[libata] Add a bunch of PATA drivers.

The vast majority of drivers and changes are from Alan Cox.  Albert Lee
contributed and maintains pata_pdc2027x.  Adrian Bunk, Andrew Morton,
and Tejun Heo contributed various minor fixes and updates.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/pata_artop.c b/drivers/ata/pata_artop.c
new file mode 100644
index 0000000..d6ef3bf
--- /dev/null
+++ b/drivers/ata/pata_artop.c
@@ -0,0 +1,518 @@
+/*
+ *    pata_artop.c - ARTOP ATA controller driver
+ *
+ *	(C) 2006 Red Hat <alan@redhat.com>
+ *
+ *    Based in part on drivers/ide/pci/aec62xx.c
+ *	Copyright (C) 1999-2002	Andre Hedrick <andre@linux-ide.org>
+ *	865/865R fixes for Macintosh card version from a patch to the old
+ *		driver by Thibaut VARENE <varenet@parisc-linux.org>
+ *	When setting the PCI latency we must set 0x80 or higher for burst
+ *		performance Alessandro Zummo <alessandro.zummo@towertech.it>
+ *
+ *	TODO
+ *	850 serialization once the core supports it
+ *	Investigate no_dsc on 850R
+ *	Clock detect
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME	"pata_artop"
+#define DRV_VERSION	"0.4.1"
+
+/*
+ *	The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
+ *	get PCI bus speed functionality we leave this as 0. Its a variable
+ *	for when we get the functionality and also for folks wanting to
+ *	test stuff.
+ */
+
+static int clock = 0;
+
+static int artop6210_pre_reset(struct ata_port *ap)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	const struct pci_bits artop_enable_bits[] = {
+		{ 0x4AU, 1U, 0x02UL, 0x02UL },	/* port 0 */
+		{ 0x4AU, 1U, 0x04UL, 0x04UL },	/* port 1 */
+	};
+
+	if (!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+		ata_port_disable(ap);
+		printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+		return 0;
+	}
+	ap->cbl = ATA_CBL_PATA40;
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	artop6210_error_handler - Probe specified port on PATA host controller
+ *	@ap: Port to probe
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, artop6210_pre_reset,
+				    ata_std_softreset, NULL,
+				    ata_std_postreset);
+}
+
+/**
+ *	artop6260_pre_reset	-	check for 40/80 pin
+ *	@ap: Port
+ *
+ *	The ARTOP hardware reports the cable detect bits in register 0x49.
+ *	Nothing complicated needed here.
+ */
+
+static int artop6260_pre_reset(struct ata_port *ap)
+{
+	static const struct pci_bits artop_enable_bits[] = {
+		{ 0x4AU, 1U, 0x02UL, 0x02UL },	/* port 0 */
+		{ 0x4AU, 1U, 0x04UL, 0x04UL },	/* port 1 */
+	};
+
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u8 tmp;
+
+	/* Odd numbered device ids are the units with enable bits (the -R cards) */
+	if (pdev->device % 1 && !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no])) {
+		ata_port_disable(ap);
+		printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
+		return 0;
+	}
+	pci_read_config_byte(pdev, 0x49, &tmp);
+	if (tmp & (1 >> ap->port_no))
+		ap->cbl = ATA_CBL_PATA40;
+	else
+		ap->cbl = ATA_CBL_PATA80;
+	return ata_std_prereset(ap);
+}
+
+/**
+ *	artop6260_error_handler - Probe specified port on PATA host controller
+ *	@ap: Port to probe
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_error_handler(struct ata_port *ap)
+{
+	ata_bmdma_drive_eh(ap, artop6260_pre_reset,
+				    ata_std_softreset, NULL,
+				    ata_std_postreset);
+}
+
+/**
+ *	artop6210_load_piomode - Load a set of PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device
+ *	@pio: PIO mode
+ *
+ *	Set PIO mode for device, in host controller PCI config space. This
+ *	is used both to set PIO timings in PIO mode and also to set the
+ *	matching PIO clocking for UDMA, as well as the MWDMA timings.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	const u16 timing[2][5] = {
+		{ 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
+		{ 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }
+
+	};
+	/* Load the PIO timing active/recovery bits */
+	pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
+}
+
+/**
+ *	artop6210_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set PIO mode for device, in host controller PCI config space. For
+ *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *	the event UDMA is used the later call to set_dmamode will set the
+ *	bits as required.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	u8 ultra;
+
+	artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+	pci_read_config_byte(pdev, 0x54, &ultra);
+	ultra &= ~(3 << (2 * dn));
+	pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *	artop6260_load_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *	@pio: PIO mode
+ *
+ *	Set PIO mode for device, in host controller PCI config space. The
+ *	ARTOP6260 and relatives store the timing data differently.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	const u8 timing[2][5] = {
+		{ 0x00, 0x0A, 0x08, 0x33, 0x31 },
+		{ 0x70, 0x7A, 0x78, 0x43, 0x41 }
+
+	};
+	/* Load the PIO timing active/recovery bits */
+	pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
+}
+
+/**
+ *	artop6260_set_piomode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set PIO mode for device, in host controller PCI config space. For
+ *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
+ *	the event UDMA is used the later call to set_dmamode will set the
+ *	bits as required.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	u8 ultra;
+
+	artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);
+
+	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
+	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
+	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+/**
+ *	artop6210_set_dmamode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: um
+ *
+ *	Set DMA mode for device, in host controller PCI config space.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio;
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	int dn = adev->devno + 2 * ap->port_no;
+	u8 ultra;
+
+	if (adev->dma_mode == XFER_MW_DMA_0)
+		pio = 1;
+	else
+		pio = 4;
+
+	/* Load the PIO timing active/recovery bits */
+	artop6210_load_piomode(ap, adev, pio);
+
+	pci_read_config_byte(pdev, 0x54, &ultra);
+	ultra &= ~(3 << (2 * dn));
+
+	/* Add ultra DMA bits if in UDMA mode */
+	if (adev->dma_mode >= XFER_UDMA_0) {
+		u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
+		if (mode == 0)
+			mode = 1;
+		ultra |= (mode << (2 * dn));
+	}
+	pci_write_config_byte(pdev, 0x54, ultra);
+}
+
+/**
+ *	artop6260_set_dmamode - Initialize host controller PATA PIO timings
+ *	@ap: Port whose timings we are configuring
+ *	@adev: Device we are configuring
+ *
+ *	Set DMA mode for device, in host controller PCI config space. The
+ *	ARTOP6260 and relatives store the timing data differently.
+ *
+ *	LOCKING:
+ *	None (inherited from caller).
+ */
+
+static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
+	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
+	u8 ultra;
+
+	if (adev->dma_mode == XFER_MW_DMA_0)
+		pio = 1;
+	else
+		pio = 4;
+
+	/* Load the PIO timing active/recovery bits */
+	artop6260_load_piomode(ap, adev, pio);
+
+	/* Add ultra DMA bits if in UDMA mode */
+	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
+	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
+	if (adev->dma_mode >= XFER_UDMA_0) {
+		u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
+		if (mode == 0)
+			mode = 1;
+		ultra |= (mode << (4 * adev->devno));
+	}
+	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
+}
+
+static struct scsi_host_template artop_sht = {
+	.module			= THIS_MODULE,
+	.name			= DRV_NAME,
+	.ioctl			= ata_scsi_ioctl,
+	.queuecommand		= ata_scsi_queuecmd,
+	.can_queue		= ATA_DEF_QUEUE,
+	.this_id		= ATA_SHT_THIS_ID,
+	.sg_tablesize		= LIBATA_MAX_PRD,
+	.max_sectors		= ATA_MAX_SECTORS,
+	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
+	.emulated		= ATA_SHT_EMULATED,
+	.use_clustering		= ATA_SHT_USE_CLUSTERING,
+	.proc_name		= DRV_NAME,
+	.dma_boundary		= ATA_DMA_BOUNDARY,
+	.slave_configure	= ata_scsi_slave_config,
+	.bios_param		= ata_std_bios_param,
+};
+
+static const struct ata_port_operations artop6210_ops = {
+	.port_disable		= ata_port_disable,
+	.set_piomode		= artop6210_set_piomode,
+	.set_dmamode		= artop6210_set_dmamode,
+	.mode_filter		= ata_pci_default_filter,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= artop6210_error_handler,
+	.post_internal_cmd 	= ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+	.eng_timeout		= ata_eng_timeout,
+	.data_xfer		= ata_pio_data_xfer,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= ata_host_stop,
+};
+
+static const struct ata_port_operations artop6260_ops = {
+	.port_disable		= ata_port_disable,
+	.set_piomode		= artop6260_set_piomode,
+	.set_dmamode		= artop6260_set_dmamode,
+
+	.tf_load		= ata_tf_load,
+	.tf_read		= ata_tf_read,
+	.check_status		= ata_check_status,
+	.exec_command		= ata_exec_command,
+	.dev_select		= ata_std_dev_select,
+
+	.freeze			= ata_bmdma_freeze,
+	.thaw			= ata_bmdma_thaw,
+	.error_handler		= artop6260_error_handler,
+	.post_internal_cmd 	= ata_bmdma_post_internal_cmd,
+
+	.bmdma_setup		= ata_bmdma_setup,
+	.bmdma_start		= ata_bmdma_start,
+	.bmdma_stop		= ata_bmdma_stop,
+	.bmdma_status		= ata_bmdma_status,
+	.qc_prep		= ata_qc_prep,
+	.qc_issue		= ata_qc_issue_prot,
+	.data_xfer		= ata_pio_data_xfer,
+
+	.eng_timeout		= ata_eng_timeout,
+
+	.irq_handler		= ata_interrupt,
+	.irq_clear		= ata_bmdma_irq_clear,
+
+	.port_start		= ata_port_start,
+	.port_stop		= ata_port_stop,
+	.host_stop		= ata_host_stop,
+};
+
+
+/**
+ *	artop_init_one - Register ARTOP ATA PCI device with kernel services
+ *	@pdev: PCI device to register
+ *	@ent: Entry in artop_pci_tbl matching with @pdev
+ *
+ *	Called from kernel PCI layer.
+ *
+ *	LOCKING:
+ *	Inherited from PCI layer (may sleep).
+ *
+ *	RETURNS:
+ *	Zero on success, or -ERRNO value.
+ */
+
+static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static int printed_version;
+	static struct ata_port_info info_6210 = {
+		.sht		= &artop_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask 	= ATA_UDMA2,
+		.port_ops	= &artop6210_ops,
+	};
+	static struct ata_port_info info_626x = {
+		.sht		= &artop_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask 	= ATA_UDMA4,
+		.port_ops	= &artop6260_ops,
+	};
+	static struct ata_port_info info_626x_fast = {
+		.sht		= &artop_sht,
+		.flags		= ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
+		.pio_mask	= 0x1f,	/* pio0-4 */
+		.mwdma_mask	= 0x07, /* mwdma0-2 */
+		.udma_mask 	= ATA_UDMA5,
+		.port_ops	= &artop6260_ops,
+	};
+	struct ata_port_info *port_info[2];
+	struct ata_port_info *info;
+	int ports = 2;
+
+	if (!printed_version++)
+		dev_printk(KERN_DEBUG, &pdev->dev,
+			   "version " DRV_VERSION "\n");
+
+	if (id->driver_data == 0) {	/* 6210 variant */
+		info = &info_6210;
+		/* BIOS may have left us in UDMA, clear it before libata probe */
+		pci_write_config_byte(pdev, 0x54, 0);
+		/* For the moment (also lacks dsc) */
+		printk(KERN_WARNING "ARTOP 6210 requires serialize functionality not yet supported by libata.\n");
+		printk(KERN_WARNING "Secondary ATA ports will not be activated.\n");
+		ports = 1;
+	}
+	else if (id->driver_data == 1)	/* 6260 */
+		info = &info_626x;
+	else if (id->driver_data == 2)	{ /* 6260 or 6260 + fast */
+		unsigned long io = pci_resource_start(pdev, 4);
+		u8 reg;
+
+		info = &info_626x;
+		if (inb(io) & 0x10)
+			info = &info_626x_fast;
+		/* Mac systems come up with some registers not set as we
+		   will need them */
+
+		/* Clear reset & test bits */
+		pci_read_config_byte(pdev, 0x49, &reg);
+		pci_write_config_byte(pdev, 0x49, reg & ~ 0x30);
+
+		/* PCI latency must be > 0x80 for burst mode, tweak it
+		 * if required.
+		 */
+		pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
+		if (reg <= 0x80)
+			pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);
+
+		/* Enable IRQ output and burst mode */
+		pci_read_config_byte(pdev, 0x4a, &reg);
+		pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+
+	}
+	port_info[0] = port_info[1] = info;
+	return ata_pci_init_one(pdev, port_info, ports);
+}
+
+static const struct pci_device_id artop_pci_tbl[] = {
+	{ 0x1191, 0x0005, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{ 0x1191, 0x0006, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+	{ 0x1191, 0x0007, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+	{ 0x1191, 0x0008, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+	{ 0x1191, 0x0009, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+	{ }	/* terminate list */
+};
+
+static struct pci_driver artop_pci_driver = {
+	.name			= DRV_NAME,
+	.id_table		= artop_pci_tbl,
+	.probe			= artop_init_one,
+	.remove			= ata_pci_remove_one,
+};
+
+static int __init artop_init(void)
+{
+	return pci_register_driver(&artop_pci_driver);
+}
+
+static void __exit artop_exit(void)
+{
+	pci_unregister_driver(&artop_pci_driver);
+}
+
+
+module_init(artop_init);
+module_exit(artop_exit);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+