#else /* !CONFIG_PM_SLEEP */
+
+#define pci_pm_prepare	NULL
+#define pci_pm_complete	NULL
+
+#endif /* !CONFIG_PM_SLEEP */
+
 #ifdef CONFIG_SUSPEND
 
 static int pci_pm_suspend(struct device *dev)
@@ -681,7 +706,7 @@
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
-	pci_pm_default_resume_noirq(pci_dev);
+	pci_pm_default_resume_early(pci_dev);
 
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_resume_early(dev);
@@ -879,7 +904,7 @@
 	struct device_driver *drv = dev->driver;
 	int error = 0;
 
-	pci_pm_default_resume_noirq(pci_dev);
+	pci_pm_default_resume_early(pci_dev);
 
 	if (pci_has_legacy_pm_support(pci_dev))
 		return pci_legacy_resume_early(dev);
@@ -931,6 +956,84 @@
 
 #endif /* !CONFIG_HIBERNATION */
 
+#ifdef CONFIG_PM_RUNTIME
+
+static int pci_pm_runtime_suspend(struct device *dev)
+{
+	struct pci_dev *pci_dev = to_pci_dev(dev);
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+	pci_power_t prev = pci_dev->current_state;
+	int error;
+
+	if (!pm || !pm->runtime_suspend)
+		return -ENOSYS;
+
+	error = pm->runtime_suspend(dev);
+	suspend_report_result(pm->runtime_suspend, error);
+	if (error)
+		return error;
+
+	pci_fixup_device(pci_fixup_suspend, pci_dev);
+
+	if (!pci_dev->state_saved && pci_dev->current_state != PCI_D0
+	    && pci_dev->current_state != PCI_UNKNOWN) {
+		WARN_ONCE(pci_dev->current_state != prev,
+			"PCI PM: State of device not saved by %pF\n",
+			pm->runtime_suspend);
+		return 0;
+	}
+
+	if (!pci_dev->state_saved)
+		pci_save_state(pci_dev);
+
+	pci_finish_runtime_suspend(pci_dev);
+
+	return 0;
+}
+
+static int pci_pm_runtime_resume(struct device *dev)
+{
+	struct pci_dev *pci_dev = to_pci_dev(dev);
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm || !pm->runtime_resume)
+		return -ENOSYS;
+
+	pci_pm_default_resume_early(pci_dev);
+	__pci_enable_wake(pci_dev, PCI_D0, true, false);
+	pci_fixup_device(pci_fixup_resume, pci_dev);
+
+	return pm->runtime_resume(dev);
+}
+
+static int pci_pm_runtime_idle(struct device *dev)
+{
+	const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
+
+	if (!pm)
+		return -ENOSYS;
+
+	if (pm->runtime_idle) {
+		int ret = pm->runtime_idle(dev);
+		if (ret)
+			return ret;
+	}
+
+	pm_runtime_suspend(dev);
+
+	return 0;
+}
+
+#else /* !CONFIG_PM_RUNTIME */
+
+#define pci_pm_runtime_suspend	NULL
+#define pci_pm_runtime_resume	NULL
+#define pci_pm_runtime_idle	NULL
+
+#endif /* !CONFIG_PM_RUNTIME */
+
+#ifdef CONFIG_PM_OPS
+
 const struct dev_pm_ops pci_dev_pm_ops = {
 	.prepare = pci_pm_prepare,
 	.complete = pci_pm_complete,
@@ -946,15 +1049,18 @@
 	.thaw_noirq = pci_pm_thaw_noirq,
 	.poweroff_noirq = pci_pm_poweroff_noirq,
 	.restore_noirq = pci_pm_restore_noirq,
+	.runtime_suspend = pci_pm_runtime_suspend,
+	.runtime_resume = pci_pm_runtime_resume,
+	.runtime_idle = pci_pm_runtime_idle,
 };
 
 #define PCI_PM_OPS_PTR	(&pci_dev_pm_ops)
 
-#else /* !CONFIG_PM_SLEEP */
+#else /* !COMFIG_PM_OPS */
 
 #define PCI_PM_OPS_PTR	NULL
 
-#endif /* !CONFIG_PM_SLEEP */
+#endif /* !COMFIG_PM_OPS */
 
 /**
  * __pci_register_driver - register a new pci driver
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 315fea4..f4a2738 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -19,8 +19,8 @@
 #include <linux/pci-aspm.h>
 #include <linux/pm_wakeup.h>
 #include <linux/interrupt.h>
-#include <asm/dma.h>	/* isa_dma_bridge_buggy */
 #include <linux/device.h>
+#include <linux/pm_runtime.h>
 #include <asm/setup.h>
 #include "pci.h"
 
@@ -29,6 +29,12 @@
 };
 EXPORT_SYMBOL_GPL(pci_power_names);
 
+int isa_dma_bridge_buggy;
+EXPORT_SYMBOL(isa_dma_bridge_buggy);
+
+int pci_pci_problems;
+EXPORT_SYMBOL(pci_pci_problems);
+
 unsigned int pci_pm_d3_delay;
 
 static void pci_dev_d3_sleep(struct pci_dev *dev)
@@ -380,10 +386,9 @@
 {
 	const struct pci_bus *bus = dev->bus;
 	int i;
-	struct resource *best = NULL;
+	struct resource *best = NULL, *r;
 
-	for(i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		struct resource *r = bus->resource[i];
+	pci_bus_for_each_resource(bus, r, i) {
 		if (!r)
 			continue;
 		if (res->start && !(res->start >= r->start && res->end <= r->end))
@@ -457,6 +462,12 @@
 			pci_platform_pm->sleep_wake(dev, enable) : -ENODEV;
 }
 
+static inline int platform_pci_run_wake(struct pci_dev *dev, bool enable)
+{
+	return pci_platform_pm ?
+			pci_platform_pm->run_wake(dev, enable) : -ENODEV;
+}
+
 /**
  * pci_raw_set_power_state - Use PCI PM registers to set the power state of
  *                           given PCI device
@@ -1190,6 +1201,66 @@
 }
 
 /**
+ * pci_check_pme_status - Check if given device has generated PME.
+ * @dev: Device to check.
+ *
+ * Check the PME status of the device and if set, clear it and clear PME enable
+ * (if set).  Return 'true' if PME status and PME enable were both set or
+ * 'false' otherwise.
+ */
+bool pci_check_pme_status(struct pci_dev *dev)
+{
+	int pmcsr_pos;
+	u16 pmcsr;
+	bool ret = false;
+
+	if (!dev->pm_cap)
+		return false;
+
+	pmcsr_pos = dev->pm_cap + PCI_PM_CTRL;
+	pci_read_config_word(dev, pmcsr_pos, &pmcsr);
+	if (!(pmcsr & PCI_PM_CTRL_PME_STATUS))
+		return false;
+
+	/* Clear PME status. */
+	pmcsr |= PCI_PM_CTRL_PME_STATUS;
+	if (pmcsr & PCI_PM_CTRL_PME_ENABLE) {
+		/* Disable PME to avoid interrupt flood. */
+		pmcsr &= ~PCI_PM_CTRL_PME_ENABLE;
+		ret = true;
+	}
+
+	pci_write_config_word(dev, pmcsr_pos, pmcsr);
+
+	return ret;
+}
+
+/**
+ * pci_pme_wakeup - Wake up a PCI device if its PME Status bit is set.
+ * @dev: Device to handle.
+ * @ign: Ignored.
+ *
+ * Check if @dev has generated PME and queue a resume request for it in that
+ * case.
+ */
+static int pci_pme_wakeup(struct pci_dev *dev, void *ign)
+{
+	if (pci_check_pme_status(dev))
+		pm_request_resume(&dev->dev);
+	return 0;
+}
+
+/**
+ * pci_pme_wakeup_bus - Walk given bus and wake up devices on it, if necessary.
+ * @bus: Top bus of the subtree to walk.
+ */
+void pci_pme_wakeup_bus(struct pci_bus *bus)
+{
+	if (bus)
+		pci_walk_bus(bus, pci_pme_wakeup, NULL);
+}
+
+/**
  * pci_pme_capable - check the capability of PCI device to generate PME#
  * @dev: PCI device to handle.
  * @state: PCI state from which device will issue PME#.
@@ -1230,9 +1301,10 @@
 }
 
 /**
- * pci_enable_wake - enable PCI device as wakeup event source
+ * __pci_enable_wake - enable PCI device as wakeup event source
  * @dev: PCI device affected
  * @state: PCI state from which device will issue wakeup events
+ * @runtime: True if the events are to be generated at run time
  * @enable: True to enable event generation; false to disable
  *
  * This enables the device as a wakeup event source, or disables it.
@@ -1248,11 +1320,12 @@
  * Error code depending on the platform is returned if both the platform and
  * the native mechanism fail to enable the generation of wake-up events
  */
-int pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enable)
+int __pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+		      bool runtime, bool enable)
 {
 	int ret = 0;
 
-	if (enable && !device_may_wakeup(&dev->dev))
+	if (enable && !runtime && !device_may_wakeup(&dev->dev))
 		return -EINVAL;
 
 	/* Don't do the same thing twice in a row for one device. */
@@ -1272,19 +1345,24 @@
 			pci_pme_active(dev, true);
 		else
 			ret = 1;
-		error = platform_pci_sleep_wake(dev, true);
+		error = runtime ? platform_pci_run_wake(dev, true) :
+					platform_pci_sleep_wake(dev, true);
 		if (ret)
 			ret = error;
 		if (!ret)
 			dev->wakeup_prepared = true;
 	} else {
-		platform_pci_sleep_wake(dev, false);
+		if (runtime)
+			platform_pci_run_wake(dev, false);
+		else
+			platform_pci_sleep_wake(dev, false);
 		pci_pme_active(dev, false);
 		dev->wakeup_prepared = false;
 	}
 
 	return ret;
 }
+EXPORT_SYMBOL(__pci_enable_wake);
 
 /**
  * pci_wake_from_d3 - enable/disable device to wake up from D3_hot or D3_cold
@@ -1394,6 +1472,66 @@
 }
 
 /**
+ * pci_finish_runtime_suspend - Carry out PCI-specific part of runtime suspend.
+ * @dev: PCI device being suspended.
+ *
+ * Prepare @dev to generate wake-up events at run time and put it into a low
+ * power state.
+ */
+int pci_finish_runtime_suspend(struct pci_dev *dev)
+{
+	pci_power_t target_state = pci_target_state(dev);
+	int error;
+
+	if (target_state == PCI_POWER_ERROR)
+		return -EIO;
+
+	__pci_enable_wake(dev, target_state, true, pci_dev_run_wake(dev));
+
+	error = pci_set_power_state(dev, target_state);
+
+	if (error)
+		__pci_enable_wake(dev, target_state, true, false);
+
+	return error;
+}
+
+/**
+ * pci_dev_run_wake - Check if device can generate run-time wake-up events.
+ * @dev: Device to check.
+ *
+ * Return true if the device itself is cabable of generating wake-up events
+ * (through the platform or using the native PCIe PME) or if the device supports
+ * PME and one of its upstream bridges can generate wake-up events.
+ */
+bool pci_dev_run_wake(struct pci_dev *dev)
+{
+	struct pci_bus *bus = dev->bus;
+
+	if (device_run_wake(&dev->dev))
+		return true;
+
+	if (!dev->pme_support)
+		return false;
+
+	while (bus->parent) {
+		struct pci_dev *bridge = bus->self;
+
+		if (device_run_wake(&bridge->dev))
+			return true;
+
+		bus = bus->parent;
+	}
+
+	/* We have reached the root bus. */
+	if (bus->bridge)
+		return device_run_wake(bus->bridge);
+
+	return false;
+}
+EXPORT_SYMBOL_GPL(pci_dev_run_wake);
+
+/**
  * pci_pm_init - Initialize PM functions of given PCI device
  * @dev: PCI device to handle.
  */
@@ -2871,7 +3009,6 @@
 EXPORT_SYMBOL(pci_restore_state);
 EXPORT_SYMBOL(pci_pme_capable);
 EXPORT_SYMBOL(pci_pme_active);
-EXPORT_SYMBOL(pci_enable_wake);
 EXPORT_SYMBOL(pci_wake_from_d3);
 EXPORT_SYMBOL(pci_target_state);
 EXPORT_SYMBOL(pci_prepare_to_sleep);
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index fbd0e3a..4eb10f4 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -35,6 +35,10 @@
  *
  * @sleep_wake: enables/disables the system wake up capability of given device
  *
+ * @run_wake: enables/disables the platform to generate run-time wake-up events
+ *		for given device (the device's wake-up capability has to be
+ *		enabled by @sleep_wake for this feature to work)
+ *
  * If given platform is generally capable of power managing PCI devices, all of
  * these callbacks are mandatory.
  */
@@ -44,11 +48,16 @@
 	pci_power_t (*choose_state)(struct pci_dev *dev);
 	bool (*can_wakeup)(struct pci_dev *dev);
 	int (*sleep_wake)(struct pci_dev *dev, bool enable);
+	int (*run_wake)(struct pci_dev *dev, bool enable);
 };
 
 extern int pci_set_platform_pm(struct pci_platform_pm_ops *ops);
 extern void pci_update_current_state(struct pci_dev *dev, pci_power_t state);
 extern void pci_disable_enabled_device(struct pci_dev *dev);
+extern bool pci_check_pme_status(struct pci_dev *dev);
+extern int pci_finish_runtime_suspend(struct pci_dev *dev);
+extern int __pci_pme_wakeup(struct pci_dev *dev, void *ign);
+extern void pci_pme_wakeup_bus(struct pci_bus *bus);
 extern void pci_pm_init(struct pci_dev *dev);
 extern void platform_pci_wakeup_init(struct pci_dev *dev);
 extern void pci_allocate_cap_save_buffers(struct pci_dev *dev);
@@ -319,6 +328,13 @@
 	int (*reset)(struct pci_dev *dev, int probe);
 };
 
+#ifdef CONFIG_PCI_QUIRKS
 extern int pci_dev_specific_reset(struct pci_dev *dev, int probe);
+#else
+static inline int pci_dev_specific_reset(struct pci_dev *dev, int probe)
+{
+	return -ENOTTY;
+}
+#endif
 
 #endif /* DRIVERS_PCI_H */
diff --git a/drivers/pci/pcie/Kconfig b/drivers/pci/pcie/Kconfig
index 5a0c6ad..b8b494b 100644
--- a/drivers/pci/pcie/Kconfig
+++ b/drivers/pci/pcie/Kconfig
@@ -46,3 +46,7 @@
 	help
 	  This enables PCI Express ASPM debug support. It will add per-device
 	  interface to control ASPM.
+
+config PCIE_PME
+	def_bool y
+	depends on PCIEPORTBUS && PM_RUNTIME && EXPERIMENTAL && ACPI
diff --git a/drivers/pci/pcie/Makefile b/drivers/pci/pcie/Makefile
index 11f6bb1e..ea65454 100644
--- a/drivers/pci/pcie/Makefile
+++ b/drivers/pci/pcie/Makefile
@@ -11,3 +11,5 @@
 
 # Build PCI Express AER if needed
 obj-$(CONFIG_PCIEAER)		+= aer/
+
+obj-$(CONFIG_PCIE_PME) += pme/
diff --git a/drivers/pci/pcie/pme/Makefile b/drivers/pci/pcie/pme/Makefile
new file mode 100644
index 0000000..8b92380
--- /dev/null
+++ b/drivers/pci/pcie/pme/Makefile
@@ -0,0 +1,8 @@
+#
+# Makefile for PCI-Express Root Port PME signaling driver
+#
+
+obj-$(CONFIG_PCIE_PME) += pmedriver.o
+
+pmedriver-objs := pcie_pme.o
+pmedriver-$(CONFIG_ACPI) += pcie_pme_acpi.o
diff --git a/drivers/pci/pcie/pme/pcie_pme.c b/drivers/pci/pcie/pme/pcie_pme.c
new file mode 100644
index 0000000..7b3cbff
--- /dev/null
+++ b/drivers/pci/pcie/pme/pcie_pme.c
@@ -0,0 +1,505 @@
+/*
+ * PCIe Native PME support
+ *
+ * Copyright (C) 2007 - 2009 Intel Corp
+ * Copyright (C) 2007 - 2009 Shaohua Li <shaohua.li@intel.com>
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License V2.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <linux/pcieport_if.h>
+#include <linux/acpi.h>
+#include <linux/pci-acpi.h>
+#include <linux/pm_runtime.h>
+
+#include "../../pci.h"
+#include "pcie_pme.h"
+
+#define PCI_EXP_RTSTA_PME	0x10000 /* PME status */
+#define PCI_EXP_RTSTA_PENDING	0x20000 /* PME pending */
+
+/*
+ * If set, this switch will prevent the PCIe root port PME service driver from
+ * being registered.  Consequently, the interrupt-based PCIe PME signaling will
+ * not be used by any PCIe root ports in that case.
+ */
+static bool pcie_pme_disabled;
+
+/*
+ * The PCI Express Base Specification 2.0, Section 6.1.8, states the following:
+ * "In order to maintain compatibility with non-PCI Express-aware system
+ * software, system power management logic must be configured by firmware to use
+ * the legacy mechanism of signaling PME by default.  PCI Express-aware system
+ * software must notify the firmware prior to enabling native, interrupt-based
+ * PME signaling."  However, if the platform doesn't provide us with a suitable
+ * notification mechanism or the notification fails, it is not clear whether or
+ * not we are supposed to use the interrupt-based PCIe PME signaling.  The
+ * switch below can be used to indicate the desired behaviour.  When set, it
+ * will make the kernel use the interrupt-based PCIe PME signaling regardless of
+ * the platform notification status, although the kernel will attempt to notify
+ * the platform anyway.  When unset, it will prevent the kernel from using the
+ * the interrupt-based PCIe PME signaling if the platform notification fails,
+ * which is the default.
+ */
+static bool pcie_pme_force_enable;
+
+/*
+ * If this switch is set, MSI will not be used for PCIe PME signaling.  This
+ * causes the PCIe port driver to use INTx interrupts only, but it turns out
+ * that using MSI for PCIe PME signaling doesn't play well with PCIe PME-based
+ * wake-up from system sleep states.
+ */
+bool pcie_pme_msi_disabled;
+
+static int __init pcie_pme_setup(char *str)
+{
+	if (!strcmp(str, "off"))
+		pcie_pme_disabled = true;
+	else if (!strcmp(str, "force"))
+		pcie_pme_force_enable = true;
+	else if (!strcmp(str, "nomsi"))
+		pcie_pme_msi_disabled = true;
+	return 1;
+}
+__setup("pcie_pme=", pcie_pme_setup);
+
+/**
+ * pcie_pme_platform_setup - Ensure that the kernel controls the PCIe PME.
+ * @srv: PCIe PME root port service to use for carrying out the check.
+ *
+ * Notify the platform that the native PCIe PME is going to be used and return
+ * 'true' if the control of the PCIe PME registers has been acquired from the
+ * platform.
+ */
+static bool pcie_pme_platform_setup(struct pcie_device *srv)
+{
+	if (!pcie_pme_platform_notify(srv))
+		return true;
+	return pcie_pme_force_enable;
+}
+
+struct pcie_pme_service_data {
+	spinlock_t lock;
+	struct pcie_device *srv;
+	struct work_struct work;
+	bool noirq; /* Don't enable the PME interrupt used by this service. */
+};
+
+/**
+ * pcie_pme_interrupt_enable - Enable/disable PCIe PME interrupt generation.
+ * @dev: PCIe root port or event collector.
+ * @enable: Enable or disable the interrupt.
+ */
+static void pcie_pme_interrupt_enable(struct pci_dev *dev, bool enable)
+{
+	int rtctl_pos;
+	u16 rtctl;
+
+	rtctl_pos = pci_pcie_cap(dev) + PCI_EXP_RTCTL;
+
+	pci_read_config_word(dev, rtctl_pos, &rtctl);
+	if (enable)
+		rtctl |= PCI_EXP_RTCTL_PMEIE;
+	else
+		rtctl &= ~PCI_EXP_RTCTL_PMEIE;
+	pci_write_config_word(dev, rtctl_pos, rtctl);
+}
+
+/**
+ * pcie_pme_clear_status - Clear root port PME interrupt status.
+ * @dev: PCIe root port or event collector.
+ */
+static void pcie_pme_clear_status(struct pci_dev *dev)
+{
+	int rtsta_pos;
+	u32 rtsta;
+
+	rtsta_pos = pci_pcie_cap(dev) + PCI_EXP_RTSTA;
+
+	pci_read_config_dword(dev, rtsta_pos, &rtsta);
+	rtsta |= PCI_EXP_RTSTA_PME;
+	pci_write_config_dword(dev, rtsta_pos, rtsta);
+}
+
+/**
+ * pcie_pme_walk_bus - Scan a PCI bus for devices asserting PME#.
+ * @bus: PCI bus to scan.
+ *
+ * Scan given PCI bus and all buses under it for devices asserting PME#.
+ */
+static bool pcie_pme_walk_bus(struct pci_bus *bus)
+{
+	struct pci_dev *dev;
+	bool ret = false;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		/* Skip PCIe devices in case we started from a root port. */
+		if (!pci_is_pcie(dev) && pci_check_pme_status(dev)) {
+			pm_request_resume(&dev->dev);
+			ret = true;
+		}
+
+		if (dev->subordinate && pcie_pme_walk_bus(dev->subordinate))
+			ret = true;
+	}
+
+	return ret;
+}
+
+/**
+ * pcie_pme_from_pci_bridge - Check if PCIe-PCI bridge generated a PME.
+ * @bus: Secondary bus of the bridge.
+ * @devfn: Device/function number to check.
+ *
+ * PME from PCI devices under a PCIe-PCI bridge may be converted to an in-band
+ * PCIe PME message.  In such that case the bridge should use the Requester ID
+ * of device/function number 0 on its secondary bus.
+ */
+static bool pcie_pme_from_pci_bridge(struct pci_bus *bus, u8 devfn)
+{
+	struct pci_dev *dev;
+	bool found = false;
+
+	if (devfn)
+		return false;
+
+	dev = pci_dev_get(bus->self);
+	if (!dev)
+		return false;
+
+	if (pci_is_pcie(dev) && dev->pcie_type == PCI_EXP_TYPE_PCI_BRIDGE) {
+		down_read(&pci_bus_sem);
+		if (pcie_pme_walk_bus(bus))
+			found = true;
+		up_read(&pci_bus_sem);
+	}
+
+	pci_dev_put(dev);
+	return found;
+}
+
+/**
+ * pcie_pme_handle_request - Find device that generated PME and handle it.
+ * @port: Root port or event collector that generated the PME interrupt.
+ * @req_id: PCIe Requester ID of the device that generated the PME.
+ */
+static void pcie_pme_handle_request(struct pci_dev *port, u16 req_id)
+{
+	u8 busnr = req_id >> 8, devfn = req_id & 0xff;
+	struct pci_bus *bus;
+	struct pci_dev *dev;
+	bool found = false;
+
+	/* First, check if the PME is from the root port itself. */
+	if (port->devfn == devfn && port->bus->number == busnr) {
+		if (pci_check_pme_status(port)) {
+			pm_request_resume(&port->dev);
+			found = true;
+		} else {
+			/*
+			 * Apparently, the root port generated the PME on behalf
+			 * of a non-PCIe device downstream.  If this is done by
+			 * a root port, the Requester ID field in its status
+			 * register may contain either the root port's, or the
+			 * source device's information (PCI Express Base
+			 * Specification, Rev. 2.0, Section 6.1.9).
+			 */
+			down_read(&pci_bus_sem);
+			found = pcie_pme_walk_bus(port->subordinate);
+			up_read(&pci_bus_sem);
+		}
+		goto out;
+	}
+
+	/* Second, find the bus the source device is on. */
+	bus = pci_find_bus(pci_domain_nr(port->bus), busnr);
+	if (!bus)
+		goto out;
+
+	/* Next, check if the PME is from a PCIe-PCI bridge. */
+	found = pcie_pme_from_pci_bridge(bus, devfn);
+	if (found)
+		goto out;
+
+	/* Finally, try to find the PME source on the bus. */
+	down_read(&pci_bus_sem);
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		pci_dev_get(dev);
+		if (dev->devfn == devfn) {
+			found = true;
+			break;
+		}
+		pci_dev_put(dev);
+	}
+	up_read(&pci_bus_sem);
+
+	if (found) {
+		/* The device is there, but we have to check its PME status. */
+		found = pci_check_pme_status(dev);
+		if (found)
+			pm_request_resume(&dev->dev);
+		pci_dev_put(dev);
+	} else if (devfn) {
+		/*
+		 * The device is not there, but we can still try to recover by
+		 * assuming that the PME was reported by a PCIe-PCI bridge that
+		 * used devfn different from zero.
+		 */
+		dev_dbg(&port->dev, "PME interrupt generated for "
+			"non-existent device %02x:%02x.%d\n",
+			busnr, PCI_SLOT(devfn), PCI_FUNC(devfn));
+		found = pcie_pme_from_pci_bridge(bus, 0);
+	}
+
+ out:
+	if (!found)
+		dev_dbg(&port->dev, "Spurious native PME interrupt!\n");
+}
+
+/**
+ * pcie_pme_work_fn - Work handler for PCIe PME interrupt.
+ * @work: Work structure giving access to service data.
+ */
+static void pcie_pme_work_fn(struct work_struct *work)
+{
+	struct pcie_pme_service_data *data =
+			container_of(work, struct pcie_pme_service_data, work);
+	struct pci_dev *port = data->srv->port;
+	int rtsta_pos;
+	u32 rtsta;
+
+	rtsta_pos = pci_pcie_cap(port) + PCI_EXP_RTSTA;
+
+	spin_lock_irq(&data->lock);
+
+	for (;;) {
+		if (data->noirq)
+			break;
+
+		pci_read_config_dword(port, rtsta_pos, &rtsta);
+		if (rtsta & PCI_EXP_RTSTA_PME) {
+			/*
+			 * Clear PME status of the port.  If there are other
+			 * pending PMEs, the status will be set again.
+			 */
+			pcie_pme_clear_status(port);
+
+			spin_unlock_irq(&data->lock);
+			pcie_pme_handle_request(port, rtsta & 0xffff);
+			spin_lock_irq(&data->lock);
+
+			continue;
+		}
+
+		/* No need to loop if there are no more PMEs pending. */
+		if (!(rtsta & PCI_EXP_RTSTA_PENDING))
+			break;
+
+		spin_unlock_irq(&data->lock);
+		cpu_relax();
+		spin_lock_irq(&data->lock);
+	}
+
+	if (!data->noirq)
+		pcie_pme_interrupt_enable(port, true);
+
+	spin_unlock_irq(&data->lock);
+}
+
+/**
+ * pcie_pme_irq - Interrupt handler for PCIe root port PME interrupt.
+ * @irq: Interrupt vector.
+ * @context: Interrupt context pointer.
+ */
+static irqreturn_t pcie_pme_irq(int irq, void *context)
+{
+	struct pci_dev *port;
+	struct pcie_pme_service_data *data;
+	int rtsta_pos;
+	u32 rtsta;
+	unsigned long flags;
+
+	port = ((struct pcie_device *)context)->port;
+	data = get_service_data((struct pcie_device *)context);
+
+	rtsta_pos = pci_pcie_cap(port) + PCI_EXP_RTSTA;
+
+	spin_lock_irqsave(&data->lock, flags);
+	pci_read_config_dword(port, rtsta_pos, &rtsta);
+
+	if (!(rtsta & PCI_EXP_RTSTA_PME)) {
+		spin_unlock_irqrestore(&data->lock, flags);
+		return IRQ_NONE;
+	}
+
+	pcie_pme_interrupt_enable(port, false);
+	spin_unlock_irqrestore(&data->lock, flags);
+
+	/* We don't use pm_wq, because it's freezable. */
+	schedule_work(&data->work);
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * pcie_pme_set_native - Set the PME interrupt flag for given device.
+ * @dev: PCI device to handle.
+ * @ign: Ignored.
+ */
+static int pcie_pme_set_native(struct pci_dev *dev, void *ign)
+{
+	dev_info(&dev->dev, "Signaling PME through PCIe PME interrupt\n");
+
+	device_set_run_wake(&dev->dev, true);
+	dev->pme_interrupt = true;
+	return 0;
+}
+
+/**
+ * pcie_pme_mark_devices - Set the PME interrupt flag for devices below a port.
+ * @port: PCIe root port or event collector to handle.
+ *
+ * For each device below given root port, including the port itself (or for each
+ * root complex integrated endpoint if @port is a root complex event collector)
+ * set the flag indicating that it can signal run-time wake-up events via PCIe
+ * PME interrupts.
+ */
+static void pcie_pme_mark_devices(struct pci_dev *port)
+{
+	pcie_pme_set_native(port, NULL);
+	if (port->subordinate) {
+		pci_walk_bus(port->subordinate, pcie_pme_set_native, NULL);
+	} else {
+		struct pci_bus *bus = port->bus;
+		struct pci_dev *dev;
+
+		/* Check if this is a root port event collector. */
+		if (port->pcie_type != PCI_EXP_TYPE_RC_EC || !bus)
+			return;
+
+		down_read(&pci_bus_sem);
+		list_for_each_entry(dev, &bus->devices, bus_list)
+			if (pci_is_pcie(dev)
+			    && dev->pcie_type == PCI_EXP_TYPE_RC_END)
+				pcie_pme_set_native(dev, NULL);
+		up_read(&pci_bus_sem);
+	}
+}
+
+/**
+ * pcie_pme_probe - Initialize PCIe PME service for given root port.
+ * @srv: PCIe service to initialize.
+ */
+static int pcie_pme_probe(struct pcie_device *srv)
+{
+	struct pci_dev *port;
+	struct pcie_pme_service_data *data;
+	int ret;
+
+	if (!pcie_pme_platform_setup(srv))
+		return -EACCES;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	spin_lock_init(&data->lock);
+	INIT_WORK(&data->work, pcie_pme_work_fn);
+	data->srv = srv;
+	set_service_data(srv, data);
+
+	port = srv->port;
+	pcie_pme_interrupt_enable(port, false);
+	pcie_pme_clear_status(port);
+
+	ret = request_irq(srv->irq, pcie_pme_irq, IRQF_SHARED, "PCIe PME", srv);
+	if (ret) {
+		kfree(data);
+	} else {
+		pcie_pme_mark_devices(port);
+		pcie_pme_interrupt_enable(port, true);
+	}
+
+	return ret;
+}
+
+/**
+ * pcie_pme_suspend - Suspend PCIe PME service device.
+ * @srv: PCIe service device to suspend.
+ */
+static int pcie_pme_suspend(struct pcie_device *srv)
+{
+	struct pcie_pme_service_data *data = get_service_data(srv);
+	struct pci_dev *port = srv->port;
+
+	spin_lock_irq(&data->lock);
+	pcie_pme_interrupt_enable(port, false);
+	pcie_pme_clear_status(port);
+	data->noirq = true;
+	spin_unlock_irq(&data->lock);
+
+	synchronize_irq(srv->irq);
+
+	return 0;
+}
+
+/**
+ * pcie_pme_resume - Resume PCIe PME service device.
+ * @srv - PCIe service device to resume.
+ */
+static int pcie_pme_resume(struct pcie_device *srv)
+{
+	struct pcie_pme_service_data *data = get_service_data(srv);
+	struct pci_dev *port = srv->port;
+
+	spin_lock_irq(&data->lock);
+	data->noirq = false;
+	pcie_pme_clear_status(port);
+	pcie_pme_interrupt_enable(port, true);
+	spin_unlock_irq(&data->lock);
+
+	return 0;
+}
+
+/**
+ * pcie_pme_remove - Prepare PCIe PME service device for removal.
+ * @srv - PCIe service device to resume.
+ */
+static void pcie_pme_remove(struct pcie_device *srv)
+{
+	pcie_pme_suspend(srv);
+	free_irq(srv->irq, srv);
+	kfree(get_service_data(srv));
+}
+
+static struct pcie_port_service_driver pcie_pme_driver = {
+	.name		= "pcie_pme",
+	.port_type 	= PCI_EXP_TYPE_ROOT_PORT,
+	.service 	= PCIE_PORT_SERVICE_PME,
+
+	.probe		= pcie_pme_probe,
+	.suspend	= pcie_pme_suspend,
+	.resume		= pcie_pme_resume,
+	.remove		= pcie_pme_remove,
+};
+
+/**
+ * pcie_pme_service_init - Register the PCIe PME service driver.
+ */
+static int __init pcie_pme_service_init(void)
+{
+	return pcie_pme_disabled ?
+		-ENODEV : pcie_port_service_register(&pcie_pme_driver);
+}
+
+module_init(pcie_pme_service_init);
diff --git a/drivers/pci/pcie/pme/pcie_pme.h b/drivers/pci/pcie/pme/pcie_pme.h
new file mode 100644
index 0000000..b30d2b7
--- /dev/null
+++ b/drivers/pci/pcie/pme/pcie_pme.h
@@ -0,0 +1,28 @@
+/*
+ * drivers/pci/pcie/pme/pcie_pme.h
+ *
+ * PCI Express Root Port PME signaling support
+ *
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ */
+
+#ifndef _PCIE_PME_H_
+#define _PCIE_PME_H_
+
+struct pcie_device;
+
+#ifdef CONFIG_ACPI
+extern int pcie_pme_acpi_setup(struct pcie_device *srv);
+
+static inline int pcie_pme_platform_notify(struct pcie_device *srv)
+{
+	return pcie_pme_acpi_setup(srv);
+}
+#else /* !CONFIG_ACPI */
+static inline int pcie_pme_platform_notify(struct pcie_device *srv)
+{
+	return 0;
+}
+#endif /* !CONFIG_ACPI */
+
+#endif
diff --git a/drivers/pci/pcie/pme/pcie_pme_acpi.c b/drivers/pci/pcie/pme/pcie_pme_acpi.c
new file mode 100644
index 0000000..83ab228
--- /dev/null
+++ b/drivers/pci/pcie/pme/pcie_pme_acpi.c
@@ -0,0 +1,54 @@
+/*
+ * PCIe Native PME support, ACPI-related part
+ *
+ * Copyright (C) 2009 Rafael J. Wysocki <rjw@sisk.pl>, Novell Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License V2.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/pci.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/acpi.h>
+#include <linux/pci-acpi.h>
+#include <linux/pcieport_if.h>
+
+/**
+ * pcie_pme_acpi_setup - Request the ACPI BIOS to release control over PCIe PME.
+ * @srv - PCIe PME service for a root port or event collector.
+ *
+ * Invoked when the PCIe bus type loads PCIe PME service driver.  To avoid
+ * conflict with the BIOS PCIe support requires the BIOS to yield PCIe PME
+ * control to the kernel.
+ */
+int pcie_pme_acpi_setup(struct pcie_device *srv)
+{
+	acpi_status status = AE_NOT_FOUND;
+	struct pci_dev *port = srv->port;
+	acpi_handle handle;
+	int error = 0;
+
+	if (acpi_pci_disabled)
+		return -ENOSYS;
+
+	dev_info(&port->dev, "Requesting control of PCIe PME from ACPI BIOS\n");
+
+	handle = acpi_find_root_bridge_handle(port);
+	if (!handle)
+		return -EINVAL;
+
+	status = acpi_pci_osc_control_set(handle,
+			OSC_PCI_EXPRESS_PME_CONTROL |
+			OSC_PCI_EXPRESS_CAP_STRUCTURE_CONTROL);
+	if (ACPI_FAILURE(status)) {
+		dev_info(&port->dev,
+			"Failed to receive control of PCIe PME service: %s\n",
+			(status == AE_SUPPORT || status == AE_NOT_FOUND) ?
+			"no _OSC support" : "ACPI _OSC failed");
+		error = -ENODEV;
+	}
+
+	return error;
+}
diff --git a/drivers/pci/pcie/portdrv.h b/drivers/pci/pcie/portdrv.h
index aaeb9d2..813a5c3 100644
--- a/drivers/pci/pcie/portdrv.h
+++ b/drivers/pci/pcie/portdrv.h
@@ -30,4 +30,21 @@
 extern int __must_check pcie_port_bus_register(void);
 extern void pcie_port_bus_unregister(void);
 
+#ifdef CONFIG_PCIE_PME
+extern bool pcie_pme_msi_disabled;
+
+static inline void pcie_pme_disable_msi(void)
+{
+	pcie_pme_msi_disabled = true;
+}
+
+static inline bool pcie_pme_no_msi(void)
+{
+	return pcie_pme_msi_disabled;
+}
+#else /* !CONFIG_PCIE_PME */
+static inline void pcie_pme_disable_msi(void) {}
+static inline bool pcie_pme_no_msi(void) { return false; }
+#endif /* !CONFIG_PCIE_PME */
+
 #endif /* _PORTDRV_H_ */
diff --git a/drivers/pci/pcie/portdrv_core.c b/drivers/pci/pcie/portdrv_core.c
index b174188..0d34ff4 100644
--- a/drivers/pci/pcie/portdrv_core.c
+++ b/drivers/pci/pcie/portdrv_core.c
@@ -186,16 +186,24 @@
  */
 static int init_service_irqs(struct pci_dev *dev, int *irqs, int mask)
 {
-	int i, irq;
+	int i, irq = -1;
+
+	/* We have to use INTx if MSI cannot be used for PCIe PME. */
+	if ((mask & PCIE_PORT_SERVICE_PME) && pcie_pme_no_msi()) {
+		if (dev->pin)
+			irq = dev->irq;
+		goto no_msi;
+	}
 
 	/* Try to use MSI-X if supported */
 	if (!pcie_port_enable_msix(dev, irqs, mask))
 		return 0;
+
 	/* We're not going to use MSI-X, so try MSI and fall back to INTx */
-	irq = -1;
 	if (!pci_enable_msi(dev) || dev->pin)
 		irq = dev->irq;
 
+ no_msi:
 	for (i = 0; i < PCIE_PORT_DEVICE_MAXSERVICES; i++)
 		irqs[i] = irq;
 	irqs[PCIE_PORT_SERVICE_VC_SHIFT] = -1;
diff --git a/drivers/pci/pcie/portdrv_pci.c b/drivers/pci/pcie/portdrv_pci.c
index 13c8972..127e8f1 100644
--- a/drivers/pci/pcie/portdrv_pci.c
+++ b/drivers/pci/pcie/portdrv_pci.c
@@ -15,6 +15,7 @@
 #include <linux/slab.h>
 #include <linux/pcieport_if.h>
 #include <linux/aer.h>
+#include <linux/dmi.h>
 
 #include "portdrv.h"
 #include "aer/aerdrv.h"
@@ -273,10 +274,36 @@
 	.driver.pm 	= PCIE_PORTDRV_PM_OPS,
 };
 
+static int __init dmi_pcie_pme_disable_msi(const struct dmi_system_id *d)
+{
+	pr_notice("%s detected: will not use MSI for PCIe PME signaling\n",
+			d->ident);
+	pcie_pme_disable_msi();
+	return 0;
+}
+
+static struct dmi_system_id __initdata pcie_portdrv_dmi_table[] = {
+	/*
+	 * Boxes that should not use MSI for PCIe PME signaling.
+	 */
+	{
+	 .callback = dmi_pcie_pme_disable_msi,
+	 .ident = "MSI Wind U-100",
+	 .matches = {
+		     DMI_MATCH(DMI_SYS_VENDOR,
+		     		"MICRO-STAR INTERNATIONAL CO., LTD"),
+		     DMI_MATCH(DMI_PRODUCT_NAME, "U-100"),
+		     },
+	 },
+	 {}
+};
+
 static int __init pcie_portdrv_init(void)
 {
 	int retval;
 
+	dmi_check_system(pcie_portdrv_dmi_table);
+
 	retval = pcie_port_bus_register();
 	if (retval) {
 		printk(KERN_WARNING "PCIE: bus_register error: %d\n", retval);
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 446e4a9..270d069 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -89,6 +89,7 @@
 
 	if (pci_bus->bridge)
 		put_device(pci_bus->bridge);
+	pci_bus_remove_resources(pci_bus);
 	kfree(pci_bus);
 }
 
@@ -281,26 +282,12 @@
 	}
 }
 
-void __devinit pci_read_bridge_bases(struct pci_bus *child)
+static void __devinit pci_read_bridge_io(struct pci_bus *child)
 {
 	struct pci_dev *dev = child->self;
 	u8 io_base_lo, io_limit_lo;
-	u16 mem_base_lo, mem_limit_lo;
 	unsigned long base, limit;
 	struct resource *res;
-	int i;
-
-	if (pci_is_root_bus(child))	/* It's a host bus, nothing to read */
-		return;
-
-	dev_info(&dev->dev, "PCI bridge to [bus %02x-%02x]%s\n",
-		 child->secondary, child->subordinate,
-		 dev->transparent ? " (subtractive decode)": "");
-
-	if (dev->transparent) {
-		for(i = 3; i < PCI_BUS_NUM_RESOURCES; i++)
-			child->resource[i] = child->parent->resource[i - 3];
-	}
 
 	res = child->resource[0];
 	pci_read_config_byte(dev, PCI_IO_BASE, &io_base_lo);
@@ -316,26 +303,50 @@
 		limit |= (io_limit_hi << 16);
 	}
 
-	if (base <= limit) {
+	if (base && base <= limit) {
 		res->flags = (io_base_lo & PCI_IO_RANGE_TYPE_MASK) | IORESOURCE_IO;
 		if (!res->start)
 			res->start = base;
 		if (!res->end)
 			res->end = limit + 0xfff;
 		dev_printk(KERN_DEBUG, &dev->dev, "  bridge window %pR\n", res);
+	} else {
+		dev_printk(KERN_DEBUG, &dev->dev,
+			 "  bridge window [io  %04lx - %04lx] reg reading\n",
+				 base, limit);
 	}
+}
+
+static void __devinit pci_read_bridge_mmio(struct pci_bus *child)
+{
+	struct pci_dev *dev = child->self;
+	u16 mem_base_lo, mem_limit_lo;
+	unsigned long base, limit;
+	struct resource *res;
 
 	res = child->resource[1];
 	pci_read_config_word(dev, PCI_MEMORY_BASE, &mem_base_lo);
 	pci_read_config_word(dev, PCI_MEMORY_LIMIT, &mem_limit_lo);
 	base = (mem_base_lo & PCI_MEMORY_RANGE_MASK) << 16;
 	limit = (mem_limit_lo & PCI_MEMORY_RANGE_MASK) << 16;
-	if (base <= limit) {
+	if (base && base <= limit) {
 		res->flags = (mem_base_lo & PCI_MEMORY_RANGE_TYPE_MASK) | IORESOURCE_MEM;
 		res->start = base;
 		res->end = limit + 0xfffff;
 		dev_printk(KERN_DEBUG, &dev->dev, "  bridge window %pR\n", res);
+	} else {
+		dev_printk(KERN_DEBUG, &dev->dev,
+			"  bridge window [mem 0x%08lx - 0x%08lx] reg reading\n",
+					 base, limit + 0xfffff);
 	}
+}
+
+static void __devinit pci_read_bridge_mmio_pref(struct pci_bus *child)
+{
+	struct pci_dev *dev = child->self;
+	u16 mem_base_lo, mem_limit_lo;
+	unsigned long base, limit;
+	struct resource *res;
 
 	res = child->resource[2];
 	pci_read_config_word(dev, PCI_PREF_MEMORY_BASE, &mem_base_lo);
@@ -366,7 +377,7 @@
 #endif
 		}
 	}
-	if (base <= limit) {
+	if (base && base <= limit) {
 		res->flags = (mem_base_lo & PCI_PREF_RANGE_TYPE_MASK) |
 					 IORESOURCE_MEM | IORESOURCE_PREFETCH;
 		if (res->flags & PCI_PREF_RANGE_TYPE_64)
@@ -374,6 +385,44 @@
 		res->start = base;
 		res->end = limit + 0xfffff;
 		dev_printk(KERN_DEBUG, &dev->dev, "  bridge window %pR\n", res);
+	} else {
+		dev_printk(KERN_DEBUG, &dev->dev,
+		     "  bridge window [mem 0x%08lx - %08lx pref] reg reading\n",
+					 base, limit + 0xfffff);
+	}
+}
+
+void __devinit pci_read_bridge_bases(struct pci_bus *child)
+{
+	struct pci_dev *dev = child->self;
+	struct resource *res;
+	int i;
+
+	if (pci_is_root_bus(child))	/* It's a host bus, nothing to read */
+		return;
+
+	dev_info(&dev->dev, "PCI bridge to [bus %02x-%02x]%s\n",
+		 child->secondary, child->subordinate,
+		 dev->transparent ? " (subtractive decode)" : "");
+
+	pci_bus_remove_resources(child);
+	for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; i++)
+		child->resource[i] = &dev->resource[PCI_BRIDGE_RESOURCES+i];
+
+	pci_read_bridge_io(child);
+	pci_read_bridge_mmio(child);
+	pci_read_bridge_mmio_pref(child);
+
+	if (dev->transparent) {
+		pci_bus_for_each_resource(child->parent, res, i) {
+			if (res) {
+				pci_bus_add_resource(child, res,
+						     PCI_SUBTRACTIVE_DECODE);
+				dev_printk(KERN_DEBUG, &dev->dev,
+					   "  bridge window %pR (subtractive decode)\n",
+					   res);
+			}
+		}
 	}
 }
 
@@ -387,10 +436,147 @@
 		INIT_LIST_HEAD(&b->children);
 		INIT_LIST_HEAD(&b->devices);
 		INIT_LIST_HEAD(&b->slots);
+		INIT_LIST_HEAD(&b->resources);
+		b->max_bus_speed = PCI_SPEED_UNKNOWN;
+		b->cur_bus_speed = PCI_SPEED_UNKNOWN;
 	}
 	return b;
 }
 
+static unsigned char pcix_bus_speed[] = {
+	PCI_SPEED_UNKNOWN,		/* 0 */
+	PCI_SPEED_66MHz_PCIX,		/* 1 */
+	PCI_SPEED_100MHz_PCIX,		/* 2 */
+	PCI_SPEED_133MHz_PCIX,		/* 3 */
+	PCI_SPEED_UNKNOWN,		/* 4 */
+	PCI_SPEED_66MHz_PCIX_ECC,	/* 5 */
+	PCI_SPEED_100MHz_PCIX_ECC,	/* 6 */
+	PCI_SPEED_133MHz_PCIX_ECC,	/* 7 */
+	PCI_SPEED_UNKNOWN,		/* 8 */
+	PCI_SPEED_66MHz_PCIX_266,	/* 9 */
+	PCI_SPEED_100MHz_PCIX_266,	/* A */
+	PCI_SPEED_133MHz_PCIX_266,	/* B */
+	PCI_SPEED_UNKNOWN,		/* C */
+	PCI_SPEED_66MHz_PCIX_533,	/* D */
+	PCI_SPEED_100MHz_PCIX_533,	/* E */
+	PCI_SPEED_133MHz_PCIX_533	/* F */
+};
+
+static unsigned char pcie_link_speed[] = {
+	PCI_SPEED_UNKNOWN,		/* 0 */
+	PCIE_SPEED_2_5GT,		/* 1 */
+	PCIE_SPEED_5_0GT,		/* 2 */
+	PCIE_SPEED_8_0GT,		/* 3 */
+	PCI_SPEED_UNKNOWN,		/* 4 */
+	PCI_SPEED_UNKNOWN,		/* 5 */
+	PCI_SPEED_UNKNOWN,		/* 6 */
+	PCI_SPEED_UNKNOWN,		/* 7 */
+	PCI_SPEED_UNKNOWN,		/* 8 */
+	PCI_SPEED_UNKNOWN,		/* 9 */
+	PCI_SPEED_UNKNOWN,		/* A */
+	PCI_SPEED_UNKNOWN,		/* B */
+	PCI_SPEED_UNKNOWN,		/* C */
+	PCI_SPEED_UNKNOWN,		/* D */
+	PCI_SPEED_UNKNOWN,		/* E */
+	PCI_SPEED_UNKNOWN		/* F */
+};
+
+void pcie_update_link_speed(struct pci_bus *bus, u16 linksta)
+{
+	bus->cur_bus_speed = pcie_link_speed[linksta & 0xf];
+}
+EXPORT_SYMBOL_GPL(pcie_update_link_speed);
+
+static unsigned char agp_speeds[] = {
+	AGP_UNKNOWN,
+	AGP_1X,
+	AGP_2X,
+	AGP_4X,
+	AGP_8X
+};
+
+static enum pci_bus_speed agp_speed(int agp3, int agpstat)
+{
+	int index = 0;
+
+	if (agpstat & 4)
+		index = 3;
+	else if (agpstat & 2)
+		index = 2;
+	else if (agpstat & 1)
+		index = 1;
+	else
+		goto out;
+	
+	if (agp3) {
+		index += 2;
+		if (index == 5)
+			index = 0;
+	}
+
+ out:
+	return agp_speeds[index];
+}
+
+
+static void pci_set_bus_speed(struct pci_bus *bus)
+{
+	struct pci_dev *bridge = bus->self;
+	int pos;
+
+	pos = pci_find_capability(bridge, PCI_CAP_ID_AGP);
+	if (!pos)
+		pos = pci_find_capability(bridge, PCI_CAP_ID_AGP3);
+	if (pos) {
+		u32 agpstat, agpcmd;
+
+		pci_read_config_dword(bridge, pos + PCI_AGP_STATUS, &agpstat);
+		bus->max_bus_speed = agp_speed(agpstat & 8, agpstat & 7);
+
+		pci_read_config_dword(bridge, pos + PCI_AGP_COMMAND, &agpcmd);
+		bus->cur_bus_speed = agp_speed(agpstat & 8, agpcmd & 7);
+	}
+
+	pos = pci_find_capability(bridge, PCI_CAP_ID_PCIX);
+	if (pos) {
+		u16 status;
+		enum pci_bus_speed max;
+		pci_read_config_word(bridge, pos + 2, &status);
+
+		if (status & 0x8000) {
+			max = PCI_SPEED_133MHz_PCIX_533;
+		} else if (status & 0x4000) {
+			max = PCI_SPEED_133MHz_PCIX_266;
+		} else if (status & 0x0002) {
+			if (((status >> 12) & 0x3) == 2) {
+				max = PCI_SPEED_133MHz_PCIX_ECC;
+			} else {
+				max = PCI_SPEED_133MHz_PCIX;
+			}
+		} else {
+			max = PCI_SPEED_66MHz_PCIX;
+		}
+
+		bus->max_bus_speed = max;
+		bus->cur_bus_speed = pcix_bus_speed[(status >> 6) & 0xf];
+
+		return;
+	}
+
+	pos = pci_find_capability(bridge, PCI_CAP_ID_EXP);
+	if (pos) {
+		u32 linkcap;
+		u16 linksta;
+
+		pci_read_config_dword(bridge, pos + PCI_EXP_LNKCAP, &linkcap);
+		bus->max_bus_speed = pcie_link_speed[linkcap & 0xf];
+
+		pci_read_config_word(bridge, pos + PCI_EXP_LNKSTA, &linksta);
+		pcie_update_link_speed(bus, linksta);
+	}
+}
+
+
 static struct pci_bus *pci_alloc_child_bus(struct pci_bus *parent,
 					   struct pci_dev *bridge, int busnr)
 {
@@ -430,6 +616,8 @@
 	child->self = bridge;
 	child->bridge = get_device(&bridge->dev);
 
+	pci_set_bus_speed(child);
+
 	/* Set up default resource pointers and names.. */
 	for (i = 0; i < PCI_BRIDGE_RESOURCE_NUM; i++) {
 		child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
@@ -1081,6 +1269,45 @@
 }
 EXPORT_SYMBOL(pci_scan_single_device);
 
+static unsigned next_ari_fn(struct pci_dev *dev, unsigned fn)
+{
+	u16 cap;
+	unsigned pos, next_fn;
+
+	if (!dev)
+		return 0;
+
+	pos = pci_find_ext_capability(dev, PCI_EXT_CAP_ID_ARI);
+	if (!pos)
+		return 0;
+	pci_read_config_word(dev, pos + 4, &cap);
+	next_fn = cap >> 8;
+	if (next_fn <= fn)
+		return 0;
+	return next_fn;
+}
+
+static unsigned next_trad_fn(struct pci_dev *dev, unsigned fn)
+{
+	return (fn + 1) % 8;
+}
+
+static unsigned no_next_fn(struct pci_dev *dev, unsigned fn)
+{
+	return 0;
+}
+
+static int only_one_child(struct pci_bus *bus)
+{
+	struct pci_dev *parent = bus->self;
+	if (!parent || !pci_is_pcie(parent))
+		return 0;
+	if (parent->pcie_type == PCI_EXP_TYPE_ROOT_PORT ||
+	    parent->pcie_type == PCI_EXP_TYPE_DOWNSTREAM)
+		return 1;
+	return 0;
+}
+
 /**
  * pci_scan_slot - scan a PCI slot on a bus for devices.
  * @bus: PCI bus to scan
@@ -1094,21 +1321,30 @@
  */
 int pci_scan_slot(struct pci_bus *bus, int devfn)
 {
-	int fn, nr = 0;
+	unsigned fn, nr = 0;
 	struct pci_dev *dev;
+	unsigned (*next_fn)(struct pci_dev *, unsigned) = no_next_fn;
+
+	if (only_one_child(bus) && (devfn > 0))
+		return 0; /* Already scanned the entire slot */
 
 	dev = pci_scan_single_device(bus, devfn);
-	if (dev && !dev->is_added)	/* new device? */
+	if (!dev)
+		return 0;
+	if (!dev->is_added)
 		nr++;
 
-	if (dev && dev->multifunction) {
-		for (fn = 1; fn < 8; fn++) {
-			dev = pci_scan_single_device(bus, devfn + fn);
-			if (dev) {
-				if (!dev->is_added)
-					nr++;
-				dev->multifunction = 1;
-			}
+	if (pci_ari_enabled(bus))
+		next_fn = next_ari_fn;
+	else if (dev->multifunction)
+		next_fn = next_trad_fn;
+
+	for (fn = next_fn(dev, 0); fn > 0; fn = next_fn(dev, fn)) {
+		dev = pci_scan_single_device(bus, devfn + fn);
+		if (dev) {
+			if (!dev->is_added)
+				nr++;
+			dev->multifunction = 1;
 		}
 	}
 
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index d58b940..790eb69 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -25,14 +25,9 @@
 #include <linux/dmi.h>
 #include <linux/pci-aspm.h>
 #include <linux/ioport.h>
+#include <asm/dma.h>	/* isa_dma_bridge_buggy */
 #include "pci.h"
 
-int isa_dma_bridge_buggy;
-EXPORT_SYMBOL(isa_dma_bridge_buggy);
-int pci_pci_problems;
-EXPORT_SYMBOL(pci_pci_problems);
-
-#ifdef CONFIG_PCI_QUIRKS
 /*
  * This quirk function disables memory decoding and releases memory resources
  * of the device specified by kernel's boot parameter 'pci=resource_alignment='.
@@ -2612,6 +2607,7 @@
 	}
 	pci_do_fixups(dev, start, end);
 }
+EXPORT_SYMBOL(pci_fixup_device);
 
 static int __init pci_apply_final_quirks(void)
 {
@@ -2723,9 +2719,3 @@
 
 	return -ENOTTY;
 }
-
-#else
-void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) {}
-int pci_dev_specific_reset(struct pci_dev *dev, int probe) { return -ENOTTY; }
-#endif
-EXPORT_SYMBOL(pci_fixup_device);
diff --git a/drivers/pci/setup-bus.c b/drivers/pci/setup-bus.c
index c48cd37..bf32f07 100644
--- a/drivers/pci/setup-bus.c
+++ b/drivers/pci/setup-bus.c
@@ -27,37 +27,83 @@
 #include <linux/slab.h>
 #include "pci.h"
 
-static void pbus_assign_resources_sorted(const struct pci_bus *bus)
-{
-	struct pci_dev *dev;
+struct resource_list_x {
+	struct resource_list_x *next;
 	struct resource *res;
-	struct resource_list head, *list, *tmp;
-	int idx;
+	struct pci_dev *dev;
+	resource_size_t start;
+	resource_size_t end;
+	unsigned long flags;
+};
 
-	head.next = NULL;
-	list_for_each_entry(dev, &bus->devices, bus_list) {
-		u16 class = dev->class >> 8;
+static void add_to_failed_list(struct resource_list_x *head,
+				 struct pci_dev *dev, struct resource *res)
+{
+	struct resource_list_x *list = head;
+	struct resource_list_x *ln = list->next;
+	struct resource_list_x *tmp;
 
-		/* Don't touch classless devices or host bridges or ioapics.  */
-		if (class == PCI_CLASS_NOT_DEFINED ||
-		    class == PCI_CLASS_BRIDGE_HOST)
-			continue;
-
-		/* Don't touch ioapic devices already enabled by firmware */
-		if (class == PCI_CLASS_SYSTEM_PIC) {
-			u16 command;
-			pci_read_config_word(dev, PCI_COMMAND, &command);
-			if (command & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY))
-				continue;
-		}
-
-		pdev_sort_resources(dev, &head);
+	tmp = kmalloc(sizeof(*tmp), GFP_KERNEL);
+	if (!tmp) {
+		pr_warning("add_to_failed_list: kmalloc() failed!\n");
+		return;
 	}
 
-	for (list = head.next; list;) {
+	tmp->next = ln;
+	tmp->res = res;
+	tmp->dev = dev;
+	tmp->start = res->start;
+	tmp->end = res->end;
+	tmp->flags = res->flags;
+	list->next = tmp;
+}
+
+static void free_failed_list(struct resource_list_x *head)
+{
+	struct resource_list_x *list, *tmp;
+
+	for (list = head->next; list;) {
+		tmp = list;
+		list = list->next;
+		kfree(tmp);
+	}
+
+	head->next = NULL;
+}
+
+static void __dev_sort_resources(struct pci_dev *dev,
+				 struct resource_list *head)
+{
+	u16 class = dev->class >> 8;
+
+	/* Don't touch classless devices or host bridges or ioapics.  */
+	if (class == PCI_CLASS_NOT_DEFINED || class == PCI_CLASS_BRIDGE_HOST)
+		return;
+
+	/* Don't touch ioapic devices already enabled by firmware */
+	if (class == PCI_CLASS_SYSTEM_PIC) {
+		u16 command;
+		pci_read_config_word(dev, PCI_COMMAND, &command);
+		if (command & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY))
+			return;
+	}
+
+	pdev_sort_resources(dev, head);
+}
+
+static void __assign_resources_sorted(struct resource_list *head,
+				 struct resource_list_x *fail_head)
+{
+	struct resource *res;
+	struct resource_list *list, *tmp;
+	int idx;
+
+	for (list = head->next; list;) {
 		res = list->res;
 		idx = res - &list->dev->resource[0];
 		if (pci_assign_resource(list->dev, idx)) {
+			if (fail_head && !pci_is_root_bus(list->dev->bus))
+				add_to_failed_list(fail_head, list->dev, res);
 			res->start = 0;
 			res->end = 0;
 			res->flags = 0;
@@ -68,6 +114,30 @@
 	}
 }
 
+static void pdev_assign_resources_sorted(struct pci_dev *dev,
+				 struct resource_list_x *fail_head)
+{
+	struct resource_list head;
+
+	head.next = NULL;
+	__dev_sort_resources(dev, &head);
+	__assign_resources_sorted(&head, fail_head);
+
+}
+
+static void pbus_assign_resources_sorted(const struct pci_bus *bus,
+					 struct resource_list_x *fail_head)
+{
+	struct pci_dev *dev;
+	struct resource_list head;
+
+	head.next = NULL;
+	list_for_each_entry(dev, &bus->devices, bus_list)
+		__dev_sort_resources(dev, &head);
+
+	__assign_resources_sorted(&head, fail_head);
+}
+
 void pci_setup_cardbus(struct pci_bus *bus)
 {
 	struct pci_dev *bridge = bus->self;
@@ -134,18 +204,12 @@
    config space writes, so it's quite possible that an I/O window of
    the bridge will have some undesirable address (e.g. 0) after the
    first write. Ditto 64-bit prefetchable MMIO.  */
-static void pci_setup_bridge(struct pci_bus *bus)
+static void pci_setup_bridge_io(struct pci_bus *bus)
 {
 	struct pci_dev *bridge = bus->self;
 	struct resource *res;
 	struct pci_bus_region region;
-	u32 l, bu, lu, io_upper16;
-
-	if (pci_is_enabled(bridge))
-		return;
-
-	dev_info(&bridge->dev, "PCI bridge to [bus %02x-%02x]\n",
-		 bus->secondary, bus->subordinate);
+	u32 l, io_upper16;
 
 	/* Set up the top and bottom of the PCI I/O segment for this bus. */
 	res = bus->resource[0];
@@ -158,8 +222,7 @@
 		/* Set up upper 16 bits of I/O base/limit. */
 		io_upper16 = (region.end & 0xffff0000) | (region.start >> 16);
 		dev_info(&bridge->dev, "  bridge window %pR\n", res);
-	}
-	else {
+	} else {
 		/* Clear upper 16 bits of I/O base/limit. */
 		io_upper16 = 0;
 		l = 0x00f0;
@@ -171,21 +234,35 @@
 	pci_write_config_dword(bridge, PCI_IO_BASE, l);
 	/* Update upper 16 bits of I/O base/limit. */
 	pci_write_config_dword(bridge, PCI_IO_BASE_UPPER16, io_upper16);
+}
 
-	/* Set up the top and bottom of the PCI Memory segment
-	   for this bus. */
+static void pci_setup_bridge_mmio(struct pci_bus *bus)
+{
+	struct pci_dev *bridge = bus->self;
+	struct resource *res;
+	struct pci_bus_region region;
+	u32 l;
+
+	/* Set up the top and bottom of the PCI Memory segment for this bus. */
 	res = bus->resource[1];
 	pcibios_resource_to_bus(bridge, &region, res);
 	if (res->flags & IORESOURCE_MEM) {
 		l = (region.start >> 16) & 0xfff0;
 		l |= region.end & 0xfff00000;
 		dev_info(&bridge->dev, "  bridge window %pR\n", res);
-	}
-	else {
+	} else {
 		l = 0x0000fff0;
 		dev_info(&bridge->dev, "  bridge window [mem disabled]\n");
 	}
 	pci_write_config_dword(bridge, PCI_MEMORY_BASE, l);
+}
+
+static void pci_setup_bridge_mmio_pref(struct pci_bus *bus)
+{
+	struct pci_dev *bridge = bus->self;
+	struct resource *res;
+	struct pci_bus_region region;
+	u32 l, bu, lu;
 
 	/* Clear out the upper 32 bits of PREF limit.
 	   If PCI_PREF_BASE_UPPER32 was non-zero, this temporarily
@@ -204,8 +281,7 @@
 			lu = upper_32_bits(region.end);
 		}
 		dev_info(&bridge->dev, "  bridge window %pR\n", res);
-	}
-	else {
+	} else {
 		l = 0x0000fff0;
 		dev_info(&bridge->dev, "  bridge window [mem pref disabled]\n");
 	}
@@ -214,10 +290,35 @@
 	/* Set the upper 32 bits of PREF base & limit. */
 	pci_write_config_dword(bridge, PCI_PREF_BASE_UPPER32, bu);
 	pci_write_config_dword(bridge, PCI_PREF_LIMIT_UPPER32, lu);
+}
+
+static void __pci_setup_bridge(struct pci_bus *bus, unsigned long type)
+{
+	struct pci_dev *bridge = bus->self;
+
+	dev_info(&bridge->dev, "PCI bridge to [bus %02x-%02x]\n",
+		 bus->secondary, bus->subordinate);
+
+	if (type & IORESOURCE_IO)
+		pci_setup_bridge_io(bus);
+
+	if (type & IORESOURCE_MEM)
+		pci_setup_bridge_mmio(bus);
+
+	if (type & IORESOURCE_PREFETCH)
+		pci_setup_bridge_mmio_pref(bus);
 
 	pci_write_config_word(bridge, PCI_BRIDGE_CONTROL, bus->bridge_ctl);
 }
 
+static void pci_setup_bridge(struct pci_bus *bus)
+{
+	unsigned long type = IORESOURCE_IO | IORESOURCE_MEM |
+				  IORESOURCE_PREFETCH;
+
+	__pci_setup_bridge(bus, type);
+}
+
 /* Check whether the bridge supports optional I/O and
    prefetchable memory ranges. If not, the respective
    base/limit registers must be read-only and read as 0. */
@@ -253,8 +354,11 @@
 	}
 	if (pmem) {
 		b_res[2].flags |= IORESOURCE_MEM | IORESOURCE_PREFETCH;
-		if ((pmem & PCI_PREF_RANGE_TYPE_MASK) == PCI_PREF_RANGE_TYPE_64)
+		if ((pmem & PCI_PREF_RANGE_TYPE_MASK) ==
+		    PCI_PREF_RANGE_TYPE_64) {
 			b_res[2].flags |= IORESOURCE_MEM_64;
+			b_res[2].flags |= PCI_PREF_RANGE_TYPE_64;
+		}
 	}
 
 	/* double check if bridge does support 64 bit pref */
@@ -283,8 +387,7 @@
 	unsigned long type_mask = IORESOURCE_IO | IORESOURCE_MEM |
 				  IORESOURCE_PREFETCH;
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		r = bus->resource[i];
+	pci_bus_for_each_resource(bus, r, i) {
 		if (r == &ioport_resource || r == &iomem_resource)
 			continue;
 		if (r && (r->flags & type_mask) == type && !r->parent)
@@ -301,7 +404,7 @@
 {
 	struct pci_dev *dev;
 	struct resource *b_res = find_free_bus_resource(bus, IORESOURCE_IO);
-	unsigned long size = 0, size1 = 0;
+	unsigned long size = 0, size1 = 0, old_size;
 
 	if (!b_res)
  		return;
@@ -326,12 +429,17 @@
 	}
 	if (size < min_size)
 		size = min_size;
+	old_size = resource_size(b_res);
+	if (old_size == 1)
+		old_size = 0;
 /* To be fixed in 2.5: we should have sort of HAVE_ISA
    flag in the struct pci_bus. */
 #if defined(CONFIG_ISA) || defined(CONFIG_EISA)
 	size = (size & 0xff) + ((size & ~0xffUL) << 2);
 #endif
 	size = ALIGN(size + size1, 4096);
+	if (size < old_size)
+		size = old_size;
 	if (!size) {
 		if (b_res->start || b_res->end)
 			dev_info(&bus->self->dev, "disabling bridge window "
@@ -352,7 +460,7 @@
 			 unsigned long type, resource_size_t min_size)
 {
 	struct pci_dev *dev;
-	resource_size_t min_align, align, size;
+	resource_size_t min_align, align, size, old_size;
 	resource_size_t aligns[12];	/* Alignments from 1Mb to 2Gb */
 	int order, max_order;
 	struct resource *b_res = find_free_bus_resource(bus, type);
@@ -402,6 +510,11 @@
 	}
 	if (size < min_size)
 		size = min_size;
+	old_size = resource_size(b_res);
+	if (old_size == 1)
+		old_size = 0;
+	if (size < old_size)
+		size = old_size;
 
 	align = 0;
 	min_align = 0;
@@ -538,23 +651,25 @@
 }
 EXPORT_SYMBOL(pci_bus_size_bridges);
 
-void __ref pci_bus_assign_resources(const struct pci_bus *bus)
+static void __ref __pci_bus_assign_resources(const struct pci_bus *bus,
+					 struct resource_list_x *fail_head)
 {
 	struct pci_bus *b;
 	struct pci_dev *dev;
 
-	pbus_assign_resources_sorted(bus);
+	pbus_assign_resources_sorted(bus, fail_head);
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		b = dev->subordinate;
 		if (!b)
 			continue;
 
-		pci_bus_assign_resources(b);
+		__pci_bus_assign_resources(b, fail_head);
 
 		switch (dev->class >> 8) {
 		case PCI_CLASS_BRIDGE_PCI:
-			pci_setup_bridge(b);
+			if (!pci_is_enabled(dev))
+				pci_setup_bridge(b);
 			break;
 
 		case PCI_CLASS_BRIDGE_CARDBUS:
@@ -568,15 +683,130 @@
 		}
 	}
 }
+
+void __ref pci_bus_assign_resources(const struct pci_bus *bus)
+{
+	__pci_bus_assign_resources(bus, NULL);
+}
 EXPORT_SYMBOL(pci_bus_assign_resources);
 
+static void __ref __pci_bridge_assign_resources(const struct pci_dev *bridge,
+					 struct resource_list_x *fail_head)
+{
+	struct pci_bus *b;
+
+	pdev_assign_resources_sorted((struct pci_dev *)bridge, fail_head);
+
+	b = bridge->subordinate;
+	if (!b)
+		return;
+
+	__pci_bus_assign_resources(b, fail_head);
+
+	switch (bridge->class >> 8) {
+	case PCI_CLASS_BRIDGE_PCI:
+		pci_setup_bridge(b);
+		break;
+
+	case PCI_CLASS_BRIDGE_CARDBUS:
+		pci_setup_cardbus(b);
+		break;
+
+	default:
+		dev_info(&bridge->dev, "not setting up bridge for bus "
+			 "%04x:%02x\n", pci_domain_nr(b), b->number);
+		break;
+	}
+}
+static void pci_bridge_release_resources(struct pci_bus *bus,
+					  unsigned long type)
+{
+	int idx;
+	bool changed = false;
+	struct pci_dev *dev;
+	struct resource *r;
+	unsigned long type_mask = IORESOURCE_IO | IORESOURCE_MEM |
+				  IORESOURCE_PREFETCH;
+
+	dev = bus->self;
+	for (idx = PCI_BRIDGE_RESOURCES; idx <= PCI_BRIDGE_RESOURCE_END;
+	     idx++) {
+		r = &dev->resource[idx];
+		if ((r->flags & type_mask) != type)
+			continue;
+		if (!r->parent)
+			continue;
+		/*
+		 * if there are children under that, we should release them
+		 *  all
+		 */
+		release_child_resources(r);
+		if (!release_resource(r)) {
+			dev_printk(KERN_DEBUG, &dev->dev,
+				 "resource %d %pR released\n", idx, r);
+			/* keep the old size */
+			r->end = resource_size(r) - 1;
+			r->start = 0;
+			r->flags = 0;
+			changed = true;
+		}
+	}
+
+	if (changed) {
+		/* avoiding touch the one without PREF */
+		if (type & IORESOURCE_PREFETCH)
+			type = IORESOURCE_PREFETCH;
+		__pci_setup_bridge(bus, type);
+	}
+}
+
+enum release_type {
+	leaf_only,
+	whole_subtree,
+};
+/*
+ * try to release pci bridge resources that is from leaf bridge,
+ * so we can allocate big new one later
+ */
+static void __ref pci_bus_release_bridge_resources(struct pci_bus *bus,
+						   unsigned long type,
+						   enum release_type rel_type)
+{
+	struct pci_dev *dev;
+	bool is_leaf_bridge = true;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		struct pci_bus *b = dev->subordinate;
+		if (!b)
+			continue;
+
+		is_leaf_bridge = false;
+
+		if ((dev->class >> 8) != PCI_CLASS_BRIDGE_PCI)
+			continue;
+
+		if (rel_type == whole_subtree)
+			pci_bus_release_bridge_resources(b, type,
+						 whole_subtree);
+	}
+
+	if (pci_is_root_bus(bus))
+		return;
+
+	if ((bus->self->class >> 8) != PCI_CLASS_BRIDGE_PCI)
+		return;
+
+	if ((rel_type == whole_subtree) || is_leaf_bridge)
+		pci_bridge_release_resources(bus, type);
+}
+
 static void pci_bus_dump_res(struct pci_bus *bus)
 {
-        int i;
+	struct resource *res;
+	int i;
 
-        for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-                struct resource *res = bus->resource[i];
-                if (!res || !res->end)
+	pci_bus_for_each_resource(bus, res, i) {
+		if (!res || !res->end || !res->flags)
                         continue;
 
 		dev_printk(KERN_DEBUG, &bus->dev, "resource %d %pR\n", i, res);
@@ -600,11 +830,65 @@
 	}
 }
 
+static int __init pci_bus_get_depth(struct pci_bus *bus)
+{
+	int depth = 0;
+	struct pci_dev *dev;
+
+	list_for_each_entry(dev, &bus->devices, bus_list) {
+		int ret;
+		struct pci_bus *b = dev->subordinate;
+		if (!b)
+			continue;
+
+		ret = pci_bus_get_depth(b);
+		if (ret + 1 > depth)
+			depth = ret + 1;
+	}
+
+	return depth;
+}
+static int __init pci_get_max_depth(void)
+{
+	int depth = 0;
+	struct pci_bus *bus;
+
+	list_for_each_entry(bus, &pci_root_buses, node) {
+		int ret;
+
+		ret = pci_bus_get_depth(bus);
+		if (ret > depth)
+			depth = ret;
+	}
+
+	return depth;
+}
+
+/*
+ * first try will not touch pci bridge res
+ * second  and later try will clear small leaf bridge res
+ * will stop till to the max  deepth if can not find good one
+ */
 void __init
 pci_assign_unassigned_resources(void)
 {
 	struct pci_bus *bus;
+	int tried_times = 0;
+	enum release_type rel_type = leaf_only;
+	struct resource_list_x head, *list;
+	unsigned long type_mask = IORESOURCE_IO | IORESOURCE_MEM |
+				  IORESOURCE_PREFETCH;
+	unsigned long failed_type;
+	int max_depth = pci_get_max_depth();
+	int pci_try_num;
 
+	head.next = NULL;
+
+	pci_try_num = max_depth + 1;
+	printk(KERN_DEBUG "PCI: max bus depth: %d pci_try_num: %d\n",
+		 max_depth, pci_try_num);
+
+again:
 	/* Depth first, calculate sizes and alignments of all
 	   subordinate buses. */
 	list_for_each_entry(bus, &pci_root_buses, node) {
@@ -612,12 +896,130 @@
 	}
 	/* Depth last, allocate resources and update the hardware. */
 	list_for_each_entry(bus, &pci_root_buses, node) {
-		pci_bus_assign_resources(bus);
-		pci_enable_bridges(bus);
+		__pci_bus_assign_resources(bus, &head);
 	}
+	tried_times++;
+
+	/* any device complain? */
+	if (!head.next)
+		goto enable_and_dump;
+	failed_type = 0;
+	for (list = head.next; list;) {
+		failed_type |= list->flags;
+		list = list->next;
+	}
+	/*
+	 * io port are tight, don't try extra
+	 * or if reach the limit, don't want to try more
+	 */
+	failed_type &= type_mask;
+	if ((failed_type == IORESOURCE_IO) || (tried_times >= pci_try_num)) {
+		free_failed_list(&head);
+		goto enable_and_dump;
+	}
+
+	printk(KERN_DEBUG "PCI: No. %d try to assign unassigned res\n",
+			 tried_times + 1);
+
+	/* third times and later will not check if it is leaf */
+	if ((tried_times + 1) > 2)
+		rel_type = whole_subtree;
+
+	/*
+	 * Try to release leaf bridge's resources that doesn't fit resource of
+	 * child device under that bridge
+	 */
+	for (list = head.next; list;) {
+		bus = list->dev->bus;
+		pci_bus_release_bridge_resources(bus, list->flags & type_mask,
+						  rel_type);
+		list = list->next;
+	}
+	/* restore size and flags */
+	for (list = head.next; list;) {
+		struct resource *res = list->res;
+
+		res->start = list->start;
+		res->end = list->end;
+		res->flags = list->flags;
+		if (list->dev->subordinate)
+			res->flags = 0;
+
+		list = list->next;
+	}
+	free_failed_list(&head);
+
+	goto again;
+
+enable_and_dump:
+	/* Depth last, update the hardware. */
+	list_for_each_entry(bus, &pci_root_buses, node)
+		pci_enable_bridges(bus);
 
 	/* dump the resource on buses */
 	list_for_each_entry(bus, &pci_root_buses, node) {
 		pci_bus_dump_resources(bus);
 	}
 }
+
+void pci_assign_unassigned_bridge_resources(struct pci_dev *bridge)
+{
+	struct pci_bus *parent = bridge->subordinate;
+	int tried_times = 0;
+	struct resource_list_x head, *list;
+	int retval;
+	unsigned long type_mask = IORESOURCE_IO | IORESOURCE_MEM |
+				  IORESOURCE_PREFETCH;
+
+	head.next = NULL;
+
+again:
+	pci_bus_size_bridges(parent);
+	__pci_bridge_assign_resources(bridge, &head);
+	retval = pci_reenable_device(bridge);
+	pci_set_master(bridge);
+	pci_enable_bridges(parent);
+
+	tried_times++;
+
+	if (!head.next)
+		return;
+
+	if (tried_times >= 2) {
+		/* still fail, don't need to try more */
+		free_failed_list(&head);
+		return;
+	}
+
+	printk(KERN_DEBUG "PCI: No. %d try to assign unassigned res\n",
+			 tried_times + 1);
+
+	/*
+	 * Try to release leaf bridge's resources that doesn't fit resource of
+	 * child device under that bridge
+	 */
+	for (list = head.next; list;) {
+		struct pci_bus *bus = list->dev->bus;
+		unsigned long flags = list->flags;
+
+		pci_bus_release_bridge_resources(bus, flags & type_mask,
+						 whole_subtree);
+		list = list->next;
+	}
+	/* restore size and flags */
+	for (list = head.next; list;) {
+		struct resource *res = list->res;
+
+		res->start = list->start;
+		res->end = list->end;
+		res->flags = list->flags;
+		if (list->dev->subordinate)
+			res->flags = 0;
+
+		list = list->next;
+	}
+	free_failed_list(&head);
+
+	goto again;
+}
+EXPORT_SYMBOL_GPL(pci_assign_unassigned_bridge_resources);
diff --git a/drivers/pci/slot.c b/drivers/pci/slot.c
index 8c02b6c..49c9e6c 100644
--- a/drivers/pci/slot.c
+++ b/drivers/pci/slot.c
@@ -47,6 +47,55 @@
 				slot->number);
 }
 
+/* these strings match up with the values in pci_bus_speed */
+static char *pci_bus_speed_strings[] = {
+	"33 MHz PCI",		/* 0x00 */
+	"66 MHz PCI",		/* 0x01 */
+	"66 MHz PCI-X", 	/* 0x02 */
+	"100 MHz PCI-X",	/* 0x03 */
+	"133 MHz PCI-X",	/* 0x04 */
+	NULL,			/* 0x05 */
+	NULL,			/* 0x06 */
+	NULL,			/* 0x07 */
+	NULL,			/* 0x08 */
+	"66 MHz PCI-X 266",	/* 0x09 */
+	"100 MHz PCI-X 266",	/* 0x0a */
+	"133 MHz PCI-X 266",	/* 0x0b */
+	"Unknown AGP",		/* 0x0c */
+	"1x AGP",		/* 0x0d */
+	"2x AGP",		/* 0x0e */
+	"4x AGP",		/* 0x0f */
+	"8x AGP",		/* 0x10 */
+	"66 MHz PCI-X 533",	/* 0x11 */
+	"100 MHz PCI-X 533",	/* 0x12 */
+	"133 MHz PCI-X 533",	/* 0x13 */
+	"2.5 GT/s PCIe",	/* 0x14 */
+	"5.0 GT/s PCIe",	/* 0x15 */
+	"8.0 GT/s PCIe",	/* 0x16 */
+};
+
+static ssize_t bus_speed_read(enum pci_bus_speed speed, char *buf)
+{
+	const char *speed_string;
+
+	if (speed < ARRAY_SIZE(pci_bus_speed_strings))
+		speed_string = pci_bus_speed_strings[speed];
+	else
+		speed_string = "Unknown";
+
+	return sprintf(buf, "%s\n", speed_string);
+}
+
+static ssize_t max_speed_read_file(struct pci_slot *slot, char *buf)
+{
+	return bus_speed_read(slot->bus->max_bus_speed, buf);
+}
+
+static ssize_t cur_speed_read_file(struct pci_slot *slot, char *buf)
+{
+	return bus_speed_read(slot->bus->cur_bus_speed, buf);
+}
+
 static void pci_slot_release(struct kobject *kobj)
 {
 	struct pci_dev *dev;
@@ -66,9 +115,15 @@
 
 static struct pci_slot_attribute pci_slot_attr_address =
 	__ATTR(address, (S_IFREG | S_IRUGO), address_read_file, NULL);
+static struct pci_slot_attribute pci_slot_attr_max_speed =
+	__ATTR(max_bus_speed, (S_IFREG | S_IRUGO), max_speed_read_file, NULL);
+static struct pci_slot_attribute pci_slot_attr_cur_speed =
+	__ATTR(cur_bus_speed, (S_IFREG | S_IRUGO), cur_speed_read_file, NULL);
 
 static struct attribute *pci_slot_default_attrs[] = {
 	&pci_slot_attr_address.attr,
+	&pci_slot_attr_max_speed.attr,
+	&pci_slot_attr_cur_speed.attr,
 	NULL,
 };
 
diff --git a/drivers/pcmcia/rsrc_mgr.c b/drivers/pcmcia/rsrc_mgr.c
index 52db172..f8401a0 100644
--- a/drivers/pcmcia/rsrc_mgr.c
+++ b/drivers/pcmcia/rsrc_mgr.c
@@ -114,22 +114,21 @@
 	unsigned long	offset;
 };
 
-static void pcmcia_align(void *align_data, struct resource *res,
-			unsigned long size, unsigned long align)
+static resource_size_t pcmcia_align(void *align_data,
+				const struct resource *res,
+				resource_size_t size, resource_size_t align)
 {
 	struct pcmcia_align_data *data = align_data;
-	unsigned long start;
+	resource_size_t start;
 
 	start = (res->start & ~data->mask) + data->offset;
 	if (start < res->start)
 		start += data->mask + 1;
-	res->start = start;
 
 #ifdef CONFIG_X86
 	if (res->flags & IORESOURCE_IO) {
 		if (start & 0x300) {
 			start = (start + 0x3ff) & ~0x3ff;
-			res->start = start;
 		}
 	}
 #endif
@@ -137,9 +136,11 @@
 #ifdef CONFIG_M68K
 	if (res->flags & IORESOURCE_IO) {
 		if ((res->start + size - 1) >= 1024)
-			res->start = res->end;
+			start = res->end;
 	}
 #endif
+
+	return start;
 }
 
 
diff --git a/drivers/pcmcia/rsrc_nonstatic.c b/drivers/pcmcia/rsrc_nonstatic.c
index 9b0dc43..c67638f 100644
--- a/drivers/pcmcia/rsrc_nonstatic.c
+++ b/drivers/pcmcia/rsrc_nonstatic.c
@@ -533,8 +533,8 @@
 	struct resource_map	*map;
 };
 
-static void
-pcmcia_common_align(void *align_data, struct resource *res,
+static resource_size_t
+pcmcia_common_align(void *align_data, const struct resource *res,
 			resource_size_t size, resource_size_t align)
 {
 	struct pcmcia_align_data *data = align_data;
@@ -545,17 +545,18 @@
 	start = (res->start & ~data->mask) + data->offset;
 	if (start < res->start)
 		start += data->mask + 1;
-	res->start = start;
+	return start;
 }
 
-static void
-pcmcia_align(void *align_data, struct resource *res, resource_size_t size,
-		resource_size_t align)
+static resource_size_t
+pcmcia_align(void *align_data, const struct resource *res,
+	resource_size_t size, resource_size_t align)
 {
 	struct pcmcia_align_data *data = align_data;
 	struct resource_map *m;
+	resource_size_t start;
 
-	pcmcia_common_align(data, res, size, align);
+	start = pcmcia_common_align(data, res, size, align);
 
 	for (m = data->map->next; m != data->map; m = m->next) {
 		unsigned long start = m->base;
@@ -567,8 +568,7 @@
 		 * fit here.
 		 */
 		if (res->start < start) {
-			res->start = start;
-			pcmcia_common_align(data, res, size, align);
+			start = pcmcia_common_align(data, res, size, align);
 		}
 
 		/*
@@ -586,7 +586,9 @@
 	 * If we failed to find something suitable, ensure we fail.
 	 */
 	if (m == data->map)
-		res->start = res->end;
+		start = res->end;
+
+	return start;
 }
 
 /*
@@ -801,8 +803,7 @@
 		return -EINVAL;
 #endif
 
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		res = s->cb_dev->bus->resource[i];
+	pci_bus_for_each_resource(s->cb_dev->bus, res, i) {
 		if (!res)
 			continue;
 
diff --git a/drivers/pcmcia/yenta_socket.c b/drivers/pcmcia/yenta_socket.c
index e4d12ac..1f2039d 100644
--- a/drivers/pcmcia/yenta_socket.c
+++ b/drivers/pcmcia/yenta_socket.c
@@ -649,9 +649,10 @@
 static int yenta_search_res(struct yenta_socket *socket, struct resource *res,
 			    u32 min)
 {
+	struct resource *root;
 	int i;
-	for (i = 0; i < PCI_BUS_NUM_RESOURCES; i++) {
-		struct resource *root = socket->dev->bus->resource[i];
+
+	pci_bus_for_each_resource(socket->dev->bus, root, i) {
 		if (!root)
 			continue;
 
diff --git a/include/acpi/acpi_bus.h b/include/acpi/acpi_bus.h
index 3cd9ccd..54508cc 100644
--- a/include/acpi/acpi_bus.h
+++ b/include/acpi/acpi_bus.h
@@ -242,6 +242,8 @@
 struct acpi_device_wakeup_flags {
 	u8 valid:1;		/* Can successfully enable wakeup? */
 	u8 run_wake:1;		/* Run-Wake GPE devices */
+	u8 always_enabled:1;	/* Run-wake devices that are always enabled */
+	u8 notifier_present:1;  /* Wake-up notify handler has been installed */
 };
 
 struct acpi_device_wakeup_state {
@@ -256,6 +258,7 @@
 	struct acpi_device_wakeup_state state;
 	struct acpi_device_wakeup_flags flags;
 	int prepare_count;
+	int run_wake_count;
 };
 
 /* Device */
@@ -386,6 +389,9 @@
 struct acpi_pci_root *acpi_pci_find_root(acpi_handle handle);
 #define DEVICE_ACPI_HANDLE(dev) ((acpi_handle)((dev)->archdata.acpi_handle))
 
+int acpi_enable_wakeup_device_power(struct acpi_device *dev, int state);
+int acpi_disable_wakeup_device_power(struct acpi_device *dev);
+
 #ifdef CONFIG_PM_SLEEP
 int acpi_pm_device_sleep_state(struct device *, int *);
 int acpi_pm_device_sleep_wake(struct device *, bool);
diff --git a/include/acpi/acpi_drivers.h b/include/acpi/acpi_drivers.h
index f4906f6..3a4767c 100644
--- a/include/acpi/acpi_drivers.h
+++ b/include/acpi/acpi_drivers.h
@@ -104,6 +104,7 @@
 
 struct pci_bus *pci_acpi_scan_root(struct acpi_device *device, int domain,
 				   int bus);
+void pci_acpi_crs_quirks(void);
 
 /* --------------------------------------------------------------------------
                                     Processor
diff --git a/include/acpi/acpixf.h b/include/acpi/acpixf.h
index 86e9735..3988f93 100644
--- a/include/acpi/acpixf.h
+++ b/include/acpi/acpixf.h
@@ -281,11 +281,11 @@
 /*
  * GPE Interfaces
  */
-acpi_status acpi_set_gpe_type(acpi_handle gpe_device, u32 gpe_number, u8 type);
+acpi_status acpi_set_gpe(acpi_handle gpe_device, u32 gpe_number, u8 action);
 
-acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number);
+acpi_status acpi_enable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type);
 
-acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number);
+acpi_status acpi_disable_gpe(acpi_handle gpe_device, u32 gpe_number, u8 type);
 
 acpi_status acpi_clear_gpe(acpi_handle gpe_device, u32 gpe_number, u32 flags);
 
diff --git a/include/acpi/actypes.h b/include/acpi/actypes.h
index 153f12d..73af408 100644
--- a/include/acpi/actypes.h
+++ b/include/acpi/actypes.h
@@ -668,15 +668,16 @@
 
 /*
  * GPE info flags - Per GPE
- * +-+-+-+---+---+-+
- * |7|6|5|4:3|2:1|0|
- * +-+-+-+---+---+-+
- *  | | |  |   |  |
- *  | | |  |   |  +--- Interrupt type: Edge or Level Triggered
- *  | | |  |   +--- Type: Wake-only, Runtime-only, or wake/runtime
+ * +-+-+-+---+-+-+-+
+ * |7|6|5|4:3|2|1|0|
+ * +-+-+-+---+-+-+-+
+ *  | | |  |  | | |
+ *  | | |  |  | | +--- Interrupt type: Edge or Level Triggered
+ *  | | |  |  | +--- GPE can wake the system
+ *  | | |  |  +--- Unused
  *  | | |  +--- Type of dispatch -- to method, handler, or none
- *  | | +--- Enabled for runtime?
- *  | +--- Enabled for wake?
+ *  | | +--- Unused
+ *  | +--- Unused
  *  +--- Unused
  */
 #define ACPI_GPE_XRUPT_TYPE_MASK        (u8) 0x01
@@ -687,22 +688,13 @@
 #define ACPI_GPE_TYPE_WAKE_RUN          (u8) 0x06
 #define ACPI_GPE_TYPE_WAKE              (u8) 0x02
 #define ACPI_GPE_TYPE_RUNTIME           (u8) 0x04	/* Default */
+#define ACPI_GPE_CAN_WAKE		(u8) 0x02
 
 #define ACPI_GPE_DISPATCH_MASK          (u8) 0x18
 #define ACPI_GPE_DISPATCH_HANDLER       (u8) 0x08
 #define ACPI_GPE_DISPATCH_METHOD        (u8) 0x10
 #define ACPI_GPE_DISPATCH_NOT_USED      (u8) 0x00	/* Default */
 
-#define ACPI_GPE_RUN_ENABLE_MASK        (u8) 0x20
-#define ACPI_GPE_RUN_ENABLED            (u8) 0x20
-#define ACPI_GPE_RUN_DISABLED           (u8) 0x00	/* Default */
-
-#define ACPI_GPE_WAKE_ENABLE_MASK       (u8) 0x40
-#define ACPI_GPE_WAKE_ENABLED           (u8) 0x40
-#define ACPI_GPE_WAKE_DISABLED          (u8) 0x00	/* Default */
-
-#define ACPI_GPE_ENABLE_MASK            (u8) 0x60	/* Both run/wake */
-
 /*
  * Flags for GPE and Lock interfaces
  */
diff --git a/include/linux/ioport.h b/include/linux/ioport.h
index 7129504..dda9841 100644
--- a/include/linux/ioport.h
+++ b/include/linux/ioport.h
@@ -112,6 +112,7 @@
 
 extern int request_resource(struct resource *root, struct resource *new);
 extern int release_resource(struct resource *new);
+void release_child_resources(struct resource *new);
 extern void reserve_region_with_split(struct resource *root,
 			     resource_size_t start, resource_size_t end,
 			     const char *name);
@@ -120,8 +121,10 @@
 extern int allocate_resource(struct resource *root, struct resource *new,
 			     resource_size_t size, resource_size_t min,
 			     resource_size_t max, resource_size_t align,
-			     void (*alignf)(void *, struct resource *,
-					    resource_size_t, resource_size_t),
+			     resource_size_t (*alignf)(void *,
+						       const struct resource *,
+						       resource_size_t,
+						       resource_size_t),
 			     void *alignf_data);
 int adjust_resource(struct resource *res, resource_size_t start,
 		    resource_size_t size);
diff --git a/include/linux/pci-acpi.h b/include/linux/pci-acpi.h
index 93a7c08f..c8b6473 100644
--- a/include/linux/pci-acpi.h
+++ b/include/linux/pci-acpi.h
@@ -11,6 +11,13 @@
 #include <linux/acpi.h>
 
 #ifdef CONFIG_ACPI
+extern acpi_status pci_acpi_add_bus_pm_notifier(struct acpi_device *dev,
+						 struct pci_bus *pci_bus);
+extern acpi_status pci_acpi_remove_bus_pm_notifier(struct acpi_device *dev);
+extern acpi_status pci_acpi_add_pm_notifier(struct acpi_device *dev,
+					     struct pci_dev *pci_dev);
+extern acpi_status pci_acpi_remove_pm_notifier(struct acpi_device *dev);
+
 static inline acpi_handle acpi_find_root_bridge_handle(struct pci_dev *pdev)
 {
 	struct pci_bus *pbus = pdev->bus;
diff --git a/include/linux/pci.h b/include/linux/pci.h
index c1968f4..e19a696 100644
--- a/include/linux/pci.h
+++ b/include/linux/pci.h
@@ -187,6 +187,33 @@
 	PCI_BUS_FLAGS_NO_MMRBC = (__force pci_bus_flags_t) 2,
 };
 
+/* Based on the PCI Hotplug Spec, but some values are made up by us */
+enum pci_bus_speed {
+	PCI_SPEED_33MHz			= 0x00,
+	PCI_SPEED_66MHz			= 0x01,
+	PCI_SPEED_66MHz_PCIX		= 0x02,
+	PCI_SPEED_100MHz_PCIX		= 0x03,
+	PCI_SPEED_133MHz_PCIX		= 0x04,
+	PCI_SPEED_66MHz_PCIX_ECC	= 0x05,
+	PCI_SPEED_100MHz_PCIX_ECC	= 0x06,
+	PCI_SPEED_133MHz_PCIX_ECC	= 0x07,
+	PCI_SPEED_66MHz_PCIX_266	= 0x09,
+	PCI_SPEED_100MHz_PCIX_266	= 0x0a,
+	PCI_SPEED_133MHz_PCIX_266	= 0x0b,
+	AGP_UNKNOWN			= 0x0c,
+	AGP_1X				= 0x0d,
+	AGP_2X				= 0x0e,
+	AGP_4X				= 0x0f,
+	AGP_8X				= 0x10,
+	PCI_SPEED_66MHz_PCIX_533	= 0x11,
+	PCI_SPEED_100MHz_PCIX_533	= 0x12,
+	PCI_SPEED_133MHz_PCIX_533	= 0x13,
+	PCIE_SPEED_2_5GT		= 0x14,
+	PCIE_SPEED_5_0GT		= 0x15,
+	PCIE_SPEED_8_0GT		= 0x16,
+	PCI_SPEED_UNKNOWN		= 0xff,
+};
+
 struct pci_cap_saved_state {
 	struct hlist_node next;
 	char cap_nr;
@@ -239,6 +266,7 @@
 					   configuration space */
 	unsigned int	pme_support:5;	/* Bitmask of states from which PME#
 					   can be generated */
+	unsigned int	pme_interrupt:1;
 	unsigned int	d1_support:1;	/* Low power state D1 is supported */
 	unsigned int	d2_support:1;	/* Low power state D2 is supported */
 	unsigned int	no_d1d2:1;	/* Only allow D0 and D3 */
@@ -275,7 +303,8 @@
 	unsigned int	msix_enabled:1;
 	unsigned int	ari_enabled:1;	/* ARI forwarding */
 	unsigned int	is_managed:1;
-	unsigned int	is_pcie:1;
+	unsigned int	is_pcie:1;	/* Obsolete. Will be removed.
+					   Use pci_is_pcie() instead */
 	unsigned int    needs_freset:1; /* Dev requires fundamental reset */
 	unsigned int	state_saved:1;
 	unsigned int	is_physfn:1;
@@ -335,9 +364,26 @@
 	hlist_add_head(&new_cap->next, &pci_dev->saved_cap_space);
 }
 
-#ifndef PCI_BUS_NUM_RESOURCES
-#define PCI_BUS_NUM_RESOURCES	16
-#endif
+/*
+ * The first PCI_BRIDGE_RESOURCE_NUM PCI bus resources (those that correspond
+ * to P2P or CardBus bridge windows) go in a table.  Additional ones (for
+ * buses below host bridges or subtractive decode bridges) go in the list.
+ * Use pci_bus_for_each_resource() to iterate through all the resources.
+ */
+
+/*
+ * PCI_SUBTRACTIVE_DECODE means the bridge forwards the window implicitly
+ * and there's no way to program the bridge with the details of the window.
+ * This does not apply to ACPI _CRS windows, even with the _DEC subtractive-
+ * decode bit set, because they are explicit and can be programmed with _SRS.
+ */
+#define PCI_SUBTRACTIVE_DECODE	0x1
+
+struct pci_bus_resource {
+	struct list_head list;
+	struct resource *res;
+	unsigned int flags;
+};
 
 #define PCI_REGION_FLAG_MASK	0x0fU	/* These bits of resource flags tell us the PCI region flags */
 
@@ -348,8 +394,8 @@
 	struct list_head devices;	/* list of devices on this bus */
 	struct pci_dev	*self;		/* bridge device as seen by parent */
 	struct list_head slots;		/* list of slots on this bus */
-	struct resource	*resource[PCI_BUS_NUM_RESOURCES];
-					/* address space routed to this bus */
+	struct resource *resource[PCI_BRIDGE_RESOURCE_NUM];
+	struct list_head resources;	/* address space routed to this bus */
 
 	struct pci_ops	*ops;		/* configuration access functions */
 	void		*sysdata;	/* hook for sys-specific extension */
@@ -359,6 +405,8 @@
 	unsigned char	primary;	/* number of primary bridge */
 	unsigned char	secondary;	/* number of secondary bridge */
 	unsigned char	subordinate;	/* max number of subordinate buses */
+	unsigned char	max_bus_speed;	/* enum pci_bus_speed */
+	unsigned char	cur_bus_speed;	/* enum pci_bus_speed */
 
 	char		name[48];
 
@@ -563,7 +611,8 @@
 char *pcibios_setup(char *str);
 
 /* Used only when drivers/pci/setup.c is used */
-void pcibios_align_resource(void *, struct resource *, resource_size_t,
+resource_size_t pcibios_align_resource(void *, const struct resource *,
+				resource_size_t,
 				resource_size_t);
 void pcibios_update_irq(struct pci_dev *, int irq);
 
@@ -589,6 +638,7 @@
 			       struct pci_ops *ops, void *sysdata);
 struct pci_bus *pci_add_new_bus(struct pci_bus *parent, struct pci_dev *dev,
 				int busnr);
+void pcie_update_link_speed(struct pci_bus *bus, u16 link_status);
 struct pci_slot *pci_create_slot(struct pci_bus *parent, int slot_nr,
 				 const char *name,
 				 struct hotplug_slot *hotplug);
@@ -615,12 +665,6 @@
 
 /* Generic PCI functions exported to card drivers */
 
-#ifdef CONFIG_PCI_LEGACY
-struct pci_dev __deprecated *pci_find_device(unsigned int vendor,
-					     unsigned int device,
-					     struct pci_dev *from);
-#endif /* CONFIG_PCI_LEGACY */
-
 enum pci_lost_interrupt_reason {
 	PCI_LOST_IRQ_NO_INFORMATION = 0,
 	PCI_LOST_IRQ_DISABLE_MSI,
@@ -750,11 +794,19 @@
 pci_power_t pci_choose_state(struct pci_dev *dev, pm_message_t state);
 bool pci_pme_capable(struct pci_dev *dev, pci_power_t state);
 void pci_pme_active(struct pci_dev *dev, bool enable);
-int pci_enable_wake(struct pci_dev *dev, pci_power_t state, bool enable);
+int __pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+		      bool runtime, bool enable);
 int pci_wake_from_d3(struct pci_dev *dev, bool enable);
 pci_power_t pci_target_state(struct pci_dev *dev);
 int pci_prepare_to_sleep(struct pci_dev *dev);
 int pci_back_from_sleep(struct pci_dev *dev);
+bool pci_dev_run_wake(struct pci_dev *dev);
+
+static inline int pci_enable_wake(struct pci_dev *dev, pci_power_t state,
+				  bool enable)
+{
+	return __pci_enable_wake(dev, state, false, enable);
+}
 
 /* For use by arch with custom probe code */
 void set_pcie_port_type(struct pci_dev *pdev);
@@ -776,6 +828,7 @@
 void pci_bus_size_bridges(struct pci_bus *bus);
 int pci_claim_resource(struct pci_dev *, int);
 void pci_assign_unassigned_resources(void);
+void pci_assign_unassigned_bridge_resources(struct pci_dev *bridge);
 void pdev_enable_device(struct pci_dev *);
 void pdev_sort_resources(struct pci_dev *, struct resource_list *);
 int pci_enable_resources(struct pci_dev *, int mask);
@@ -793,12 +846,23 @@
 void pci_release_selected_regions(struct pci_dev *, int);
 
 /* drivers/pci/bus.c */
+void pci_bus_add_resource(struct pci_bus *bus, struct resource *res, unsigned int flags);
+struct resource *pci_bus_resource_n(const struct pci_bus *bus, int n);
+void pci_bus_remove_resources(struct pci_bus *bus);
+
+#define pci_bus_for_each_resource(bus, res, i)				\
+	for (i = 0;							\
+	    (res = pci_bus_resource_n(bus, i)) || i < PCI_BRIDGE_RESOURCE_NUM; \
+	     i++)
+
 int __must_check pci_bus_alloc_resource(struct pci_bus *bus,
 			struct resource *res, resource_size_t size,
 			resource_size_t align, resource_size_t min,
 			unsigned int type_mask,
-			void (*alignf)(void *, struct resource *,
-				resource_size_t, resource_size_t),
+			resource_size_t (*alignf)(void *,
+						  const struct resource *,
+						  resource_size_t,
+						  resource_size_t),
 			void *alignf_data);
 void pci_enable_bridges(struct pci_bus *bus);
 
@@ -977,13 +1041,6 @@
 _PCI_NOP_ALL(read, *)
 _PCI_NOP_ALL(write,)
 
-static inline struct pci_dev *pci_find_device(unsigned int vendor,
-					      unsigned int device,
-					      struct pci_dev *from)
-{
-	return NULL;
-}
-
 static inline struct pci_dev *pci_get_device(unsigned int vendor,
 					     unsigned int device,
 					     struct pci_dev *from)
@@ -1241,8 +1298,12 @@
 	DECLARE_PCI_FIXUP_SECTION(.pci_fixup_suspend,			\
 			suspend##vendor##device##hook, vendor, device, hook)
 
-
+#ifdef CONFIG_PCI_QUIRKS
 void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev);
+#else
+static inline void pci_fixup_device(enum pci_fixup_pass pass,
+				    struct pci_dev *dev) {}
+#endif
 
 void __iomem *pcim_iomap(struct pci_dev *pdev, int bar, unsigned long maxlen);
 void pcim_iounmap(struct pci_dev *pdev, void __iomem *addr);
diff --git a/include/linux/pci_hotplug.h b/include/linux/pci_hotplug.h
index 652ba79..5d09cba 100644
--- a/include/linux/pci_hotplug.h
+++ b/include/linux/pci_hotplug.h
@@ -28,26 +28,6 @@
 #ifndef _PCI_HOTPLUG_H
 #define _PCI_HOTPLUG_H
 
-
-/* These values come from the PCI Hotplug Spec */
-enum pci_bus_speed {
-	PCI_SPEED_33MHz			= 0x00,
-	PCI_SPEED_66MHz			= 0x01,
-	PCI_SPEED_66MHz_PCIX		= 0x02,
-	PCI_SPEED_100MHz_PCIX		= 0x03,
-	PCI_SPEED_133MHz_PCIX		= 0x04,
-	PCI_SPEED_66MHz_PCIX_ECC	= 0x05,
-	PCI_SPEED_100MHz_PCIX_ECC	= 0x06,
-	PCI_SPEED_133MHz_PCIX_ECC	= 0x07,
-	PCI_SPEED_66MHz_PCIX_266	= 0x09,
-	PCI_SPEED_100MHz_PCIX_266	= 0x0a,
-	PCI_SPEED_133MHz_PCIX_266	= 0x0b,
-	PCI_SPEED_66MHz_PCIX_533	= 0x11,
-	PCI_SPEED_100MHz_PCIX_533	= 0x12,
-	PCI_SPEED_133MHz_PCIX_533	= 0x13,
-	PCI_SPEED_UNKNOWN		= 0xff,
-};
-
 /* These values come from the PCI Express Spec */
 enum pcie_link_width {
 	PCIE_LNK_WIDTH_RESRV	= 0x00,
@@ -61,12 +41,6 @@
 	PCIE_LNK_WIDTH_UNKNOWN  = 0xFF,
 };
 
-enum pcie_link_speed {
-	PCIE_2_5GB		= 0x14,
-	PCIE_5_0GB		= 0x15,
-	PCIE_LNK_SPEED_UNKNOWN	= 0xFF,
-};
-
 /**
  * struct hotplug_slot_ops -the callbacks that the hotplug pci core can use
  * @owner: The module owner of this structure
@@ -89,12 +63,6 @@
  * @get_adapter_status: Called to get see if an adapter is present in the slot or not.
  *	If this field is NULL, the value passed in the struct hotplug_slot_info
  *	will be used when this value is requested by a user.
- * @get_max_bus_speed: Called to get the max bus speed for a slot.
- *	If this field is NULL, the value passed in the struct hotplug_slot_info
- *	will be used when this value is requested by a user.
- * @get_cur_bus_speed: Called to get the current bus speed for a slot.
- *	If this field is NULL, the value passed in the struct hotplug_slot_info
- *	will be used when this value is requested by a user.
  *
  * The table of function pointers that is passed to the hotplug pci core by a
  * hotplug pci driver.  These functions are called by the hotplug pci core when
@@ -112,17 +80,14 @@
 	int (*get_attention_status)	(struct hotplug_slot *slot, u8 *value);
 	int (*get_latch_status)		(struct hotplug_slot *slot, u8 *value);
 	int (*get_adapter_status)	(struct hotplug_slot *slot, u8 *value);
-	int (*get_max_bus_speed)	(struct hotplug_slot *slot, enum pci_bus_speed *value);
-	int (*get_cur_bus_speed)	(struct hotplug_slot *slot, enum pci_bus_speed *value);
 };
 
 /**
  * struct hotplug_slot_info - used to notify the hotplug pci core of the state of the slot
- * @power: if power is enabled or not (1/0)
+ * @power_status: if power is enabled or not (1/0)
  * @attention_status: if the attention light is enabled or not (1/0)
  * @latch_status: if the latch (if any) is open or closed (1/0)
- * @adapter_present: if there is a pci board present in the slot or not (1/0)
- * @address: (domain << 16 | bus << 8 | dev)
+ * @adapter_status: if there is a pci board present in the slot or not (1/0)
  *
  * Used to notify the hotplug pci core of the status of a specific slot.
  */
@@ -131,8 +96,6 @@
 	u8	attention_status;
 	u8	latch_status;
 	u8	adapter_status;
-	enum pci_bus_speed	max_bus_speed;
-	enum pci_bus_speed	cur_bus_speed;
 };
 
 /**
diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
index cca8a04..0be8243 100644
--- a/include/linux/pci_ids.h
+++ b/include/linux/pci_ids.h
@@ -2417,6 +2417,9 @@
 #define PCI_DEVICE_ID_INTEL_82840_HB	0x1a21
 #define PCI_DEVICE_ID_INTEL_82845_HB	0x1a30
 #define PCI_DEVICE_ID_INTEL_IOAT	0x1a38
+#define PCI_DEVICE_ID_INTEL_CPT_SMBUS	0x1c22
+#define PCI_DEVICE_ID_INTEL_CPT_LPC1	0x1c42
+#define PCI_DEVICE_ID_INTEL_CPT_LPC2	0x1c43
 #define PCI_DEVICE_ID_INTEL_82801AA_0	0x2410
 #define PCI_DEVICE_ID_INTEL_82801AA_1	0x2411
 #define PCI_DEVICE_ID_INTEL_82801AA_3	0x2413
diff --git a/kernel/power/Kconfig b/kernel/power/Kconfig
index 91e09d3..4c9cffc 100644
--- a/kernel/power/Kconfig
+++ b/kernel/power/Kconfig
@@ -222,3 +222,8 @@
 	  and the bus type drivers of the buses the devices are on are
 	  responsible for the actual handling of the autosuspend requests and
 	  wake-up events.
+
+config PM_OPS
+	bool
+	depends on PM_SLEEP || PM_RUNTIME
+	default y
diff --git a/kernel/resource.c b/kernel/resource.c
index af96c1e..24e9e60 100644
--- a/kernel/resource.c
+++ b/kernel/resource.c
@@ -188,6 +188,36 @@
 	return -EINVAL;
 }
 
+static void __release_child_resources(struct resource *r)
+{
+	struct resource *tmp, *p;
+	resource_size_t size;
+
+	p = r->child;
+	r->child = NULL;
+	while (p) {
+		tmp = p;
+		p = p->sibling;
+
+		tmp->parent = NULL;
+		tmp->sibling = NULL;
+		__release_child_resources(tmp);
+
+		printk(KERN_DEBUG "release child resource %pR\n", tmp);
+		/* need to restore size, and keep flags */
+		size = resource_size(tmp);
+		tmp->start = 0;
+		tmp->end = size - 1;
+	}
+}
+
+void release_child_resources(struct resource *r)
+{
+	write_lock(&resource_lock);
+	__release_child_resources(r);
+	write_unlock(&resource_lock);
+}
+
 /**
  * request_resource - request and reserve an I/O or memory resource
  * @root: root resource descriptor
@@ -303,8 +333,10 @@
 static int find_resource(struct resource *root, struct resource *new,
 			 resource_size_t size, resource_size_t min,
 			 resource_size_t max, resource_size_t align,
-			 void (*alignf)(void *, struct resource *,
-					resource_size_t, resource_size_t),
+			 resource_size_t (*alignf)(void *,
+						   const struct resource *,
+						   resource_size_t,
+						   resource_size_t),
 			 void *alignf_data)
 {
 	struct resource *this = root->child;
@@ -330,7 +362,7 @@
 			tmp.end = max;
 		tmp.start = ALIGN(tmp.start, align);
 		if (alignf)
-			alignf(alignf_data, &tmp, size, align);
+			tmp.start = alignf(alignf_data, &tmp, size, align);
 		if (tmp.start < tmp.end && tmp.end - tmp.start >= size - 1) {
 			new->start = tmp.start;
 			new->end = tmp.start + size - 1;
@@ -358,8 +390,10 @@
 int allocate_resource(struct resource *root, struct resource *new,
 		      resource_size_t size, resource_size_t min,
 		      resource_size_t max, resource_size_t align,
-		      void (*alignf)(void *, struct resource *,
-				     resource_size_t, resource_size_t),
+		      resource_size_t (*alignf)(void *,
+						const struct resource *,
+						resource_size_t,
+						resource_size_t),
 		      void *alignf_data)
 {
 	int err;