Merge master.kernel.org:/pub/scm/linux/kernel/git/gregkh/spi-2.6
diff --git a/Documentation/spi/butterfly b/Documentation/spi/butterfly
new file mode 100644
index 0000000..a2e8c8d
--- /dev/null
+++ b/Documentation/spi/butterfly
@@ -0,0 +1,57 @@
+spi_butterfly - parport-to-butterfly adapter driver
+===================================================
+
+This is a hardware and software project that includes building and using
+a parallel port adapter cable, together with an "AVR Butterfly" to run
+firmware for user interfacing and/or sensors. A Butterfly is a $US20
+battery powered card with an AVR microcontroller and lots of goodies:
+sensors, LCD, flash, toggle stick, and more. You can use AVR-GCC to
+develop firmware for this, and flash it using this adapter cable.
+
+You can make this adapter from an old printer cable and solder things
+directly to the Butterfly. Or (if you have the parts and skills) you
+can come up with something fancier, providing ciruit protection to the
+Butterfly and the printer port, or with a better power supply than two
+signal pins from the printer port.
+
+
+The first cable connections will hook Linux up to one SPI bus, with the
+AVR and a DataFlash chip; and to the AVR reset line. This is all you
+need to reflash the firmware, and the pins are the standard Atmel "ISP"
+connector pins (used also on non-Butterfly AVR boards).
+
+ Signal Butterfly Parport (DB-25)
+ ------ --------- ---------------
+ SCK = J403.PB1/SCK = pin 2/D0
+ RESET = J403.nRST = pin 3/D1
+ VCC = J403.VCC_EXT = pin 8/D6
+ MOSI = J403.PB2/MOSI = pin 9/D7
+ MISO = J403.PB3/MISO = pin 11/S7,nBUSY
+ GND = J403.GND = pin 23/GND
+
+Then to let Linux master that bus to talk to the DataFlash chip, you must
+(a) flash new firmware that disables SPI (set PRR.2, and disable pullups
+by clearing PORTB.[0-3]); (b) configure the mtd_dataflash driver; and
+(c) cable in the chipselect.
+
+ Signal Butterfly Parport (DB-25)
+ ------ --------- ---------------
+ VCC = J400.VCC_EXT = pin 7/D5
+ SELECT = J400.PB0/nSS = pin 17/C3,nSELECT
+ GND = J400.GND = pin 24/GND
+
+The "USI" controller, using J405, can be used for a second SPI bus. That
+would let you talk to the AVR over SPI, running firmware that makes it act
+as an SPI slave, while letting either Linux or the AVR use the DataFlash.
+There are plenty of spare parport pins to wire this one up, such as:
+
+ Signal Butterfly Parport (DB-25)
+ ------ --------- ---------------
+ SCK = J403.PE4/USCK = pin 5/D3
+ MOSI = J403.PE5/DI = pin 6/D4
+ MISO = J403.PE6/DO = pin 12/S5,nPAPEROUT
+ GND = J403.GND = pin 22/GND
+
+ IRQ = J402.PF4 = pin 10/S6,ACK
+ GND = J402.GND(P2) = pin 25/GND
+
diff --git a/Documentation/spi/spi-summary b/Documentation/spi/spi-summary
new file mode 100644
index 0000000..a5ffba3
--- /dev/null
+++ b/Documentation/spi/spi-summary
@@ -0,0 +1,457 @@
+Overview of Linux kernel SPI support
+====================================
+
+02-Dec-2005
+
+What is SPI?
+------------
+The "Serial Peripheral Interface" (SPI) is a synchronous four wire serial
+link used to connect microcontrollers to sensors, memory, and peripherals.
+
+The three signal wires hold a clock (SCLK, often on the order of 10 MHz),
+and parallel data lines with "Master Out, Slave In" (MOSI) or "Master In,
+Slave Out" (MISO) signals. (Other names are also used.) There are four
+clocking modes through which data is exchanged; mode-0 and mode-3 are most
+commonly used. Each clock cycle shifts data out and data in; the clock
+doesn't cycle except when there is data to shift.
+
+SPI masters may use a "chip select" line to activate a given SPI slave
+device, so those three signal wires may be connected to several chips
+in parallel. All SPI slaves support chipselects. Some devices have
+other signals, often including an interrupt to the master.
+
+Unlike serial busses like USB or SMBUS, even low level protocols for
+SPI slave functions are usually not interoperable between vendors
+(except for cases like SPI memory chips).
+
+ - SPI may be used for request/response style device protocols, as with
+ touchscreen sensors and memory chips.
+
+ - It may also be used to stream data in either direction (half duplex),
+ or both of them at the same time (full duplex).
+
+ - Some devices may use eight bit words. Others may different word
+ lengths, such as streams of 12-bit or 20-bit digital samples.
+
+In the same way, SPI slaves will only rarely support any kind of automatic
+discovery/enumeration protocol. The tree of slave devices accessible from
+a given SPI master will normally be set up manually, with configuration
+tables.
+
+SPI is only one of the names used by such four-wire protocols, and
+most controllers have no problem handling "MicroWire" (think of it as
+half-duplex SPI, for request/response protocols), SSP ("Synchronous
+Serial Protocol"), PSP ("Programmable Serial Protocol"), and other
+related protocols.
+
+Microcontrollers often support both master and slave sides of the SPI
+protocol. This document (and Linux) currently only supports the master
+side of SPI interactions.
+
+
+Who uses it? On what kinds of systems?
+---------------------------------------
+Linux developers using SPI are probably writing device drivers for embedded
+systems boards. SPI is used to control external chips, and it is also a
+protocol supported by every MMC or SD memory card. (The older "DataFlash"
+cards, predating MMC cards but using the same connectors and card shape,
+support only SPI.) Some PC hardware uses SPI flash for BIOS code.
+
+SPI slave chips range from digital/analog converters used for analog
+sensors and codecs, to memory, to peripherals like USB controllers
+or Ethernet adapters; and more.
+
+Most systems using SPI will integrate a few devices on a mainboard.
+Some provide SPI links on expansion connectors; in cases where no
+dedicated SPI controller exists, GPIO pins can be used to create a
+low speed "bitbanging" adapter. Very few systems will "hotplug" an SPI
+controller; the reasons to use SPI focus on low cost and simple operation,
+and if dynamic reconfiguration is important, USB will often be a more
+appropriate low-pincount peripheral bus.
+
+Many microcontrollers that can run Linux integrate one or more I/O
+interfaces with SPI modes. Given SPI support, they could use MMC or SD
+cards without needing a special purpose MMC/SD/SDIO controller.
+
+
+How do these driver programming interfaces work?
+------------------------------------------------
+The <linux/spi/spi.h> header file includes kerneldoc, as does the
+main source code, and you should certainly read that. This is just
+an overview, so you get the big picture before the details.
+
+SPI requests always go into I/O queues. Requests for a given SPI device
+are always executed in FIFO order, and complete asynchronously through
+completion callbacks. There are also some simple synchronous wrappers
+for those calls, including ones for common transaction types like writing
+a command and then reading its response.
+
+There are two types of SPI driver, here called:
+
+ Controller drivers ... these are often built in to System-On-Chip
+ processors, and often support both Master and Slave roles.
+ These drivers touch hardware registers and may use DMA.
+ Or they can be PIO bitbangers, needing just GPIO pins.
+
+ Protocol drivers ... these pass messages through the controller
+ driver to communicate with a Slave or Master device on the
+ other side of an SPI link.
+
+So for example one protocol driver might talk to the MTD layer to export
+data to filesystems stored on SPI flash like DataFlash; and others might
+control audio interfaces, present touchscreen sensors as input interfaces,
+or monitor temperature and voltage levels during industrial processing.
+And those might all be sharing the same controller driver.
+
+A "struct spi_device" encapsulates the master-side interface between
+those two types of driver. At this writing, Linux has no slave side
+programming interface.
+
+There is a minimal core of SPI programming interfaces, focussing on
+using driver model to connect controller and protocol drivers using
+device tables provided by board specific initialization code. SPI
+shows up in sysfs in several locations:
+
+ /sys/devices/.../CTLR/spiB.C ... spi_device for on bus "B",
+ chipselect C, accessed through CTLR.
+
+ /sys/devices/.../CTLR/spiB.C/modalias ... identifies the driver
+ that should be used with this device (for hotplug/coldplug)
+
+ /sys/bus/spi/devices/spiB.C ... symlink to the physical
+ spiB-C device
+
+ /sys/bus/spi/drivers/D ... driver for one or more spi*.* devices
+
+ /sys/class/spi_master/spiB ... class device for the controller
+ managing bus "B". All the spiB.* devices share the same
+ physical SPI bus segment, with SCLK, MOSI, and MISO.
+
+
+How does board-specific init code declare SPI devices?
+------------------------------------------------------
+Linux needs several kinds of information to properly configure SPI devices.
+That information is normally provided by board-specific code, even for
+chips that do support some of automated discovery/enumeration.
+
+DECLARE CONTROLLERS
+
+The first kind of information is a list of what SPI controllers exist.
+For System-on-Chip (SOC) based boards, these will usually be platform
+devices, and the controller may need some platform_data in order to
+operate properly. The "struct platform_device" will include resources
+like the physical address of the controller's first register and its IRQ.
+
+Platforms will often abstract the "register SPI controller" operation,
+maybe coupling it with code to initialize pin configurations, so that
+the arch/.../mach-*/board-*.c files for several boards can all share the
+same basic controller setup code. This is because most SOCs have several
+SPI-capable controllers, and only the ones actually usable on a given
+board should normally be set up and registered.
+
+So for example arch/.../mach-*/board-*.c files might have code like:
+
+ #include <asm/arch/spi.h> /* for mysoc_spi_data */
+
+ /* if your mach-* infrastructure doesn't support kernels that can
+ * run on multiple boards, pdata wouldn't benefit from "__init".
+ */
+ static struct mysoc_spi_data __init pdata = { ... };
+
+ static __init board_init(void)
+ {
+ ...
+ /* this board only uses SPI controller #2 */
+ mysoc_register_spi(2, &pdata);
+ ...
+ }
+
+And SOC-specific utility code might look something like:
+
+ #include <asm/arch/spi.h>
+
+ static struct platform_device spi2 = { ... };
+
+ void mysoc_register_spi(unsigned n, struct mysoc_spi_data *pdata)
+ {
+ struct mysoc_spi_data *pdata2;
+
+ pdata2 = kmalloc(sizeof *pdata2, GFP_KERNEL);
+ *pdata2 = pdata;
+ ...
+ if (n == 2) {
+ spi2->dev.platform_data = pdata2;
+ register_platform_device(&spi2);
+
+ /* also: set up pin modes so the spi2 signals are
+ * visible on the relevant pins ... bootloaders on
+ * production boards may already have done this, but
+ * developer boards will often need Linux to do it.
+ */
+ }
+ ...
+ }
+
+Notice how the platform_data for boards may be different, even if the
+same SOC controller is used. For example, on one board SPI might use
+an external clock, where another derives the SPI clock from current
+settings of some master clock.
+
+
+DECLARE SLAVE DEVICES
+
+The second kind of information is a list of what SPI slave devices exist
+on the target board, often with some board-specific data needed for the
+driver to work correctly.
+
+Normally your arch/.../mach-*/board-*.c files would provide a small table
+listing the SPI devices on each board. (This would typically be only a
+small handful.) That might look like:
+
+ static struct ads7846_platform_data ads_info = {
+ .vref_delay_usecs = 100,
+ .x_plate_ohms = 580,
+ .y_plate_ohms = 410,
+ };
+
+ static struct spi_board_info spi_board_info[] __initdata = {
+ {
+ .modalias = "ads7846",
+ .platform_data = &ads_info,
+ .mode = SPI_MODE_0,
+ .irq = GPIO_IRQ(31),
+ .max_speed_hz = 120000 /* max sample rate at 3V */ * 16,
+ .bus_num = 1,
+ .chip_select = 0,
+ },
+ };
+
+Again, notice how board-specific information is provided; each chip may need
+several types. This example shows generic constraints like the fastest SPI
+clock to allow (a function of board voltage in this case) or how an IRQ pin
+is wired, plus chip-specific constraints like an important delay that's
+changed by the capacitance at one pin.
+
+(There's also "controller_data", information that may be useful to the
+controller driver. An example would be peripheral-specific DMA tuning
+data or chipselect callbacks. This is stored in spi_device later.)
+
+The board_info should provide enough information to let the system work
+without the chip's driver being loaded. The most troublesome aspect of
+that is likely the SPI_CS_HIGH bit in the spi_device.mode field, since
+sharing a bus with a device that interprets chipselect "backwards" is
+not possible.
+
+Then your board initialization code would register that table with the SPI
+infrastructure, so that it's available later when the SPI master controller
+driver is registered:
+
+ spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
+
+Like with other static board-specific setup, you won't unregister those.
+
+The widely used "card" style computers bundle memory, cpu, and little else
+onto a card that's maybe just thirty square centimeters. On such systems,
+your arch/.../mach-.../board-*.c file would primarily provide information
+about the devices on the mainboard into which such a card is plugged. That
+certainly includes SPI devices hooked up through the card connectors!
+
+
+NON-STATIC CONFIGURATIONS
+
+Developer boards often play by different rules than product boards, and one
+example is the potential need to hotplug SPI devices and/or controllers.
+
+For those cases you might need to use use spi_busnum_to_master() to look
+up the spi bus master, and will likely need spi_new_device() to provide the
+board info based on the board that was hotplugged. Of course, you'd later
+call at least spi_unregister_device() when that board is removed.
+
+When Linux includes support for MMC/SD/SDIO/DataFlash cards through SPI, those
+configurations will also be dynamic. Fortunately, those devices all support
+basic device identification probes, so that support should hotplug normally.
+
+
+How do I write an "SPI Protocol Driver"?
+----------------------------------------
+All SPI drivers are currently kernel drivers. A userspace driver API
+would just be another kernel driver, probably offering some lowlevel
+access through aio_read(), aio_write(), and ioctl() calls and using the
+standard userspace sysfs mechanisms to bind to a given SPI device.
+
+SPI protocol drivers somewhat resemble platform device drivers:
+
+ static struct spi_driver CHIP_driver = {
+ .driver = {
+ .name = "CHIP",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+
+ .probe = CHIP_probe,
+ .remove = __devexit_p(CHIP_remove),
+ .suspend = CHIP_suspend,
+ .resume = CHIP_resume,
+ };
+
+The driver core will autmatically attempt to bind this driver to any SPI
+device whose board_info gave a modalias of "CHIP". Your probe() code
+might look like this unless you're creating a class_device:
+
+ static int __devinit CHIP_probe(struct spi_device *spi)
+ {
+ struct CHIP *chip;
+ struct CHIP_platform_data *pdata;
+
+ /* assuming the driver requires board-specific data: */
+ pdata = &spi->dev.platform_data;
+ if (!pdata)
+ return -ENODEV;
+
+ /* get memory for driver's per-chip state */
+ chip = kzalloc(sizeof *chip, GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+ dev_set_drvdata(&spi->dev, chip);
+
+ ... etc
+ return 0;
+ }
+
+As soon as it enters probe(), the driver may issue I/O requests to
+the SPI device using "struct spi_message". When remove() returns,
+the driver guarantees that it won't submit any more such messages.
+
+ - An spi_message is a sequence of of protocol operations, executed
+ as one atomic sequence. SPI driver controls include:
+
+ + when bidirectional reads and writes start ... by how its
+ sequence of spi_transfer requests is arranged;
+
+ + optionally defining short delays after transfers ... using
+ the spi_transfer.delay_usecs setting;
+
+ + whether the chipselect becomes inactive after a transfer and
+ any delay ... by using the spi_transfer.cs_change flag;
+
+ + hinting whether the next message is likely to go to this same
+ device ... using the spi_transfer.cs_change flag on the last
+ transfer in that atomic group, and potentially saving costs
+ for chip deselect and select operations.
+
+ - Follow standard kernel rules, and provide DMA-safe buffers in
+ your messages. That way controller drivers using DMA aren't forced
+ to make extra copies unless the hardware requires it (e.g. working
+ around hardware errata that force the use of bounce buffering).
+
+ If standard dma_map_single() handling of these buffers is inappropriate,
+ you can use spi_message.is_dma_mapped to tell the controller driver
+ that you've already provided the relevant DMA addresses.
+
+ - The basic I/O primitive is spi_async(). Async requests may be
+ issued in any context (irq handler, task, etc) and completion
+ is reported using a callback provided with the message.
+ After any detected error, the chip is deselected and processing
+ of that spi_message is aborted.
+
+ - There are also synchronous wrappers like spi_sync(), and wrappers
+ like spi_read(), spi_write(), and spi_write_then_read(). These
+ may be issued only in contexts that may sleep, and they're all
+ clean (and small, and "optional") layers over spi_async().
+
+ - The spi_write_then_read() call, and convenience wrappers around
+ it, should only be used with small amounts of data where the
+ cost of an extra copy may be ignored. It's designed to support
+ common RPC-style requests, such as writing an eight bit command
+ and reading a sixteen bit response -- spi_w8r16() being one its
+ wrappers, doing exactly that.
+
+Some drivers may need to modify spi_device characteristics like the
+transfer mode, wordsize, or clock rate. This is done with spi_setup(),
+which would normally be called from probe() before the first I/O is
+done to the device.
+
+While "spi_device" would be the bottom boundary of the driver, the
+upper boundaries might include sysfs (especially for sensor readings),
+the input layer, ALSA, networking, MTD, the character device framework,
+or other Linux subsystems.
+
+Note that there are two types of memory your driver must manage as part
+of interacting with SPI devices.
+
+ - I/O buffers use the usual Linux rules, and must be DMA-safe.
+ You'd normally allocate them from the heap or free page pool.
+ Don't use the stack, or anything that's declared "static".
+
+ - The spi_message and spi_transfer metadata used to glue those
+ I/O buffers into a group of protocol transactions. These can
+ be allocated anywhere it's convenient, including as part of
+ other allocate-once driver data structures. Zero-init these.
+
+If you like, spi_message_alloc() and spi_message_free() convenience
+routines are available to allocate and zero-initialize an spi_message
+with several transfers.
+
+
+How do I write an "SPI Master Controller Driver"?
+-------------------------------------------------
+An SPI controller will probably be registered on the platform_bus; write
+a driver to bind to the device, whichever bus is involved.
+
+The main task of this type of driver is to provide an "spi_master".
+Use spi_alloc_master() to allocate the master, and class_get_devdata()
+to get the driver-private data allocated for that device.
+
+ struct spi_master *master;
+ struct CONTROLLER *c;
+
+ master = spi_alloc_master(dev, sizeof *c);
+ if (!master)
+ return -ENODEV;
+
+ c = class_get_devdata(&master->cdev);
+
+The driver will initialize the fields of that spi_master, including the
+bus number (maybe the same as the platform device ID) and three methods
+used to interact with the SPI core and SPI protocol drivers. It will
+also initialize its own internal state.
+
+ master->setup(struct spi_device *spi)
+ This sets up the device clock rate, SPI mode, and word sizes.
+ Drivers may change the defaults provided by board_info, and then
+ call spi_setup(spi) to invoke this routine. It may sleep.
+
+ master->transfer(struct spi_device *spi, struct spi_message *message)
+ This must not sleep. Its responsibility is arrange that the
+ transfer happens and its complete() callback is issued; the two
+ will normally happen later, after other transfers complete.
+
+ master->cleanup(struct spi_device *spi)
+ Your controller driver may use spi_device.controller_state to hold
+ state it dynamically associates with that device. If you do that,
+ be sure to provide the cleanup() method to free that state.
+
+The bulk of the driver will be managing the I/O queue fed by transfer().
+
+That queue could be purely conceptual. For example, a driver used only
+for low-frequency sensor acess might be fine using synchronous PIO.
+
+But the queue will probably be very real, using message->queue, PIO,
+often DMA (especially if the root filesystem is in SPI flash), and
+execution contexts like IRQ handlers, tasklets, or workqueues (such
+as keventd). Your driver can be as fancy, or as simple, as you need.
+
+
+THANKS TO
+---------
+Contributors to Linux-SPI discussions include (in alphabetical order,
+by last name):
+
+David Brownell
+Russell King
+Dmitry Pervushin
+Stephen Street
+Mark Underwood
+Andrew Victor
+Vitaly Wool
+
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 50b9afa..3cfd82a 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -729,6 +729,8 @@
source "drivers/i2c/Kconfig"
+source "drivers/spi/Kconfig"
+
source "drivers/hwmon/Kconfig"
#source "drivers/l3/Kconfig"
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 48f446d..283c089 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -44,6 +44,8 @@
source "drivers/i2c/Kconfig"
+source "drivers/spi/Kconfig"
+
source "drivers/w1/Kconfig"
source "drivers/hwmon/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 7fc3f0f..7c45050 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -41,6 +41,7 @@
obj-$(CONFIG_IEEE1394) += ieee1394/
obj-y += cdrom/
obj-$(CONFIG_MTD) += mtd/
+obj-$(CONFIG_SPI) += spi/
obj-$(CONFIG_PCCARD) += pcmcia/
obj-$(CONFIG_DIO) += dio/
obj-$(CONFIG_SBUS) += sbus/
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index 21d55ed..2c67402 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -11,6 +11,19 @@
if INPUT_TOUCHSCREEN
+config TOUCHSCREEN_ADS7846
+ tristate "ADS 7846 based touchscreens"
+ depends on SPI_MASTER
+ help
+ Say Y here if you have a touchscreen interface using the
+ ADS7846 controller, and your board-specific initialization
+ code includes that in its table of SPI devices.
+
+ If unsure, say N (but it's safe to say "Y").
+
+ To compile this driver as a module, choose M here: the
+ module will be called ads7846.
+
config TOUCHSCREEN_BITSY
tristate "Compaq iPAQ H3600 (Bitsy) touchscreen"
depends on SA1100_BITSY
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index 6842869..5e5557c 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -4,6 +4,7 @@
# Each configuration option enables a list of files.
+obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o
obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
new file mode 100644
index 0000000..dd8c6a9
--- /dev/null
+++ b/drivers/input/touchscreen/ads7846.c
@@ -0,0 +1,625 @@
+/*
+ * ADS7846 based touchscreen and sensor driver
+ *
+ * Copyright (c) 2005 David Brownell
+ *
+ * Using code from:
+ * - corgi_ts.c
+ * Copyright (C) 2004-2005 Richard Purdie
+ * - omap_ts.[hc], ads7846.h, ts_osk.c
+ * Copyright (C) 2002 MontaVista Software
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2005 Dirk Behme
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+#ifdef CONFIG_ARM
+#include <asm/mach-types.h>
+#ifdef CONFIG_ARCH_OMAP
+#include <asm/arch/gpio.h>
+#endif
+
+#else
+#define set_irq_type(irq,type) do{}while(0)
+#endif
+
+
+/*
+ * This code has been lightly tested on an ads7846.
+ * Support for ads7843 and ads7845 has only been stubbed in.
+ *
+ * Not yet done: investigate the values reported. Are x/y/pressure
+ * event values sane enough for X11? How accurate are the temperature
+ * and voltage readings? (System-specific calibration should support
+ * accuracy of 0.3 degrees C; otherwise it's 2.0 degrees.)
+ *
+ * app note sbaa036 talks in more detail about accurate sampling...
+ * that ought to help in situations like LCDs inducing noise (which
+ * can also be helped by using synch signals) and more generally.
+ */
+
+#define TS_POLL_PERIOD msecs_to_jiffies(10)
+
+struct ts_event {
+ /* For portability, we can't read 12 bit values using SPI (which
+ * would make the controller deliver them as native byteorder u16
+ * with msbs zeroed). Instead, we read them as two 8-byte values,
+ * which need byteswapping then range adjustment.
+ */
+ __be16 x;
+ __be16 y;
+ __be16 z1, z2;
+};
+
+struct ads7846 {
+ struct input_dev input;
+ char phys[32];
+
+ struct spi_device *spi;
+ u16 model;
+ u16 vref_delay_usecs;
+ u16 x_plate_ohms;
+
+ struct ts_event tc;
+
+ struct spi_transfer xfer[8];
+ struct spi_message msg;
+
+ spinlock_t lock;
+ struct timer_list timer; /* P: lock */
+ unsigned pendown:1; /* P: lock */
+ unsigned pending:1; /* P: lock */
+// FIXME remove "irq_disabled"
+ unsigned irq_disabled:1; /* P: lock */
+};
+
+/* leave chip selected when we're done, for quicker re-select? */
+#if 0
+#define CS_CHANGE(xfer) ((xfer).cs_change = 1)
+#else
+#define CS_CHANGE(xfer) ((xfer).cs_change = 0)
+#endif
+
+/*--------------------------------------------------------------------------*/
+
+/* The ADS7846 has touchscreen and other sensors.
+ * Earlier ads784x chips are somewhat compatible.
+ */
+#define ADS_START (1 << 7)
+#define ADS_A2A1A0_d_y (1 << 4) /* differential */
+#define ADS_A2A1A0_d_z1 (3 << 4) /* differential */
+#define ADS_A2A1A0_d_z2 (4 << 4) /* differential */
+#define ADS_A2A1A0_d_x (5 << 4) /* differential */
+#define ADS_A2A1A0_temp0 (0 << 4) /* non-differential */
+#define ADS_A2A1A0_vbatt (2 << 4) /* non-differential */
+#define ADS_A2A1A0_vaux (6 << 4) /* non-differential */
+#define ADS_A2A1A0_temp1 (7 << 4) /* non-differential */
+#define ADS_8_BIT (1 << 3)
+#define ADS_12_BIT (0 << 3)
+#define ADS_SER (1 << 2) /* non-differential */
+#define ADS_DFR (0 << 2) /* differential */
+#define ADS_PD10_PDOWN (0 << 0) /* lowpower mode + penirq */
+#define ADS_PD10_ADC_ON (1 << 0) /* ADC on */
+#define ADS_PD10_REF_ON (2 << 0) /* vREF on + penirq */
+#define ADS_PD10_ALL_ON (3 << 0) /* ADC + vREF on */
+
+#define MAX_12BIT ((1<<12)-1)
+
+/* leave ADC powered up (disables penirq) between differential samples */
+#define READ_12BIT_DFR(x) (ADS_START | ADS_A2A1A0_d_ ## x \
+ | ADS_12_BIT | ADS_DFR)
+
+static const u8 read_y = READ_12BIT_DFR(y) | ADS_PD10_ADC_ON;
+static const u8 read_z1 = READ_12BIT_DFR(z1) | ADS_PD10_ADC_ON;
+static const u8 read_z2 = READ_12BIT_DFR(z2) | ADS_PD10_ADC_ON;
+static const u8 read_x = READ_12BIT_DFR(x) | ADS_PD10_PDOWN; /* LAST */
+
+/* single-ended samples need to first power up reference voltage;
+ * we leave both ADC and VREF powered
+ */
+#define READ_12BIT_SER(x) (ADS_START | ADS_A2A1A0_ ## x \
+ | ADS_12_BIT | ADS_SER)
+
+static const u8 ref_on = READ_12BIT_DFR(x) | ADS_PD10_ALL_ON;
+static const u8 ref_off = READ_12BIT_DFR(y) | ADS_PD10_PDOWN;
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * Non-touchscreen sensors only use single-ended conversions.
+ */
+
+struct ser_req {
+ u8 command;
+ u16 scratch;
+ __be16 sample;
+ struct spi_message msg;
+ struct spi_transfer xfer[6];
+};
+
+static int ads7846_read12_ser(struct device *dev, unsigned command)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct ads7846 *ts = dev_get_drvdata(dev);
+ struct ser_req *req = kzalloc(sizeof *req, SLAB_KERNEL);
+ int status;
+ int sample;
+ int i;
+
+ if (!req)
+ return -ENOMEM;
+
+ INIT_LIST_HEAD(&req->msg.transfers);
+
+ /* activate reference, so it has time to settle; */
+ req->xfer[0].tx_buf = &ref_on;
+ req->xfer[0].len = 1;
+ req->xfer[1].rx_buf = &req->scratch;
+ req->xfer[1].len = 2;
+
+ /*
+ * for external VREF, 0 usec (and assume it's always on);
+ * for 1uF, use 800 usec;
+ * no cap, 100 usec.
+ */
+ req->xfer[1].delay_usecs = ts->vref_delay_usecs;
+
+ /* take sample */
+ req->command = (u8) command;
+ req->xfer[2].tx_buf = &req->command;
+ req->xfer[2].len = 1;
+ req->xfer[3].rx_buf = &req->sample;
+ req->xfer[3].len = 2;
+
+ /* REVISIT: take a few more samples, and compare ... */
+
+ /* turn off reference */
+ req->xfer[4].tx_buf = &ref_off;
+ req->xfer[4].len = 1;
+ req->xfer[5].rx_buf = &req->scratch;
+ req->xfer[5].len = 2;
+
+ CS_CHANGE(req->xfer[5]);
+
+ /* group all the transfers together, so we can't interfere with
+ * reading touchscreen state; disable penirq while sampling
+ */
+ for (i = 0; i < 6; i++)
+ spi_message_add_tail(&req->xfer[i], &req->msg);
+
+ disable_irq(spi->irq);
+ status = spi_sync(spi, &req->msg);
+ enable_irq(spi->irq);
+
+ if (req->msg.status)
+ status = req->msg.status;
+ sample = be16_to_cpu(req->sample);
+ sample = sample >> 4;
+ kfree(req);
+
+ return status ? status : sample;
+}
+
+#define SHOW(name) static ssize_t \
+name ## _show(struct device *dev, struct device_attribute *attr, char *buf) \
+{ \
+ ssize_t v = ads7846_read12_ser(dev, \
+ READ_12BIT_SER(name) | ADS_PD10_ALL_ON); \
+ if (v < 0) \
+ return v; \
+ return sprintf(buf, "%u\n", (unsigned) v); \
+} \
+static DEVICE_ATTR(name, S_IRUGO, name ## _show, NULL);
+
+SHOW(temp0)
+SHOW(temp1)
+SHOW(vaux)
+SHOW(vbatt)
+
+/*--------------------------------------------------------------------------*/
+
+/*
+ * PENIRQ only kicks the timer. The timer only reissues the SPI transfer,
+ * to retrieve touchscreen status.
+ *
+ * The SPI transfer completion callback does the real work. It reports
+ * touchscreen events and reactivates the timer (or IRQ) as appropriate.
+ */
+
+static void ads7846_rx(void *ads)
+{
+ struct ads7846 *ts = ads;
+ unsigned Rt;
+ unsigned sync = 0;
+ u16 x, y, z1, z2;
+ unsigned long flags;
+
+ /* adjust: 12 bit samples (left aligned), built from
+ * two 8 bit values writen msb-first.
+ */
+ x = be16_to_cpu(ts->tc.x) >> 4;
+ y = be16_to_cpu(ts->tc.y) >> 4;
+ z1 = be16_to_cpu(ts->tc.z1) >> 4;
+ z2 = be16_to_cpu(ts->tc.z2) >> 4;
+
+ /* range filtering */
+ if (x == MAX_12BIT)
+ x = 0;
+
+ if (x && z1 && ts->spi->dev.power.power_state.event == PM_EVENT_ON) {
+ /* compute touch pressure resistance using equation #2 */
+ Rt = z2;
+ Rt -= z1;
+ Rt *= x;
+ Rt *= ts->x_plate_ohms;
+ Rt /= z1;
+ Rt = (Rt + 2047) >> 12;
+ } else
+ Rt = 0;
+
+ /* NOTE: "pendown" is inferred from pressure; we don't rely on
+ * being able to check nPENIRQ status, or "friendly" trigger modes
+ * (both-edges is much better than just-falling or low-level).
+ *
+ * REVISIT: some boards may require reading nPENIRQ; it's
+ * needed on 7843. and 7845 reads pressure differently...
+ *
+ * REVISIT: the touchscreen might not be connected; this code
+ * won't notice that, even if nPENIRQ never fires ...
+ */
+ if (!ts->pendown && Rt != 0) {
+ input_report_key(&ts->input, BTN_TOUCH, 1);
+ sync = 1;
+ } else if (ts->pendown && Rt == 0) {
+ input_report_key(&ts->input, BTN_TOUCH, 0);
+ sync = 1;
+ }
+
+ if (Rt) {
+ input_report_abs(&ts->input, ABS_X, x);
+ input_report_abs(&ts->input, ABS_Y, y);
+ input_report_abs(&ts->input, ABS_PRESSURE, Rt);
+ sync = 1;
+ }
+ if (sync)
+ input_sync(&ts->input);
+
+#ifdef VERBOSE
+ if (Rt || ts->pendown)
+ pr_debug("%s: %d/%d/%d%s\n", ts->spi->dev.bus_id,
+ x, y, Rt, Rt ? "" : " UP");
+#endif
+
+ /* don't retrigger while we're suspended */
+ spin_lock_irqsave(&ts->lock, flags);
+
+ ts->pendown = (Rt != 0);
+ ts->pending = 0;
+
+ if (ts->spi->dev.power.power_state.event == PM_EVENT_ON) {
+ if (ts->pendown)
+ mod_timer(&ts->timer, jiffies + TS_POLL_PERIOD);
+ else if (ts->irq_disabled) {
+ ts->irq_disabled = 0;
+ enable_irq(ts->spi->irq);
+ }
+ }
+
+ spin_unlock_irqrestore(&ts->lock, flags);
+}
+
+static void ads7846_timer(unsigned long handle)
+{
+ struct ads7846 *ts = (void *)handle;
+ int status = 0;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ts->lock, flags);
+ if (!ts->pending) {
+ ts->pending = 1;
+ if (!ts->irq_disabled) {
+ ts->irq_disabled = 1;
+ disable_irq(ts->spi->irq);
+ }
+ status = spi_async(ts->spi, &ts->msg);
+ if (status)
+ dev_err(&ts->spi->dev, "spi_async --> %d\n",
+ status);
+ }
+ spin_unlock_irqrestore(&ts->lock, flags);
+}
+
+static irqreturn_t ads7846_irq(int irq, void *handle, struct pt_regs *regs)
+{
+ ads7846_timer((unsigned long) handle);
+ return IRQ_HANDLED;
+}
+
+/*--------------------------------------------------------------------------*/
+
+static int
+ads7846_suspend(struct spi_device *spi, pm_message_t message)
+{
+ struct ads7846 *ts = dev_get_drvdata(&spi->dev);
+ unsigned long flags;
+
+ spin_lock_irqsave(&ts->lock, flags);
+
+ spi->dev.power.power_state = message;
+
+ /* are we waiting for IRQ, or polling? */
+ if (!ts->pendown) {
+ if (!ts->irq_disabled) {
+ ts->irq_disabled = 1;
+ disable_irq(ts->spi->irq);
+ }
+ } else {
+ /* polling; force a final SPI completion;
+ * that will clean things up neatly
+ */
+ if (!ts->pending)
+ mod_timer(&ts->timer, jiffies);
+
+ while (ts->pendown || ts->pending) {
+ spin_unlock_irqrestore(&ts->lock, flags);
+ udelay(10);
+ spin_lock_irqsave(&ts->lock, flags);
+ }
+ }
+
+ /* we know the chip's in lowpower mode since we always
+ * leave it that way after every request
+ */
+
+ spin_unlock_irqrestore(&ts->lock, flags);
+ return 0;
+}
+
+static int ads7846_resume(struct spi_device *spi)
+{
+ struct ads7846 *ts = dev_get_drvdata(&spi->dev);
+
+ ts->irq_disabled = 0;
+ enable_irq(ts->spi->irq);
+ spi->dev.power.power_state = PMSG_ON;
+ return 0;
+}
+
+static int __devinit ads7846_probe(struct spi_device *spi)
+{
+ struct ads7846 *ts;
+ struct ads7846_platform_data *pdata = spi->dev.platform_data;
+ struct spi_transfer *x;
+ int i;
+
+ if (!spi->irq) {
+ dev_dbg(&spi->dev, "no IRQ?\n");
+ return -ENODEV;
+ }
+
+ if (!pdata) {
+ dev_dbg(&spi->dev, "no platform data?\n");
+ return -ENODEV;
+ }
+
+ /* don't exceed max specified sample rate */
+ if (spi->max_speed_hz > (125000 * 16)) {
+ dev_dbg(&spi->dev, "f(sample) %d KHz?\n",
+ (spi->max_speed_hz/16)/1000);
+ return -EINVAL;
+ }
+
+ /* We'd set the wordsize to 12 bits ... except that some controllers
+ * will then treat the 8 bit command words as 12 bits (and drop the
+ * four MSBs of the 12 bit result). Result: inputs must be shifted
+ * to discard the four garbage LSBs.
+ */
+
+ if (!(ts = kzalloc(sizeof(struct ads7846), GFP_KERNEL)))
+ return -ENOMEM;
+
+ dev_set_drvdata(&spi->dev, ts);
+
+ ts->spi = spi;
+ spi->dev.power.power_state = PMSG_ON;
+
+ init_timer(&ts->timer);
+ ts->timer.data = (unsigned long) ts;
+ ts->timer.function = ads7846_timer;
+
+ ts->model = pdata->model ? : 7846;
+ ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
+ ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
+
+ init_input_dev(&ts->input);
+
+ ts->input.dev = &spi->dev;
+ ts->input.name = "ADS784x Touchscreen";
+ snprintf(ts->phys, sizeof ts->phys, "%s/input0", spi->dev.bus_id);
+ ts->input.phys = ts->phys;
+
+ ts->input.evbit[0] = BIT(EV_KEY) | BIT(EV_ABS);
+ ts->input.keybit[LONG(BTN_TOUCH)] = BIT(BTN_TOUCH);
+ input_set_abs_params(&ts->input, ABS_X,
+ pdata->x_min ? : 0,
+ pdata->x_max ? : MAX_12BIT,
+ 0, 0);
+ input_set_abs_params(&ts->input, ABS_Y,
+ pdata->y_min ? : 0,
+ pdata->y_max ? : MAX_12BIT,
+ 0, 0);
+ input_set_abs_params(&ts->input, ABS_PRESSURE,
+ pdata->pressure_min, pdata->pressure_max, 0, 0);
+
+ input_register_device(&ts->input);
+
+ /* set up the transfers to read touchscreen state; this assumes we
+ * use formula #2 for pressure, not #3.
+ */
+ x = ts->xfer;
+
+ /* y- still on; turn on only y+ (and ADC) */
+ x->tx_buf = &read_y;
+ x->len = 1;
+ x++;
+ x->rx_buf = &ts->tc.y;
+ x->len = 2;
+ x++;
+
+ /* turn y+ off, x- on; we'll use formula #2 */
+ if (ts->model == 7846) {
+ x->tx_buf = &read_z1;
+ x->len = 1;
+ x++;
+ x->rx_buf = &ts->tc.z1;
+ x->len = 2;
+ x++;
+
+ x->tx_buf = &read_z2;
+ x->len = 1;
+ x++;
+ x->rx_buf = &ts->tc.z2;
+ x->len = 2;
+ x++;
+ }
+
+ /* turn y- off, x+ on, then leave in lowpower */
+ x->tx_buf = &read_x;
+ x->len = 1;
+ x++;
+ x->rx_buf = &ts->tc.x;
+ x->len = 2;
+ x++;
+
+ CS_CHANGE(x[-1]);
+
+ for (i = 0; i < x - ts->xfer; i++)
+ spi_message_add_tail(&ts->xfer[i], &ts->msg);
+ ts->msg.complete = ads7846_rx;
+ ts->msg.context = ts;
+
+ if (request_irq(spi->irq, ads7846_irq, SA_SAMPLE_RANDOM,
+ spi->dev.bus_id, ts)) {
+ dev_dbg(&spi->dev, "irq %d busy?\n", spi->irq);
+ input_unregister_device(&ts->input);
+ kfree(ts);
+ return -EBUSY;
+ }
+ set_irq_type(spi->irq, IRQT_FALLING);
+
+ dev_info(&spi->dev, "touchscreen, irq %d\n", spi->irq);
+
+ /* take a first sample, leaving nPENIRQ active; avoid
+ * the touchscreen, in case it's not connected.
+ */
+ (void) ads7846_read12_ser(&spi->dev,
+ READ_12BIT_SER(vaux) | ADS_PD10_ALL_ON);
+
+ /* ads7843/7845 don't have temperature sensors, and
+ * use the other sensors a bit differently too
+ */
+ if (ts->model == 7846) {
+ device_create_file(&spi->dev, &dev_attr_temp0);
+ device_create_file(&spi->dev, &dev_attr_temp1);
+ }
+ if (ts->model != 7845)
+ device_create_file(&spi->dev, &dev_attr_vbatt);
+ device_create_file(&spi->dev, &dev_attr_vaux);
+
+ return 0;
+}
+
+static int __devexit ads7846_remove(struct spi_device *spi)
+{
+ struct ads7846 *ts = dev_get_drvdata(&spi->dev);
+
+ ads7846_suspend(spi, PMSG_SUSPEND);
+ free_irq(ts->spi->irq, ts);
+ if (ts->irq_disabled)
+ enable_irq(ts->spi->irq);
+
+ if (ts->model == 7846) {
+ device_remove_file(&spi->dev, &dev_attr_temp0);
+ device_remove_file(&spi->dev, &dev_attr_temp1);
+ }
+ if (ts->model != 7845)
+ device_remove_file(&spi->dev, &dev_attr_vbatt);
+ device_remove_file(&spi->dev, &dev_attr_vaux);
+
+ input_unregister_device(&ts->input);
+ kfree(ts);
+
+ dev_dbg(&spi->dev, "unregistered touchscreen\n");
+ return 0;
+}
+
+static struct spi_driver ads7846_driver = {
+ .driver = {
+ .name = "ads7846",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+ .probe = ads7846_probe,
+ .remove = __devexit_p(ads7846_remove),
+ .suspend = ads7846_suspend,
+ .resume = ads7846_resume,
+};
+
+static int __init ads7846_init(void)
+{
+ /* grr, board-specific init should stay out of drivers!! */
+
+#ifdef CONFIG_ARCH_OMAP
+ if (machine_is_omap_osk()) {
+ /* GPIO4 = PENIRQ; GPIO6 = BUSY */
+ omap_request_gpio(4);
+ omap_set_gpio_direction(4, 1);
+ omap_request_gpio(6);
+ omap_set_gpio_direction(6, 1);
+ }
+ // also TI 1510 Innovator, bitbanging through FPGA
+ // also Nokia 770
+ // also Palm Tungsten T2
+#endif
+
+ // PXA:
+ // also Dell Axim X50
+ // also HP iPaq H191x/H192x/H415x/H435x
+ // also Intel Lubbock (additional to UCB1400; as temperature sensor)
+ // also Sharp Zaurus C7xx, C8xx (corgi/sheperd/husky)
+
+ // Atmel at91sam9261-EK uses ads7843
+
+ // also various AMD Au1x00 devel boards
+
+ return spi_register_driver(&ads7846_driver);
+}
+module_init(ads7846_init);
+
+static void __exit ads7846_exit(void)
+{
+ spi_unregister_driver(&ads7846_driver);
+
+#ifdef CONFIG_ARCH_OMAP
+ if (machine_is_omap_osk()) {
+ omap_free_gpio(4);
+ omap_free_gpio(6);
+ }
+#endif
+
+}
+module_exit(ads7846_exit);
+
+MODULE_DESCRIPTION("ADS7846 TouchScreen Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/mtd/devices/Kconfig b/drivers/mtd/devices/Kconfig
index 9a2aa40..5038e90 100644
--- a/drivers/mtd/devices/Kconfig
+++ b/drivers/mtd/devices/Kconfig
@@ -47,6 +47,22 @@
accelerator. Say Y here if you have a DECstation 5000/2x0 or a
DECsystem 5900 equipped with such a module.
+config MTD_DATAFLASH
+ tristate "Support for AT45xxx DataFlash"
+ depends on MTD && SPI_MASTER && EXPERIMENTAL
+ help
+ This enables access to AT45xxx DataFlash chips, using SPI.
+ Sometimes DataFlash chips are packaged inside MMC-format
+ cards; at this writing, the MMC stack won't handle those.
+
+config MTD_M25P80
+ tristate "Support for M25 SPI Flash"
+ depends on MTD && SPI_MASTER && EXPERIMENTAL
+ help
+ This enables access to ST M25P80 and similar SPI flash chips,
+ used for program and data storage. Set up your spi devices
+ with the right board-specific platform data.
+
config MTD_SLRAM
tristate "Uncached system RAM"
depends on MTD
diff --git a/drivers/mtd/devices/Makefile b/drivers/mtd/devices/Makefile
index e38db34..7c5ed21 100644
--- a/drivers/mtd/devices/Makefile
+++ b/drivers/mtd/devices/Makefile
@@ -23,3 +23,5 @@
obj-$(CONFIG_MTD_LART) += lart.o
obj-$(CONFIG_MTD_BLKMTD) += blkmtd.o
obj-$(CONFIG_MTD_BLOCK2MTD) += block2mtd.o
+obj-$(CONFIG_MTD_DATAFLASH) += mtd_dataflash.o
+obj-$(CONFIG_MTD_M25P80) += m25p80.o
diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
new file mode 100644
index 0000000..d5f2408
--- /dev/null
+++ b/drivers/mtd/devices/m25p80.c
@@ -0,0 +1,582 @@
+/*
+ * MTD SPI driver for ST M25Pxx flash chips
+ *
+ * Author: Mike Lavender, mike@steroidmicros.com
+ *
+ * Copyright (c) 2005, Intec Automation Inc.
+ *
+ * Some parts are based on lart.c by Abraham Van Der Merwe
+ *
+ * Cleaned up and generalized based on mtd_dataflash.c
+ *
+ * This code is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/interrupt.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <asm/semaphore.h>
+
+
+/* NOTE: AT 25F and SST 25LF series are very similar,
+ * but commands for sector erase and chip id differ...
+ */
+
+#define FLASH_PAGESIZE 256
+
+/* Flash opcodes. */
+#define OPCODE_WREN 6 /* Write enable */
+#define OPCODE_RDSR 5 /* Read status register */
+#define OPCODE_READ 3 /* Read data bytes */
+#define OPCODE_PP 2 /* Page program */
+#define OPCODE_SE 0xd8 /* Sector erase */
+#define OPCODE_RES 0xab /* Read Electronic Signature */
+#define OPCODE_RDID 0x9f /* Read JEDEC ID */
+
+/* Status Register bits. */
+#define SR_WIP 1 /* Write in progress */
+#define SR_WEL 2 /* Write enable latch */
+#define SR_BP0 4 /* Block protect 0 */
+#define SR_BP1 8 /* Block protect 1 */
+#define SR_BP2 0x10 /* Block protect 2 */
+#define SR_SRWD 0x80 /* SR write protect */
+
+/* Define max times to check status register before we give up. */
+#define MAX_READY_WAIT_COUNT 100000
+
+
+#ifdef CONFIG_MTD_PARTITIONS
+#define mtd_has_partitions() (1)
+#else
+#define mtd_has_partitions() (0)
+#endif
+
+/****************************************************************************/
+
+struct m25p {
+ struct spi_device *spi;
+ struct semaphore lock;
+ struct mtd_info mtd;
+ unsigned partitioned;
+ u8 command[4];
+};
+
+static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
+{
+ return container_of(mtd, struct m25p, mtd);
+}
+
+/****************************************************************************/
+
+/*
+ * Internal helper functions
+ */
+
+/*
+ * Read the status register, returning its value in the location
+ * Return the status register value.
+ * Returns negative if error occurred.
+ */
+static int read_sr(struct m25p *flash)
+{
+ ssize_t retval;
+ u8 code = OPCODE_RDSR;
+ u8 val;
+
+ retval = spi_write_then_read(flash->spi, &code, 1, &val, 1);
+
+ if (retval < 0) {
+ dev_err(&flash->spi->dev, "error %d reading SR\n",
+ (int) retval);
+ return retval;
+ }
+
+ return val;
+}
+
+
+/*
+ * Set write enable latch with Write Enable command.
+ * Returns negative if error occurred.
+ */
+static inline int write_enable(struct m25p *flash)
+{
+ u8 code = OPCODE_WREN;
+
+ return spi_write_then_read(flash->spi, &code, 1, NULL, 0);
+}
+
+
+/*
+ * Service routine to read status register until ready, or timeout occurs.
+ * Returns non-zero if error.
+ */
+static int wait_till_ready(struct m25p *flash)
+{
+ int count;
+ int sr;
+
+ /* one chip guarantees max 5 msec wait here after page writes,
+ * but potentially three seconds (!) after page erase.
+ */
+ for (count = 0; count < MAX_READY_WAIT_COUNT; count++) {
+ if ((sr = read_sr(flash)) < 0)
+ break;
+ else if (!(sr & SR_WIP))
+ return 0;
+
+ /* REVISIT sometimes sleeping would be best */
+ }
+
+ return 1;
+}
+
+
+/*
+ * Erase one sector of flash memory at offset ``offset'' which is any
+ * address within the sector which should be erased.
+ *
+ * Returns 0 if successful, non-zero otherwise.
+ */
+static int erase_sector(struct m25p *flash, u32 offset)
+{
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: %s at 0x%08x\n", flash->spi->dev.bus_id,
+ __FUNCTION__, offset);
+
+ /* Wait until finished previous write command. */
+ if (wait_till_ready(flash))
+ return 1;
+
+ /* Send write enable, then erase commands. */
+ write_enable(flash);
+
+ /* Set up command buffer. */
+ flash->command[0] = OPCODE_SE;
+ flash->command[1] = offset >> 16;
+ flash->command[2] = offset >> 8;
+ flash->command[3] = offset;
+
+ spi_write(flash->spi, flash->command, sizeof(flash->command));
+
+ return 0;
+}
+
+/****************************************************************************/
+
+/*
+ * MTD implementation
+ */
+
+/*
+ * Erase an address range on the flash chip. The address range may extend
+ * one or more erase sectors. Return an error is there is a problem erasing.
+ */
+static int m25p80_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct m25p *flash = mtd_to_m25p(mtd);
+ u32 addr,len;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: %s %s 0x%08x, len %zd\n",
+ flash->spi->dev.bus_id, __FUNCTION__, "at",
+ (u32)instr->addr, instr->len);
+
+ /* sanity checks */
+ if (instr->addr + instr->len > flash->mtd.size)
+ return -EINVAL;
+ if ((instr->addr % mtd->erasesize) != 0
+ || (instr->len % mtd->erasesize) != 0) {
+ return -EINVAL;
+ }
+
+ addr = instr->addr;
+ len = instr->len;
+
+ down(&flash->lock);
+
+ /* now erase those sectors */
+ while (len) {
+ if (erase_sector(flash, addr)) {
+ instr->state = MTD_ERASE_FAILED;
+ up(&flash->lock);
+ return -EIO;
+ }
+
+ addr += mtd->erasesize;
+ len -= mtd->erasesize;
+ }
+
+ up(&flash->lock);
+
+ instr->state = MTD_ERASE_DONE;
+ mtd_erase_callback(instr);
+
+ return 0;
+}
+
+/*
+ * Read an address range from the flash chip. The address range
+ * may be any size provided it is within the physical boundaries.
+ */
+static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct m25p *flash = mtd_to_m25p(mtd);
+ struct spi_transfer t[2];
+ struct spi_message m;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: %s %s 0x%08x, len %zd\n",
+ flash->spi->dev.bus_id, __FUNCTION__, "from",
+ (u32)from, len);
+
+ /* sanity checks */
+ if (!len)
+ return 0;
+
+ if (from + len > flash->mtd.size)
+ return -EINVAL;
+
+ spi_message_init(&m);
+ memset(t, 0, (sizeof t));
+
+ t[0].tx_buf = flash->command;
+ t[0].len = sizeof(flash->command);
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].rx_buf = buf;
+ t[1].len = len;
+ spi_message_add_tail(&t[1], &m);
+
+ /* Byte count starts at zero. */
+ if (retlen)
+ *retlen = 0;
+
+ down(&flash->lock);
+
+ /* Wait till previous write/erase is done. */
+ if (wait_till_ready(flash)) {
+ /* REVISIT status return?? */
+ up(&flash->lock);
+ return 1;
+ }
+
+ /* NOTE: OPCODE_FAST_READ (if available) is faster... */
+
+ /* Set up the write data buffer. */
+ flash->command[0] = OPCODE_READ;
+ flash->command[1] = from >> 16;
+ flash->command[2] = from >> 8;
+ flash->command[3] = from;
+
+ spi_sync(flash->spi, &m);
+
+ *retlen = m.actual_length - sizeof(flash->command);
+
+ up(&flash->lock);
+
+ return 0;
+}
+
+/*
+ * Write an address range to the flash chip. Data must be written in
+ * FLASH_PAGESIZE chunks. The address range may be any size provided
+ * it is within the physical boundaries.
+ */
+static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t *retlen, const u_char *buf)
+{
+ struct m25p *flash = mtd_to_m25p(mtd);
+ u32 page_offset, page_size;
+ struct spi_transfer t[2];
+ struct spi_message m;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: %s %s 0x%08x, len %zd\n",
+ flash->spi->dev.bus_id, __FUNCTION__, "to",
+ (u32)to, len);
+
+ if (retlen)
+ *retlen = 0;
+
+ /* sanity checks */
+ if (!len)
+ return(0);
+
+ if (to + len > flash->mtd.size)
+ return -EINVAL;
+
+ spi_message_init(&m);
+ memset(t, 0, (sizeof t));
+
+ t[0].tx_buf = flash->command;
+ t[0].len = sizeof(flash->command);
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].tx_buf = buf;
+ spi_message_add_tail(&t[1], &m);
+
+ down(&flash->lock);
+
+ /* Wait until finished previous write command. */
+ if (wait_till_ready(flash))
+ return 1;
+
+ write_enable(flash);
+
+ /* Set up the opcode in the write buffer. */
+ flash->command[0] = OPCODE_PP;
+ flash->command[1] = to >> 16;
+ flash->command[2] = to >> 8;
+ flash->command[3] = to;
+
+ /* what page do we start with? */
+ page_offset = to % FLASH_PAGESIZE;
+
+ /* do all the bytes fit onto one page? */
+ if (page_offset + len <= FLASH_PAGESIZE) {
+ t[1].len = len;
+
+ spi_sync(flash->spi, &m);
+
+ *retlen = m.actual_length - sizeof(flash->command);
+ } else {
+ u32 i;
+
+ /* the size of data remaining on the first page */
+ page_size = FLASH_PAGESIZE - page_offset;
+
+ t[1].len = page_size;
+ spi_sync(flash->spi, &m);
+
+ *retlen = m.actual_length - sizeof(flash->command);
+
+ /* write everything in PAGESIZE chunks */
+ for (i = page_size; i < len; i += page_size) {
+ page_size = len - i;
+ if (page_size > FLASH_PAGESIZE)
+ page_size = FLASH_PAGESIZE;
+
+ /* write the next page to flash */
+ flash->command[1] = (to + i) >> 16;
+ flash->command[2] = (to + i) >> 8;
+ flash->command[3] = (to + i);
+
+ t[1].tx_buf = buf + i;
+ t[1].len = page_size;
+
+ wait_till_ready(flash);
+
+ write_enable(flash);
+
+ spi_sync(flash->spi, &m);
+
+ if (retlen)
+ *retlen += m.actual_length
+ - sizeof(flash->command);
+ }
+ }
+
+ up(&flash->lock);
+
+ return 0;
+}
+
+
+/****************************************************************************/
+
+/*
+ * SPI device driver setup and teardown
+ */
+
+struct flash_info {
+ char *name;
+ u8 id;
+ u16 jedec_id;
+ unsigned sector_size;
+ unsigned n_sectors;
+};
+
+static struct flash_info __devinitdata m25p_data [] = {
+ /* REVISIT: fill in JEDEC ids, for parts that have them */
+ { "m25p05", 0x05, 0x0000, 32 * 1024, 2 },
+ { "m25p10", 0x10, 0x0000, 32 * 1024, 4 },
+ { "m25p20", 0x11, 0x0000, 64 * 1024, 4 },
+ { "m25p40", 0x12, 0x0000, 64 * 1024, 8 },
+ { "m25p80", 0x13, 0x0000, 64 * 1024, 16 },
+ { "m25p16", 0x14, 0x0000, 64 * 1024, 32 },
+ { "m25p32", 0x15, 0x0000, 64 * 1024, 64 },
+ { "m25p64", 0x16, 0x2017, 64 * 1024, 128 },
+};
+
+/*
+ * board specific setup should have ensured the SPI clock used here
+ * matches what the READ command supports, at least until this driver
+ * understands FAST_READ (for clocks over 25 MHz).
+ */
+static int __devinit m25p_probe(struct spi_device *spi)
+{
+ struct flash_platform_data *data;
+ struct m25p *flash;
+ struct flash_info *info;
+ unsigned i;
+
+ /* Platform data helps sort out which chip type we have, as
+ * well as how this board partitions it.
+ */
+ data = spi->dev.platform_data;
+ if (!data || !data->type) {
+ /* FIXME some chips can identify themselves with RES
+ * or JEDEC get-id commands. Try them ...
+ */
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: no chip id\n",
+ flash->spi->dev.bus_id);
+ return -ENODEV;
+ }
+
+ for (i = 0, info = m25p_data; i < ARRAY_SIZE(m25p_data); i++, info++) {
+ if (strcmp(data->type, info->name) == 0)
+ break;
+ }
+ if (i == ARRAY_SIZE(m25p_data)) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: unrecognized id %s\n",
+ flash->spi->dev.bus_id, data->type);
+ return -ENODEV;
+ }
+
+ flash = kzalloc(sizeof *flash, SLAB_KERNEL);
+ if (!flash)
+ return -ENOMEM;
+
+ flash->spi = spi;
+ init_MUTEX(&flash->lock);
+ dev_set_drvdata(&spi->dev, flash);
+
+ if (data->name)
+ flash->mtd.name = data->name;
+ else
+ flash->mtd.name = spi->dev.bus_id;
+
+ flash->mtd.type = MTD_NORFLASH;
+ flash->mtd.flags = MTD_CAP_NORFLASH;
+ flash->mtd.size = info->sector_size * info->n_sectors;
+ flash->mtd.erasesize = info->sector_size;
+ flash->mtd.erase = m25p80_erase;
+ flash->mtd.read = m25p80_read;
+ flash->mtd.write = m25p80_write;
+
+ dev_info(&spi->dev, "%s (%d Kbytes)\n", info->name,
+ flash->mtd.size / 1024);
+
+ DEBUG(MTD_DEBUG_LEVEL2,
+ "mtd .name = %s, .size = 0x%.8x (%uM) "
+ ".erasesize = 0x%.8x (%uK) .numeraseregions = %d\n",
+ flash->mtd.name,
+ flash->mtd.size, flash->mtd.size / (1024*1024),
+ flash->mtd.erasesize, flash->mtd.erasesize / 1024,
+ flash->mtd.numeraseregions);
+
+ if (flash->mtd.numeraseregions)
+ for (i = 0; i < flash->mtd.numeraseregions; i++)
+ DEBUG(MTD_DEBUG_LEVEL2,
+ "mtd.eraseregions[%d] = { .offset = 0x%.8x, "
+ ".erasesize = 0x%.8x (%uK), "
+ ".numblocks = %d }\n",
+ i, flash->mtd.eraseregions[i].offset,
+ flash->mtd.eraseregions[i].erasesize,
+ flash->mtd.eraseregions[i].erasesize / 1024,
+ flash->mtd.eraseregions[i].numblocks);
+
+
+ /* partitions should match sector boundaries; and it may be good to
+ * use readonly partitions for writeprotected sectors (BP2..BP0).
+ */
+ if (mtd_has_partitions()) {
+ struct mtd_partition *parts = NULL;
+ int nr_parts = 0;
+
+#ifdef CONFIG_MTD_CMDLINE_PARTS
+ static const char *part_probes[] = { "cmdlinepart", NULL, };
+
+ nr_parts = parse_mtd_partitions(&flash->mtd,
+ part_probes, &parts, 0);
+#endif
+
+ if (nr_parts <= 0 && data && data->parts) {
+ parts = data->parts;
+ nr_parts = data->nr_parts;
+ }
+
+ if (nr_parts > 0) {
+ for (i = 0; i < data->nr_parts; i++) {
+ DEBUG(MTD_DEBUG_LEVEL2, "partitions[%d] = "
+ "{.name = %s, .offset = 0x%.8x, "
+ ".size = 0x%.8x (%uK) }\n",
+ i, data->parts[i].name,
+ data->parts[i].offset,
+ data->parts[i].size,
+ data->parts[i].size / 1024);
+ }
+ flash->partitioned = 1;
+ return add_mtd_partitions(&flash->mtd, parts, nr_parts);
+ }
+ } else if (data->nr_parts)
+ dev_warn(&spi->dev, "ignoring %d default partitions on %s\n",
+ data->nr_parts, data->name);
+
+ return add_mtd_device(&flash->mtd) == 1 ? -ENODEV : 0;
+}
+
+
+static int __devexit m25p_remove(struct spi_device *spi)
+{
+ struct m25p *flash = dev_get_drvdata(&spi->dev);
+ int status;
+
+ /* Clean up MTD stuff. */
+ if (mtd_has_partitions() && flash->partitioned)
+ status = del_mtd_partitions(&flash->mtd);
+ else
+ status = del_mtd_device(&flash->mtd);
+ if (status == 0)
+ kfree(flash);
+ return 0;
+}
+
+
+static struct spi_driver m25p80_driver = {
+ .driver = {
+ .name = "m25p80",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+ .probe = m25p_probe,
+ .remove = __devexit_p(m25p_remove),
+};
+
+
+static int m25p80_init(void)
+{
+ return spi_register_driver(&m25p80_driver);
+}
+
+
+static void m25p80_exit(void)
+{
+ spi_unregister_driver(&m25p80_driver);
+}
+
+
+module_init(m25p80_init);
+module_exit(m25p80_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Mike Lavender");
+MODULE_DESCRIPTION("MTD SPI driver for ST M25Pxx flash chips");
diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c
new file mode 100644
index 0000000..155737e
--- /dev/null
+++ b/drivers/mtd/devices/mtd_dataflash.c
@@ -0,0 +1,629 @@
+/*
+ * Atmel AT45xxx DataFlash MTD driver for lightweight SPI framework
+ *
+ * Largely derived from at91_dataflash.c:
+ * Copyright (C) 2003-2005 SAN People (Pty) Ltd
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+*/
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+
+/*
+ * DataFlash is a kind of SPI flash. Most AT45 chips have two buffers in
+ * each chip, which may be used for double buffered I/O; but this driver
+ * doesn't (yet) use these for any kind of i/o overlap or prefetching.
+ *
+ * Sometimes DataFlash is packaged in MMC-format cards, although the
+ * MMC stack can't use SPI (yet), or distinguish between MMC and DataFlash
+ * protocols during enumeration.
+ */
+
+#define CONFIG_DATAFLASH_WRITE_VERIFY
+
+/* reads can bypass the buffers */
+#define OP_READ_CONTINUOUS 0xE8
+#define OP_READ_PAGE 0xD2
+
+/* group B requests can run even while status reports "busy" */
+#define OP_READ_STATUS 0xD7 /* group B */
+
+/* move data between host and buffer */
+#define OP_READ_BUFFER1 0xD4 /* group B */
+#define OP_READ_BUFFER2 0xD6 /* group B */
+#define OP_WRITE_BUFFER1 0x84 /* group B */
+#define OP_WRITE_BUFFER2 0x87 /* group B */
+
+/* erasing flash */
+#define OP_ERASE_PAGE 0x81
+#define OP_ERASE_BLOCK 0x50
+
+/* move data between buffer and flash */
+#define OP_TRANSFER_BUF1 0x53
+#define OP_TRANSFER_BUF2 0x55
+#define OP_MREAD_BUFFER1 0xD4
+#define OP_MREAD_BUFFER2 0xD6
+#define OP_MWERASE_BUFFER1 0x83
+#define OP_MWERASE_BUFFER2 0x86
+#define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */
+#define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */
+
+/* write to buffer, then write-erase to flash */
+#define OP_PROGRAM_VIA_BUF1 0x82
+#define OP_PROGRAM_VIA_BUF2 0x85
+
+/* compare buffer to flash */
+#define OP_COMPARE_BUF1 0x60
+#define OP_COMPARE_BUF2 0x61
+
+/* read flash to buffer, then write-erase to flash */
+#define OP_REWRITE_VIA_BUF1 0x58
+#define OP_REWRITE_VIA_BUF2 0x59
+
+/* newer chips report JEDEC manufacturer and device IDs; chip
+ * serial number and OTP bits; and per-sector writeprotect.
+ */
+#define OP_READ_ID 0x9F
+#define OP_READ_SECURITY 0x77
+#define OP_WRITE_SECURITY 0x9A /* OTP bits */
+
+
+struct dataflash {
+ u8 command[4];
+ char name[24];
+
+ unsigned partitioned:1;
+
+ unsigned short page_offset; /* offset in flash address */
+ unsigned int page_size; /* of bytes per page */
+
+ struct semaphore lock;
+ struct spi_device *spi;
+
+ struct mtd_info mtd;
+};
+
+#ifdef CONFIG_MTD_PARTITIONS
+#define mtd_has_partitions() (1)
+#else
+#define mtd_has_partitions() (0)
+#endif
+
+/* ......................................................................... */
+
+/*
+ * Return the status of the DataFlash device.
+ */
+static inline int dataflash_status(struct spi_device *spi)
+{
+ /* NOTE: at45db321c over 25 MHz wants to write
+ * a dummy byte after the opcode...
+ */
+ return spi_w8r8(spi, OP_READ_STATUS);
+}
+
+/*
+ * Poll the DataFlash device until it is READY.
+ * This usually takes 5-20 msec or so; more for sector erase.
+ */
+static int dataflash_waitready(struct spi_device *spi)
+{
+ int status;
+
+ for (;;) {
+ status = dataflash_status(spi);
+ if (status < 0) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: status %d?\n",
+ spi->dev.bus_id, status);
+ status = 0;
+ }
+
+ if (status & (1 << 7)) /* RDY/nBSY */
+ return status;
+
+ msleep(3);
+ }
+}
+
+/* ......................................................................... */
+
+/*
+ * Erase pages of flash.
+ */
+static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr)
+{
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ struct spi_device *spi = priv->spi;
+ struct spi_transfer x = { .tx_dma = 0, };
+ struct spi_message msg;
+ unsigned blocksize = priv->page_size << 3;
+ u8 *command;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: erase addr=0x%x len 0x%x\n",
+ spi->dev.bus_id,
+ instr->addr, instr->len);
+
+ /* Sanity checks */
+ if ((instr->addr + instr->len) > mtd->size
+ || (instr->len % priv->page_size) != 0
+ || (instr->addr % priv->page_size) != 0)
+ return -EINVAL;
+
+ spi_message_init(&msg);
+
+ x.tx_buf = command = priv->command;
+ x.len = 4;
+ spi_message_add_tail(&x, &msg);
+
+ down(&priv->lock);
+ while (instr->len > 0) {
+ unsigned int pageaddr;
+ int status;
+ int do_block;
+
+ /* Calculate flash page address; use block erase (for speed) if
+ * we're at a block boundary and need to erase the whole block.
+ */
+ pageaddr = instr->addr / priv->page_size;
+ do_block = (pageaddr & 0x7) == 0 && instr->len <= blocksize;
+ pageaddr = pageaddr << priv->page_offset;
+
+ command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE;
+ command[1] = (u8)(pageaddr >> 16);
+ command[2] = (u8)(pageaddr >> 8);
+ command[3] = 0;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "ERASE %s: (%x) %x %x %x [%i]\n",
+ do_block ? "block" : "page",
+ command[0], command[1], command[2], command[3],
+ pageaddr);
+
+ status = spi_sync(spi, &msg);
+ (void) dataflash_waitready(spi);
+
+ if (status < 0) {
+ printk(KERN_ERR "%s: erase %x, err %d\n",
+ spi->dev.bus_id, pageaddr, status);
+ /* REVISIT: can retry instr->retries times; or
+ * giveup and instr->fail_addr = instr->addr;
+ */
+ continue;
+ }
+
+ if (do_block) {
+ instr->addr += blocksize;
+ instr->len -= blocksize;
+ } else {
+ instr->addr += priv->page_size;
+ instr->len -= priv->page_size;
+ }
+ }
+ up(&priv->lock);
+
+ /* Inform MTD subsystem that erase is complete */
+ instr->state = MTD_ERASE_DONE;
+ mtd_erase_callback(instr);
+
+ return 0;
+}
+
+/*
+ * Read from the DataFlash device.
+ * from : Start offset in flash device
+ * len : Amount to read
+ * retlen : About of data actually read
+ * buf : Buffer containing the data
+ */
+static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ struct spi_transfer x[2] = { { .tx_dma = 0, }, };
+ struct spi_message msg;
+ unsigned int addr;
+ u8 *command;
+ int status;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: read 0x%x..0x%x\n",
+ priv->spi->dev.bus_id, (unsigned)from, (unsigned)(from + len));
+
+ *retlen = 0;
+
+ /* Sanity checks */
+ if (!len)
+ return 0;
+ if (from + len > mtd->size)
+ return -EINVAL;
+
+ /* Calculate flash page/byte address */
+ addr = (((unsigned)from / priv->page_size) << priv->page_offset)
+ + ((unsigned)from % priv->page_size);
+
+ command = priv->command;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "READ: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ spi_message_init(&msg);
+
+ x[0].tx_buf = command;
+ x[0].len = 8;
+ spi_message_add_tail(&x[0], &msg);
+
+ x[1].rx_buf = buf;
+ x[1].len = len;
+ spi_message_add_tail(&x[1], &msg);
+
+ down(&priv->lock);
+
+ /* Continuous read, max clock = f(car) which may be less than
+ * the peak rate available. Some chips support commands with
+ * fewer "don't care" bytes. Both buffers stay unchanged.
+ */
+ command[0] = OP_READ_CONTINUOUS;
+ command[1] = (u8)(addr >> 16);
+ command[2] = (u8)(addr >> 8);
+ command[3] = (u8)(addr >> 0);
+ /* plus 4 "don't care" bytes */
+
+ status = spi_sync(priv->spi, &msg);
+ up(&priv->lock);
+
+ if (status >= 0) {
+ *retlen = msg.actual_length - 8;
+ status = 0;
+ } else
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: read %x..%x --> %d\n",
+ priv->spi->dev.bus_id,
+ (unsigned)from, (unsigned)(from + len),
+ status);
+ return status;
+}
+
+/*
+ * Write to the DataFlash device.
+ * to : Start offset in flash device
+ * len : Amount to write
+ * retlen : Amount of data actually written
+ * buf : Buffer containing the data
+ */
+static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len,
+ size_t * retlen, const u_char * buf)
+{
+ struct dataflash *priv = (struct dataflash *)mtd->priv;
+ struct spi_device *spi = priv->spi;
+ struct spi_transfer x[2] = { { .tx_dma = 0, }, };
+ struct spi_message msg;
+ unsigned int pageaddr, addr, offset, writelen;
+ size_t remaining = len;
+ u_char *writebuf = (u_char *) buf;
+ int status = -EINVAL;
+ u8 *command;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: write 0x%x..0x%x\n",
+ spi->dev.bus_id, (unsigned)to, (unsigned)(to + len));
+
+ *retlen = 0;
+
+ /* Sanity checks */
+ if (!len)
+ return 0;
+ if ((to + len) > mtd->size)
+ return -EINVAL;
+
+ spi_message_init(&msg);
+
+ x[0].tx_buf = command = priv->command;
+ x[0].len = 4;
+ spi_message_add_tail(&x[0], &msg);
+
+ pageaddr = ((unsigned)to / priv->page_size);
+ offset = ((unsigned)to % priv->page_size);
+ if (offset + len > priv->page_size)
+ writelen = priv->page_size - offset;
+ else
+ writelen = len;
+
+ down(&priv->lock);
+ while (remaining > 0) {
+ DEBUG(MTD_DEBUG_LEVEL3, "write @ %i:%i len=%i\n",
+ pageaddr, offset, writelen);
+
+ /* REVISIT:
+ * (a) each page in a sector must be rewritten at least
+ * once every 10K sibling erase/program operations.
+ * (b) for pages that are already erased, we could
+ * use WRITE+MWRITE not PROGRAM for ~30% speedup.
+ * (c) WRITE to buffer could be done while waiting for
+ * a previous MWRITE/MWERASE to complete ...
+ * (d) error handling here seems to be mostly missing.
+ *
+ * Two persistent bits per page, plus a per-sector counter,
+ * could support (a) and (b) ... we might consider using
+ * the second half of sector zero, which is just one block,
+ * to track that state. (On AT91, that sector should also
+ * support boot-from-DataFlash.)
+ */
+
+ addr = pageaddr << priv->page_offset;
+
+ /* (1) Maybe transfer partial page to Buffer1 */
+ if (writelen != priv->page_size) {
+ command[0] = OP_TRANSFER_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = 0;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "TRANSFER: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ status = spi_sync(spi, &msg);
+ if (status < 0)
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: xfer %u -> %d \n",
+ spi->dev.bus_id, addr, status);
+
+ (void) dataflash_waitready(priv->spi);
+ }
+
+ /* (2) Program full page via Buffer1 */
+ addr += offset;
+ command[0] = OP_PROGRAM_VIA_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = (addr & 0x000000FF);
+
+ DEBUG(MTD_DEBUG_LEVEL3, "PROGRAM: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ x[1].tx_buf = writebuf;
+ x[1].len = writelen;
+ spi_message_add_tail(x + 1, &msg);
+ status = spi_sync(spi, &msg);
+ spi_transfer_del(x + 1);
+ if (status < 0)
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: pgm %u/%u -> %d \n",
+ spi->dev.bus_id, addr, writelen, status);
+
+ (void) dataflash_waitready(priv->spi);
+
+
+#ifdef CONFIG_DATAFLASH_WRITE_VERIFY
+
+ /* (3) Compare to Buffer1 */
+ addr = pageaddr << priv->page_offset;
+ command[0] = OP_COMPARE_BUF1;
+ command[1] = (addr & 0x00FF0000) >> 16;
+ command[2] = (addr & 0x0000FF00) >> 8;
+ command[3] = 0;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "COMPARE: (%x) %x %x %x\n",
+ command[0], command[1], command[2], command[3]);
+
+ status = spi_sync(spi, &msg);
+ if (status < 0)
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: compare %u -> %d \n",
+ spi->dev.bus_id, addr, status);
+
+ status = dataflash_waitready(priv->spi);
+
+ /* Check result of the compare operation */
+ if ((status & (1 << 6)) == 1) {
+ printk(KERN_ERR "%s: compare page %u, err %d\n",
+ spi->dev.bus_id, pageaddr, status);
+ remaining = 0;
+ status = -EIO;
+ break;
+ } else
+ status = 0;
+
+#endif /* CONFIG_DATAFLASH_WRITE_VERIFY */
+
+ remaining = remaining - writelen;
+ pageaddr++;
+ offset = 0;
+ writebuf += writelen;
+ *retlen += writelen;
+
+ if (remaining > priv->page_size)
+ writelen = priv->page_size;
+ else
+ writelen = remaining;
+ }
+ up(&priv->lock);
+
+ return status;
+}
+
+/* ......................................................................... */
+
+/*
+ * Register DataFlash device with MTD subsystem.
+ */
+static int __devinit
+add_dataflash(struct spi_device *spi, char *name,
+ int nr_pages, int pagesize, int pageoffset)
+{
+ struct dataflash *priv;
+ struct mtd_info *device;
+ struct flash_platform_data *pdata = spi->dev.platform_data;
+
+ priv = (struct dataflash *) kzalloc(sizeof *priv, GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ init_MUTEX(&priv->lock);
+ priv->spi = spi;
+ priv->page_size = pagesize;
+ priv->page_offset = pageoffset;
+
+ /* name must be usable with cmdlinepart */
+ sprintf(priv->name, "spi%d.%d-%s",
+ spi->master->bus_num, spi->chip_select,
+ name);
+
+ device = &priv->mtd;
+ device->name = (pdata && pdata->name) ? pdata->name : priv->name;
+ device->size = nr_pages * pagesize;
+ device->erasesize = pagesize;
+ device->owner = THIS_MODULE;
+ device->type = MTD_DATAFLASH;
+ device->flags = MTD_CAP_NORFLASH;
+ device->erase = dataflash_erase;
+ device->read = dataflash_read;
+ device->write = dataflash_write;
+ device->priv = priv;
+
+ dev_info(&spi->dev, "%s (%d KBytes)\n", name, device->size/1024);
+ dev_set_drvdata(&spi->dev, priv);
+
+ if (mtd_has_partitions()) {
+ struct mtd_partition *parts;
+ int nr_parts = 0;
+
+#ifdef CONFIG_MTD_CMDLINE_PARTS
+ static const char *part_probes[] = { "cmdlinepart", NULL, };
+
+ nr_parts = parse_mtd_partitions(device, part_probes, &parts, 0);
+#endif
+
+ if (nr_parts <= 0 && pdata && pdata->parts) {
+ parts = pdata->parts;
+ nr_parts = pdata->nr_parts;
+ }
+
+ if (nr_parts > 0) {
+ priv->partitioned = 1;
+ return add_mtd_partitions(device, parts, nr_parts);
+ }
+ } else if (pdata && pdata->nr_parts)
+ dev_warn(&spi->dev, "ignoring %d default partitions on %s\n",
+ pdata->nr_parts, device->name);
+
+ return add_mtd_device(device) == 1 ? -ENODEV : 0;
+}
+
+/*
+ * Detect and initialize DataFlash device:
+ *
+ * Device Density ID code #Pages PageSize Offset
+ * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9
+ * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1025 264 9
+ * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9
+ * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9
+ * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10
+ * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10
+ * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11
+ * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11
+ */
+static int __devinit dataflash_probe(struct spi_device *spi)
+{
+ int status;
+
+ status = dataflash_status(spi);
+ if (status <= 0 || status == 0xff) {
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: status error %d\n",
+ spi->dev.bus_id, status);
+ if (status == 0xff)
+ status = -ENODEV;
+ return status;
+ }
+
+ /* if there's a device there, assume it's dataflash.
+ * board setup should have set spi->max_speed_max to
+ * match f(car) for continuous reads, mode 0 or 3.
+ */
+ switch (status & 0x3c) {
+ case 0x0c: /* 0 0 1 1 x x */
+ status = add_dataflash(spi, "AT45DB011B", 512, 264, 9);
+ break;
+ case 0x14: /* 0 1 0 1 x x */
+ status = add_dataflash(spi, "AT45DB021B", 1025, 264, 9);
+ break;
+ case 0x1c: /* 0 1 1 1 x x */
+ status = add_dataflash(spi, "AT45DB041x", 2048, 264, 9);
+ break;
+ case 0x24: /* 1 0 0 1 x x */
+ status = add_dataflash(spi, "AT45DB081B", 4096, 264, 9);
+ break;
+ case 0x2c: /* 1 0 1 1 x x */
+ status = add_dataflash(spi, "AT45DB161x", 4096, 528, 10);
+ break;
+ case 0x34: /* 1 1 0 1 x x */
+ status = add_dataflash(spi, "AT45DB321x", 8192, 528, 10);
+ break;
+ case 0x38: /* 1 1 1 x x x */
+ case 0x3c:
+ status = add_dataflash(spi, "AT45DB642x", 8192, 1056, 11);
+ break;
+ /* obsolete AT45DB1282 not (yet?) supported */
+ default:
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: unsupported device (%x)\n",
+ spi->dev.bus_id, status & 0x3c);
+ status = -ENODEV;
+ }
+
+ if (status < 0)
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: add_dataflash --> %d\n",
+ spi->dev.bus_id, status);
+
+ return status;
+}
+
+static int __devexit dataflash_remove(struct spi_device *spi)
+{
+ struct dataflash *flash = dev_get_drvdata(&spi->dev);
+ int status;
+
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: remove\n", spi->dev.bus_id);
+
+ if (mtd_has_partitions() && flash->partitioned)
+ status = del_mtd_partitions(&flash->mtd);
+ else
+ status = del_mtd_device(&flash->mtd);
+ if (status == 0)
+ kfree(flash);
+ return status;
+}
+
+static struct spi_driver dataflash_driver = {
+ .driver = {
+ .name = "mtd_dataflash",
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+
+ .probe = dataflash_probe,
+ .remove = __devexit_p(dataflash_remove),
+
+ /* FIXME: investigate suspend and resume... */
+};
+
+static int __init dataflash_init(void)
+{
+ return spi_register_driver(&dataflash_driver);
+}
+module_init(dataflash_init);
+
+static void __exit dataflash_exit(void)
+{
+ spi_unregister_driver(&dataflash_driver);
+}
+module_exit(dataflash_exit);
+
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andrew Victor, David Brownell");
+MODULE_DESCRIPTION("MTD DataFlash driver");
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
new file mode 100644
index 0000000..b77dbd6
--- /dev/null
+++ b/drivers/spi/Kconfig
@@ -0,0 +1,109 @@
+#
+# SPI driver configuration
+#
+# NOTE: the reason this doesn't show SPI slave support is mostly that
+# nobody's needed a slave side API yet. The master-role API is not
+# fully appropriate there, so it'd need some thought to do well.
+#
+menu "SPI support"
+
+config SPI
+ bool "SPI support"
+ help
+ The "Serial Peripheral Interface" is a low level synchronous
+ protocol. Chips that support SPI can have data transfer rates
+ up to several tens of Mbit/sec. Chips are addressed with a
+ controller and a chipselect. Most SPI slaves don't support
+ dynamic device discovery; some are even write-only or read-only.
+
+ SPI is widely used by microcontollers to talk with sensors,
+ eeprom and flash memory, codecs and various other controller
+ chips, analog to digital (and d-to-a) converters, and more.
+ MMC and SD cards can be accessed using SPI protocol; and for
+ DataFlash cards used in MMC sockets, SPI must always be used.
+
+ SPI is one of a family of similar protocols using a four wire
+ interface (select, clock, data in, data out) including Microwire
+ (half duplex), SSP, SSI, and PSP. This driver framework should
+ work with most such devices and controllers.
+
+config SPI_DEBUG
+ boolean "Debug support for SPI drivers"
+ depends on SPI && DEBUG_KERNEL
+ help
+ Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
+ sysfs, and debugfs support in SPI controller and protocol drivers.
+
+#
+# MASTER side ... talking to discrete SPI slave chips including microcontrollers
+#
+
+config SPI_MASTER
+# boolean "SPI Master Support"
+ boolean
+ default SPI
+ help
+ If your system has an master-capable SPI controller (which
+ provides the clock and chipselect), you can enable that
+ controller and the protocol drivers for the SPI slave chips
+ that are connected.
+
+comment "SPI Master Controller Drivers"
+ depends on SPI_MASTER
+
+config SPI_BITBANG
+ tristate "Bitbanging SPI master"
+ depends on SPI_MASTER && EXPERIMENTAL
+ help
+ With a few GPIO pins, your system can bitbang the SPI protocol.
+ Select this to get SPI support through I/O pins (GPIO, parallel
+ port, etc). Or, some systems' SPI master controller drivers use
+ this code to manage the per-word or per-transfer accesses to the
+ hardware shift registers.
+
+ This is library code, and is automatically selected by drivers that
+ need it. You only need to select this explicitly to support driver
+ modules that aren't part of this kernel tree.
+
+config SPI_BUTTERFLY
+ tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
+ depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This uses a custom parallel port cable to connect to an AVR
+ Butterfly <http://www.atmel.com/products/avr/butterfly>, an
+ inexpensive battery powered microcontroller evaluation board.
+ This same cable can be used to flash new firmware.
+
+config SPI_BUTTERFLY
+ tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
+ depends on SPI_MASTER && PARPORT && EXPERIMENTAL
+ select SPI_BITBANG
+ help
+ This uses a custom parallel port cable to connect to an AVR
+ Butterfly <http://www.atmel.com/products/avr/butterfly>, an
+ inexpensive battery powered microcontroller evaluation board.
+ This same cable can be used to flash new firmware.
+
+#
+# Add new SPI master controllers in alphabetical order above this line
+#
+
+
+#
+# There are lots of SPI device types, with sensors and memory
+# being probably the most widely used ones.
+#
+comment "SPI Protocol Masters"
+ depends on SPI_MASTER
+
+
+#
+# Add new SPI protocol masters in alphabetical order above this line
+#
+
+
+# (slave support would go here)
+
+endmenu # "SPI support"
+
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
new file mode 100644
index 0000000..c2c87e8
--- /dev/null
+++ b/drivers/spi/Makefile
@@ -0,0 +1,25 @@
+#
+# Makefile for kernel SPI drivers.
+#
+
+ifeq ($(CONFIG_SPI_DEBUG),y)
+EXTRA_CFLAGS += -DDEBUG
+endif
+
+# small core, mostly translating board-specific
+# config declarations into driver model code
+obj-$(CONFIG_SPI_MASTER) += spi.o
+
+# SPI master controller drivers (bus)
+obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
+obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
+# ... add above this line ...
+
+# SPI protocol drivers (device/link on bus)
+# ... add above this line ...
+
+# SPI slave controller drivers (upstream link)
+# ... add above this line ...
+
+# SPI slave drivers (protocol for that link)
+# ... add above this line ...
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
new file mode 100644
index 0000000..791c4dc
--- /dev/null
+++ b/drivers/spi/spi.c
@@ -0,0 +1,642 @@
+/*
+ * spi.c - SPI init/core code
+ *
+ * Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/autoconf.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/cache.h>
+#include <linux/spi/spi.h>
+
+
+/* SPI bustype and spi_master class are registered after board init code
+ * provides the SPI device tables, ensuring that both are present by the
+ * time controller driver registration causes spi_devices to "enumerate".
+ */
+static void spidev_release(struct device *dev)
+{
+ const struct spi_device *spi = to_spi_device(dev);
+
+ /* spi masters may cleanup for released devices */
+ if (spi->master->cleanup)
+ spi->master->cleanup(spi);
+
+ spi_master_put(spi->master);
+ kfree(dev);
+}
+
+static ssize_t
+modalias_show(struct device *dev, struct device_attribute *a, char *buf)
+{
+ const struct spi_device *spi = to_spi_device(dev);
+
+ return snprintf(buf, BUS_ID_SIZE + 1, "%s\n", spi->modalias);
+}
+
+static struct device_attribute spi_dev_attrs[] = {
+ __ATTR_RO(modalias),
+ __ATTR_NULL,
+};
+
+/* modalias support makes "modprobe $MODALIAS" new-style hotplug work,
+ * and the sysfs version makes coldplug work too.
+ */
+
+static int spi_match_device(struct device *dev, struct device_driver *drv)
+{
+ const struct spi_device *spi = to_spi_device(dev);
+
+ return strncmp(spi->modalias, drv->name, BUS_ID_SIZE) == 0;
+}
+
+static int spi_uevent(struct device *dev, char **envp, int num_envp,
+ char *buffer, int buffer_size)
+{
+ const struct spi_device *spi = to_spi_device(dev);
+
+ envp[0] = buffer;
+ snprintf(buffer, buffer_size, "MODALIAS=%s", spi->modalias);
+ envp[1] = NULL;
+ return 0;
+}
+
+#ifdef CONFIG_PM
+
+/*
+ * NOTE: the suspend() method for an spi_master controller driver
+ * should verify that all its child devices are marked as suspended;
+ * suspend requests delivered through sysfs power/state files don't
+ * enforce such constraints.
+ */
+static int spi_suspend(struct device *dev, pm_message_t message)
+{
+ int value;
+ struct spi_driver *drv = to_spi_driver(dev->driver);
+
+ if (!drv->suspend)
+ return 0;
+
+ /* suspend will stop irqs and dma; no more i/o */
+ value = drv->suspend(to_spi_device(dev), message);
+ if (value == 0)
+ dev->power.power_state = message;
+ return value;
+}
+
+static int spi_resume(struct device *dev)
+{
+ int value;
+ struct spi_driver *drv = to_spi_driver(dev->driver);
+
+ if (!drv->resume)
+ return 0;
+
+ /* resume may restart the i/o queue */
+ value = drv->resume(to_spi_device(dev));
+ if (value == 0)
+ dev->power.power_state = PMSG_ON;
+ return value;
+}
+
+#else
+#define spi_suspend NULL
+#define spi_resume NULL
+#endif
+
+struct bus_type spi_bus_type = {
+ .name = "spi",
+ .dev_attrs = spi_dev_attrs,
+ .match = spi_match_device,
+ .uevent = spi_uevent,
+ .suspend = spi_suspend,
+ .resume = spi_resume,
+};
+EXPORT_SYMBOL_GPL(spi_bus_type);
+
+
+static int spi_drv_probe(struct device *dev)
+{
+ const struct spi_driver *sdrv = to_spi_driver(dev->driver);
+
+ return sdrv->probe(to_spi_device(dev));
+}
+
+static int spi_drv_remove(struct device *dev)
+{
+ const struct spi_driver *sdrv = to_spi_driver(dev->driver);
+
+ return sdrv->remove(to_spi_device(dev));
+}
+
+static void spi_drv_shutdown(struct device *dev)
+{
+ const struct spi_driver *sdrv = to_spi_driver(dev->driver);
+
+ sdrv->shutdown(to_spi_device(dev));
+}
+
+int spi_register_driver(struct spi_driver *sdrv)
+{
+ sdrv->driver.bus = &spi_bus_type;
+ if (sdrv->probe)
+ sdrv->driver.probe = spi_drv_probe;
+ if (sdrv->remove)
+ sdrv->driver.remove = spi_drv_remove;
+ if (sdrv->shutdown)
+ sdrv->driver.shutdown = spi_drv_shutdown;
+ return driver_register(&sdrv->driver);
+}
+EXPORT_SYMBOL_GPL(spi_register_driver);
+
+/*-------------------------------------------------------------------------*/
+
+/* SPI devices should normally not be created by SPI device drivers; that
+ * would make them board-specific. Similarly with SPI master drivers.
+ * Device registration normally goes into like arch/.../mach.../board-YYY.c
+ * with other readonly (flashable) information about mainboard devices.
+ */
+
+struct boardinfo {
+ struct list_head list;
+ unsigned n_board_info;
+ struct spi_board_info board_info[0];
+};
+
+static LIST_HEAD(board_list);
+static DECLARE_MUTEX(board_lock);
+
+
+/* On typical mainboards, this is purely internal; and it's not needed
+ * after board init creates the hard-wired devices. Some development
+ * platforms may not be able to use spi_register_board_info though, and
+ * this is exported so that for example a USB or parport based adapter
+ * driver could add devices (which it would learn about out-of-band).
+ */
+struct spi_device *__init_or_module
+spi_new_device(struct spi_master *master, struct spi_board_info *chip)
+{
+ struct spi_device *proxy;
+ struct device *dev = master->cdev.dev;
+ int status;
+
+ /* NOTE: caller did any chip->bus_num checks necessary */
+
+ if (!spi_master_get(master))
+ return NULL;
+
+ proxy = kzalloc(sizeof *proxy, GFP_KERNEL);
+ if (!proxy) {
+ dev_err(dev, "can't alloc dev for cs%d\n",
+ chip->chip_select);
+ goto fail;
+ }
+ proxy->master = master;
+ proxy->chip_select = chip->chip_select;
+ proxy->max_speed_hz = chip->max_speed_hz;
+ proxy->irq = chip->irq;
+ proxy->modalias = chip->modalias;
+
+ snprintf(proxy->dev.bus_id, sizeof proxy->dev.bus_id,
+ "%s.%u", master->cdev.class_id,
+ chip->chip_select);
+ proxy->dev.parent = dev;
+ proxy->dev.bus = &spi_bus_type;
+ proxy->dev.platform_data = (void *) chip->platform_data;
+ proxy->controller_data = chip->controller_data;
+ proxy->controller_state = NULL;
+ proxy->dev.release = spidev_release;
+
+ /* drivers may modify this default i/o setup */
+ status = master->setup(proxy);
+ if (status < 0) {
+ dev_dbg(dev, "can't %s %s, status %d\n",
+ "setup", proxy->dev.bus_id, status);
+ goto fail;
+ }
+
+ /* driver core catches callers that misbehave by defining
+ * devices that already exist.
+ */
+ status = device_register(&proxy->dev);
+ if (status < 0) {
+ dev_dbg(dev, "can't %s %s, status %d\n",
+ "add", proxy->dev.bus_id, status);
+ goto fail;
+ }
+ dev_dbg(dev, "registered child %s\n", proxy->dev.bus_id);
+ return proxy;
+
+fail:
+ spi_master_put(master);
+ kfree(proxy);
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(spi_new_device);
+
+/*
+ * Board-specific early init code calls this (probably during arch_initcall)
+ * with segments of the SPI device table. Any device nodes are created later,
+ * after the relevant parent SPI controller (bus_num) is defined. We keep
+ * this table of devices forever, so that reloading a controller driver will
+ * not make Linux forget about these hard-wired devices.
+ *
+ * Other code can also call this, e.g. a particular add-on board might provide
+ * SPI devices through its expansion connector, so code initializing that board
+ * would naturally declare its SPI devices.
+ *
+ * The board info passed can safely be __initdata ... but be careful of
+ * any embedded pointers (platform_data, etc), they're copied as-is.
+ */
+int __init
+spi_register_board_info(struct spi_board_info const *info, unsigned n)
+{
+ struct boardinfo *bi;
+
+ bi = kmalloc(sizeof(*bi) + n * sizeof *info, GFP_KERNEL);
+ if (!bi)
+ return -ENOMEM;
+ bi->n_board_info = n;
+ memcpy(bi->board_info, info, n * sizeof *info);
+
+ down(&board_lock);
+ list_add_tail(&bi->list, &board_list);
+ up(&board_lock);
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_register_board_info);
+
+/* FIXME someone should add support for a __setup("spi", ...) that
+ * creates board info from kernel command lines
+ */
+
+static void __init_or_module
+scan_boardinfo(struct spi_master *master)
+{
+ struct boardinfo *bi;
+ struct device *dev = master->cdev.dev;
+
+ down(&board_lock);
+ list_for_each_entry(bi, &board_list, list) {
+ struct spi_board_info *chip = bi->board_info;
+ unsigned n;
+
+ for (n = bi->n_board_info; n > 0; n--, chip++) {
+ if (chip->bus_num != master->bus_num)
+ continue;
+ /* some controllers only have one chip, so they
+ * might not use chipselects. otherwise, the
+ * chipselects are numbered 0..max.
+ */
+ if (chip->chip_select >= master->num_chipselect
+ && master->num_chipselect) {
+ dev_dbg(dev, "cs%d > max %d\n",
+ chip->chip_select,
+ master->num_chipselect);
+ continue;
+ }
+ (void) spi_new_device(master, chip);
+ }
+ }
+ up(&board_lock);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static void spi_master_release(struct class_device *cdev)
+{
+ struct spi_master *master;
+
+ master = container_of(cdev, struct spi_master, cdev);
+ kfree(master);
+}
+
+static struct class spi_master_class = {
+ .name = "spi_master",
+ .owner = THIS_MODULE,
+ .release = spi_master_release,
+};
+
+
+/**
+ * spi_alloc_master - allocate SPI master controller
+ * @dev: the controller, possibly using the platform_bus
+ * @size: how much driver-private data to preallocate; the pointer to this
+ * memory is in the class_data field of the returned class_device,
+ * accessible with spi_master_get_devdata().
+ *
+ * This call is used only by SPI master controller drivers, which are the
+ * only ones directly touching chip registers. It's how they allocate
+ * an spi_master structure, prior to calling spi_add_master().
+ *
+ * This must be called from context that can sleep. It returns the SPI
+ * master structure on success, else NULL.
+ *
+ * The caller is responsible for assigning the bus number and initializing
+ * the master's methods before calling spi_add_master(); and (after errors
+ * adding the device) calling spi_master_put() to prevent a memory leak.
+ */
+struct spi_master * __init_or_module
+spi_alloc_master(struct device *dev, unsigned size)
+{
+ struct spi_master *master;
+
+ if (!dev)
+ return NULL;
+
+ master = kzalloc(size + sizeof *master, SLAB_KERNEL);
+ if (!master)
+ return NULL;
+
+ class_device_initialize(&master->cdev);
+ master->cdev.class = &spi_master_class;
+ master->cdev.dev = get_device(dev);
+ spi_master_set_devdata(master, &master[1]);
+
+ return master;
+}
+EXPORT_SYMBOL_GPL(spi_alloc_master);
+
+/**
+ * spi_register_master - register SPI master controller
+ * @master: initialized master, originally from spi_alloc_master()
+ *
+ * SPI master controllers connect to their drivers using some non-SPI bus,
+ * such as the platform bus. The final stage of probe() in that code
+ * includes calling spi_register_master() to hook up to this SPI bus glue.
+ *
+ * SPI controllers use board specific (often SOC specific) bus numbers,
+ * and board-specific addressing for SPI devices combines those numbers
+ * with chip select numbers. Since SPI does not directly support dynamic
+ * device identification, boards need configuration tables telling which
+ * chip is at which address.
+ *
+ * This must be called from context that can sleep. It returns zero on
+ * success, else a negative error code (dropping the master's refcount).
+ * After a successful return, the caller is responsible for calling
+ * spi_unregister_master().
+ */
+int __init_or_module
+spi_register_master(struct spi_master *master)
+{
+ static atomic_t dyn_bus_id = ATOMIC_INIT(0);
+ struct device *dev = master->cdev.dev;
+ int status = -ENODEV;
+ int dynamic = 0;
+
+ if (!dev)
+ return -ENODEV;
+
+ /* convention: dynamically assigned bus IDs count down from the max */
+ if (master->bus_num == 0) {
+ master->bus_num = atomic_dec_return(&dyn_bus_id);
+ dynamic = 1;
+ }
+
+ /* register the device, then userspace will see it.
+ * registration fails if the bus ID is in use.
+ */
+ snprintf(master->cdev.class_id, sizeof master->cdev.class_id,
+ "spi%u", master->bus_num);
+ status = class_device_add(&master->cdev);
+ if (status < 0)
+ goto done;
+ dev_dbg(dev, "registered master %s%s\n", master->cdev.class_id,
+ dynamic ? " (dynamic)" : "");
+
+ /* populate children from any spi device tables */
+ scan_boardinfo(master);
+ status = 0;
+done:
+ return status;
+}
+EXPORT_SYMBOL_GPL(spi_register_master);
+
+
+static int __unregister(struct device *dev, void *unused)
+{
+ /* note: before about 2.6.14-rc1 this would corrupt memory: */
+ spi_unregister_device(to_spi_device(dev));
+ return 0;
+}
+
+/**
+ * spi_unregister_master - unregister SPI master controller
+ * @master: the master being unregistered
+ *
+ * This call is used only by SPI master controller drivers, which are the
+ * only ones directly touching chip registers.
+ *
+ * This must be called from context that can sleep.
+ */
+void spi_unregister_master(struct spi_master *master)
+{
+ (void) device_for_each_child(master->cdev.dev, NULL, __unregister);
+ class_device_unregister(&master->cdev);
+ master->cdev.dev = NULL;
+}
+EXPORT_SYMBOL_GPL(spi_unregister_master);
+
+/**
+ * spi_busnum_to_master - look up master associated with bus_num
+ * @bus_num: the master's bus number
+ *
+ * This call may be used with devices that are registered after
+ * arch init time. It returns a refcounted pointer to the relevant
+ * spi_master (which the caller must release), or NULL if there is
+ * no such master registered.
+ */
+struct spi_master *spi_busnum_to_master(u16 bus_num)
+{
+ if (bus_num) {
+ char name[8];
+ struct kobject *bus;
+
+ snprintf(name, sizeof name, "spi%u", bus_num);
+ bus = kset_find_obj(&spi_master_class.subsys.kset, name);
+ if (bus)
+ return container_of(bus, struct spi_master, cdev.kobj);
+ }
+ return NULL;
+}
+EXPORT_SYMBOL_GPL(spi_busnum_to_master);
+
+
+/*-------------------------------------------------------------------------*/
+
+static void spi_complete(void *arg)
+{
+ complete(arg);
+}
+
+/**
+ * spi_sync - blocking/synchronous SPI data transfers
+ * @spi: device with which data will be exchanged
+ * @message: describes the data transfers
+ *
+ * This call may only be used from a context that may sleep. The sleep
+ * is non-interruptible, and has no timeout. Low-overhead controller
+ * drivers may DMA directly into and out of the message buffers.
+ *
+ * Note that the SPI device's chip select is active during the message,
+ * and then is normally disabled between messages. Drivers for some
+ * frequently-used devices may want to minimize costs of selecting a chip,
+ * by leaving it selected in anticipation that the next message will go
+ * to the same chip. (That may increase power usage.)
+ *
+ * Also, the caller is guaranteeing that the memory associated with the
+ * message will not be freed before this call returns.
+ *
+ * The return value is a negative error code if the message could not be
+ * submitted, else zero. When the value is zero, then message->status is
+ * also defined: it's the completion code for the transfer, either zero
+ * or a negative error code from the controller driver.
+ */
+int spi_sync(struct spi_device *spi, struct spi_message *message)
+{
+ DECLARE_COMPLETION(done);
+ int status;
+
+ message->complete = spi_complete;
+ message->context = &done;
+ status = spi_async(spi, message);
+ if (status == 0)
+ wait_for_completion(&done);
+ message->context = NULL;
+ return status;
+}
+EXPORT_SYMBOL_GPL(spi_sync);
+
+#define SPI_BUFSIZ (SMP_CACHE_BYTES)
+
+static u8 *buf;
+
+/**
+ * spi_write_then_read - SPI synchronous write followed by read
+ * @spi: device with which data will be exchanged
+ * @txbuf: data to be written (need not be dma-safe)
+ * @n_tx: size of txbuf, in bytes
+ * @rxbuf: buffer into which data will be read
+ * @n_rx: size of rxbuf, in bytes (need not be dma-safe)
+ *
+ * This performs a half duplex MicroWire style transaction with the
+ * device, sending txbuf and then reading rxbuf. The return value
+ * is zero for success, else a negative errno status code.
+ * This call may only be used from a context that may sleep.
+ *
+ * Parameters to this routine are always copied using a small buffer;
+ * performance-sensitive or bulk transfer code should instead use
+ * spi_{async,sync}() calls with dma-safe buffers.
+ */
+int spi_write_then_read(struct spi_device *spi,
+ const u8 *txbuf, unsigned n_tx,
+ u8 *rxbuf, unsigned n_rx)
+{
+ static DECLARE_MUTEX(lock);
+
+ int status;
+ struct spi_message message;
+ struct spi_transfer x[2];
+ u8 *local_buf;
+
+ /* Use preallocated DMA-safe buffer. We can't avoid copying here,
+ * (as a pure convenience thing), but we can keep heap costs
+ * out of the hot path ...
+ */
+ if ((n_tx + n_rx) > SPI_BUFSIZ)
+ return -EINVAL;
+
+ spi_message_init(&message);
+ memset(x, 0, sizeof x);
+ if (n_tx) {
+ x[0].len = n_tx;
+ spi_message_add_tail(&x[0], &message);
+ }
+ if (n_rx) {
+ x[1].len = n_rx;
+ spi_message_add_tail(&x[1], &message);
+ }
+
+ /* ... unless someone else is using the pre-allocated buffer */
+ if (down_trylock(&lock)) {
+ local_buf = kmalloc(SPI_BUFSIZ, GFP_KERNEL);
+ if (!local_buf)
+ return -ENOMEM;
+ } else
+ local_buf = buf;
+
+ memcpy(local_buf, txbuf, n_tx);
+ x[0].tx_buf = local_buf;
+ x[1].rx_buf = local_buf + n_tx;
+
+ /* do the i/o */
+ status = spi_sync(spi, &message);
+ if (status == 0) {
+ memcpy(rxbuf, x[1].rx_buf, n_rx);
+ status = message.status;
+ }
+
+ if (x[0].tx_buf == buf)
+ up(&lock);
+ else
+ kfree(local_buf);
+
+ return status;
+}
+EXPORT_SYMBOL_GPL(spi_write_then_read);
+
+/*-------------------------------------------------------------------------*/
+
+static int __init spi_init(void)
+{
+ int status;
+
+ buf = kmalloc(SPI_BUFSIZ, SLAB_KERNEL);
+ if (!buf) {
+ status = -ENOMEM;
+ goto err0;
+ }
+
+ status = bus_register(&spi_bus_type);
+ if (status < 0)
+ goto err1;
+
+ status = class_register(&spi_master_class);
+ if (status < 0)
+ goto err2;
+ return 0;
+
+err2:
+ bus_unregister(&spi_bus_type);
+err1:
+ kfree(buf);
+ buf = NULL;
+err0:
+ return status;
+}
+
+/* board_info is normally registered in arch_initcall(),
+ * but even essential drivers wait till later
+ *
+ * REVISIT only boardinfo really needs static linking. the rest (device and
+ * driver registration) _could_ be dynamically linked (modular) ... costs
+ * include needing to have boardinfo data structures be much more public.
+ */
+subsys_initcall(spi_init);
+
diff --git a/drivers/spi/spi_bitbang.c b/drivers/spi/spi_bitbang.c
new file mode 100644
index 0000000..f037e55
--- /dev/null
+++ b/drivers/spi/spi_bitbang.c
@@ -0,0 +1,472 @@
+/*
+ * spi_bitbang.c - polling/bitbanging SPI master controller driver utilities
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/platform_device.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * FIRST PART (OPTIONAL): word-at-a-time spi_transfer support.
+ * Use this for GPIO or shift-register level hardware APIs.
+ *
+ * spi_bitbang_cs is in spi_device->controller_state, which is unavailable
+ * to glue code. These bitbang setup() and cleanup() routines are always
+ * used, though maybe they're called from controller-aware code.
+ *
+ * chipselect() and friends may use use spi_device->controller_data and
+ * controller registers as appropriate.
+ *
+ *
+ * NOTE: SPI controller pins can often be used as GPIO pins instead,
+ * which means you could use a bitbang driver either to get hardware
+ * working quickly, or testing for differences that aren't speed related.
+ */
+
+struct spi_bitbang_cs {
+ unsigned nsecs; /* (clock cycle time)/2 */
+ u32 (*txrx_word)(struct spi_device *spi, unsigned nsecs,
+ u32 word, u8 bits);
+ unsigned (*txrx_bufs)(struct spi_device *,
+ u32 (*txrx_word)(
+ struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits),
+ unsigned, struct spi_transfer *);
+};
+
+static unsigned bitbang_txrx_8(
+ struct spi_device *spi,
+ u32 (*txrx_word)(struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits),
+ unsigned ns,
+ struct spi_transfer *t
+) {
+ unsigned bits = spi->bits_per_word;
+ unsigned count = t->len;
+ const u8 *tx = t->tx_buf;
+ u8 *rx = t->rx_buf;
+
+ while (likely(count > 0)) {
+ u8 word = 0;
+
+ if (tx)
+ word = *tx++;
+ word = txrx_word(spi, ns, word, bits);
+ if (rx)
+ *rx++ = word;
+ count -= 1;
+ }
+ return t->len - count;
+}
+
+static unsigned bitbang_txrx_16(
+ struct spi_device *spi,
+ u32 (*txrx_word)(struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits),
+ unsigned ns,
+ struct spi_transfer *t
+) {
+ unsigned bits = spi->bits_per_word;
+ unsigned count = t->len;
+ const u16 *tx = t->tx_buf;
+ u16 *rx = t->rx_buf;
+
+ while (likely(count > 1)) {
+ u16 word = 0;
+
+ if (tx)
+ word = *tx++;
+ word = txrx_word(spi, ns, word, bits);
+ if (rx)
+ *rx++ = word;
+ count -= 2;
+ }
+ return t->len - count;
+}
+
+static unsigned bitbang_txrx_32(
+ struct spi_device *spi,
+ u32 (*txrx_word)(struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits),
+ unsigned ns,
+ struct spi_transfer *t
+) {
+ unsigned bits = spi->bits_per_word;
+ unsigned count = t->len;
+ const u32 *tx = t->tx_buf;
+ u32 *rx = t->rx_buf;
+
+ while (likely(count > 3)) {
+ u32 word = 0;
+
+ if (tx)
+ word = *tx++;
+ word = txrx_word(spi, ns, word, bits);
+ if (rx)
+ *rx++ = word;
+ count -= 4;
+ }
+ return t->len - count;
+}
+
+/**
+ * spi_bitbang_setup - default setup for per-word I/O loops
+ */
+int spi_bitbang_setup(struct spi_device *spi)
+{
+ struct spi_bitbang_cs *cs = spi->controller_state;
+ struct spi_bitbang *bitbang;
+
+ if (!spi->max_speed_hz)
+ return -EINVAL;
+
+ if (!cs) {
+ cs = kzalloc(sizeof *cs, SLAB_KERNEL);
+ if (!cs)
+ return -ENOMEM;
+ spi->controller_state = cs;
+ }
+ bitbang = spi_master_get_devdata(spi->master);
+
+ if (!spi->bits_per_word)
+ spi->bits_per_word = 8;
+
+ /* spi_transfer level calls that work per-word */
+ if (spi->bits_per_word <= 8)
+ cs->txrx_bufs = bitbang_txrx_8;
+ else if (spi->bits_per_word <= 16)
+ cs->txrx_bufs = bitbang_txrx_16;
+ else if (spi->bits_per_word <= 32)
+ cs->txrx_bufs = bitbang_txrx_32;
+ else
+ return -EINVAL;
+
+ /* per-word shift register access, in hardware or bitbanging */
+ cs->txrx_word = bitbang->txrx_word[spi->mode & (SPI_CPOL|SPI_CPHA)];
+ if (!cs->txrx_word)
+ return -EINVAL;
+
+ /* nsecs = (clock period)/2 */
+ cs->nsecs = (1000000000/2) / (spi->max_speed_hz);
+ if (cs->nsecs > MAX_UDELAY_MS * 1000)
+ return -EINVAL;
+
+ dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec\n",
+ __FUNCTION__, spi->mode & (SPI_CPOL | SPI_CPHA),
+ spi->bits_per_word, 2 * cs->nsecs);
+
+ /* NOTE we _need_ to call chipselect() early, ideally with adapter
+ * setup, unless the hardware defaults cooperate to avoid confusion
+ * between normal (active low) and inverted chipselects.
+ */
+
+ /* deselect chip (low or high) */
+ spin_lock(&bitbang->lock);
+ if (!bitbang->busy) {
+ bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
+ ndelay(cs->nsecs);
+ }
+ spin_unlock(&bitbang->lock);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_setup);
+
+/**
+ * spi_bitbang_cleanup - default cleanup for per-word I/O loops
+ */
+void spi_bitbang_cleanup(const struct spi_device *spi)
+{
+ kfree(spi->controller_state);
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_cleanup);
+
+static int spi_bitbang_bufs(struct spi_device *spi, struct spi_transfer *t)
+{
+ struct spi_bitbang_cs *cs = spi->controller_state;
+ unsigned nsecs = cs->nsecs;
+
+ return cs->txrx_bufs(spi, cs->txrx_word, nsecs, t);
+}
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * SECOND PART ... simple transfer queue runner.
+ *
+ * This costs a task context per controller, running the queue by
+ * performing each transfer in sequence. Smarter hardware can queue
+ * several DMA transfers at once, and process several controller queues
+ * in parallel; this driver doesn't match such hardware very well.
+ *
+ * Drivers can provide word-at-a-time i/o primitives, or provide
+ * transfer-at-a-time ones to leverage dma or fifo hardware.
+ */
+static void bitbang_work(void *_bitbang)
+{
+ struct spi_bitbang *bitbang = _bitbang;
+ unsigned long flags;
+
+ spin_lock_irqsave(&bitbang->lock, flags);
+ bitbang->busy = 1;
+ while (!list_empty(&bitbang->queue)) {
+ struct spi_message *m;
+ struct spi_device *spi;
+ unsigned nsecs;
+ struct spi_transfer *t = NULL;
+ unsigned tmp;
+ unsigned cs_change;
+ int status;
+
+ m = container_of(bitbang->queue.next, struct spi_message,
+ queue);
+ list_del_init(&m->queue);
+ spin_unlock_irqrestore(&bitbang->lock, flags);
+
+ /* FIXME this is made-up ... the correct value is known to
+ * word-at-a-time bitbang code, and presumably chipselect()
+ * should enforce these requirements too?
+ */
+ nsecs = 100;
+
+ spi = m->spi;
+ tmp = 0;
+ cs_change = 1;
+ status = 0;
+
+ list_for_each_entry (t, &m->transfers, transfer_list) {
+ if (bitbang->shutdown) {
+ status = -ESHUTDOWN;
+ break;
+ }
+
+ /* set up default clock polarity, and activate chip;
+ * this implicitly updates clock and spi modes as
+ * previously recorded for this device via setup().
+ * (and also deselects any other chip that might be
+ * selected ...)
+ */
+ if (cs_change) {
+ bitbang->chipselect(spi, BITBANG_CS_ACTIVE);
+ ndelay(nsecs);
+ }
+ cs_change = t->cs_change;
+ if (!t->tx_buf && !t->rx_buf && t->len) {
+ status = -EINVAL;
+ break;
+ }
+
+ /* transfer data. the lower level code handles any
+ * new dma mappings it needs. our caller always gave
+ * us dma-safe buffers.
+ */
+ if (t->len) {
+ /* REVISIT dma API still needs a designated
+ * DMA_ADDR_INVALID; ~0 might be better.
+ */
+ if (!m->is_dma_mapped)
+ t->rx_dma = t->tx_dma = 0;
+ status = bitbang->txrx_bufs(spi, t);
+ }
+ if (status != t->len) {
+ if (status > 0)
+ status = -EMSGSIZE;
+ break;
+ }
+ m->actual_length += status;
+ status = 0;
+
+ /* protocol tweaks before next transfer */
+ if (t->delay_usecs)
+ udelay(t->delay_usecs);
+
+ if (!cs_change)
+ continue;
+ if (t->transfer_list.next == &m->transfers)
+ break;
+
+ /* sometimes a short mid-message deselect of the chip
+ * may be needed to terminate a mode or command
+ */
+ ndelay(nsecs);
+ bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
+ ndelay(nsecs);
+ }
+
+ m->status = status;
+ m->complete(m->context);
+
+ /* normally deactivate chipselect ... unless no error and
+ * cs_change has hinted that the next message will probably
+ * be for this chip too.
+ */
+ if (!(status == 0 && cs_change)) {
+ ndelay(nsecs);
+ bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
+ ndelay(nsecs);
+ }
+
+ spin_lock_irqsave(&bitbang->lock, flags);
+ }
+ bitbang->busy = 0;
+ spin_unlock_irqrestore(&bitbang->lock, flags);
+}
+
+/**
+ * spi_bitbang_transfer - default submit to transfer queue
+ */
+int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m)
+{
+ struct spi_bitbang *bitbang;
+ unsigned long flags;
+
+ m->actual_length = 0;
+ m->status = -EINPROGRESS;
+
+ bitbang = spi_master_get_devdata(spi->master);
+ if (bitbang->shutdown)
+ return -ESHUTDOWN;
+
+ spin_lock_irqsave(&bitbang->lock, flags);
+ list_add_tail(&m->queue, &bitbang->queue);
+ queue_work(bitbang->workqueue, &bitbang->work);
+ spin_unlock_irqrestore(&bitbang->lock, flags);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_transfer);
+
+/*----------------------------------------------------------------------*/
+
+/**
+ * spi_bitbang_start - start up a polled/bitbanging SPI master driver
+ * @bitbang: driver handle
+ *
+ * Caller should have zero-initialized all parts of the structure, and then
+ * provided callbacks for chip selection and I/O loops. If the master has
+ * a transfer method, its final step should call spi_bitbang_transfer; or,
+ * that's the default if the transfer routine is not initialized. It should
+ * also set up the bus number and number of chipselects.
+ *
+ * For i/o loops, provide callbacks either per-word (for bitbanging, or for
+ * hardware that basically exposes a shift register) or per-spi_transfer
+ * (which takes better advantage of hardware like fifos or DMA engines).
+ *
+ * Drivers using per-word I/O loops should use (or call) spi_bitbang_setup and
+ * spi_bitbang_cleanup to handle those spi master methods. Those methods are
+ * the defaults if the bitbang->txrx_bufs routine isn't initialized.
+ *
+ * This routine registers the spi_master, which will process requests in a
+ * dedicated task, keeping IRQs unblocked most of the time. To stop
+ * processing those requests, call spi_bitbang_stop().
+ */
+int spi_bitbang_start(struct spi_bitbang *bitbang)
+{
+ int status;
+
+ if (!bitbang->master || !bitbang->chipselect)
+ return -EINVAL;
+
+ INIT_WORK(&bitbang->work, bitbang_work, bitbang);
+ spin_lock_init(&bitbang->lock);
+ INIT_LIST_HEAD(&bitbang->queue);
+
+ if (!bitbang->master->transfer)
+ bitbang->master->transfer = spi_bitbang_transfer;
+ if (!bitbang->txrx_bufs) {
+ bitbang->use_dma = 0;
+ bitbang->txrx_bufs = spi_bitbang_bufs;
+ if (!bitbang->master->setup) {
+ bitbang->master->setup = spi_bitbang_setup;
+ bitbang->master->cleanup = spi_bitbang_cleanup;
+ }
+ } else if (!bitbang->master->setup)
+ return -EINVAL;
+
+ /* this task is the only thing to touch the SPI bits */
+ bitbang->busy = 0;
+ bitbang->workqueue = create_singlethread_workqueue(
+ bitbang->master->cdev.dev->bus_id);
+ if (bitbang->workqueue == NULL) {
+ status = -EBUSY;
+ goto err1;
+ }
+
+ /* driver may get busy before register() returns, especially
+ * if someone registered boardinfo for devices
+ */
+ status = spi_register_master(bitbang->master);
+ if (status < 0)
+ goto err2;
+
+ return status;
+
+err2:
+ destroy_workqueue(bitbang->workqueue);
+err1:
+ return status;
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_start);
+
+/**
+ * spi_bitbang_stop - stops the task providing spi communication
+ */
+int spi_bitbang_stop(struct spi_bitbang *bitbang)
+{
+ unsigned limit = 500;
+
+ spin_lock_irq(&bitbang->lock);
+ bitbang->shutdown = 0;
+ while (!list_empty(&bitbang->queue) && limit--) {
+ spin_unlock_irq(&bitbang->lock);
+
+ dev_dbg(bitbang->master->cdev.dev, "wait for queue\n");
+ msleep(10);
+
+ spin_lock_irq(&bitbang->lock);
+ }
+ spin_unlock_irq(&bitbang->lock);
+ if (!list_empty(&bitbang->queue)) {
+ dev_err(bitbang->master->cdev.dev, "queue didn't empty\n");
+ return -EBUSY;
+ }
+
+ destroy_workqueue(bitbang->workqueue);
+
+ spi_unregister_master(bitbang->master);
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(spi_bitbang_stop);
+
+MODULE_LICENSE("GPL");
+
diff --git a/drivers/spi/spi_butterfly.c b/drivers/spi/spi_butterfly.c
new file mode 100644
index 0000000..79a3c59
--- /dev/null
+++ b/drivers/spi/spi_butterfly.c
@@ -0,0 +1,423 @@
+/*
+ * spi_butterfly.c - parport-to-butterfly adapter
+ *
+ * Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+#include <linux/config.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/parport.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+#include <linux/spi/flash.h>
+
+#include <linux/mtd/partitions.h>
+
+
+/*
+ * This uses SPI to talk with an "AVR Butterfly", which is a $US20 card
+ * with a battery powered AVR microcontroller and lots of goodies. You
+ * can use GCC to develop firmware for this.
+ *
+ * See Documentation/spi/butterfly for information about how to build
+ * and use this custom parallel port cable.
+ */
+
+#undef HAVE_USI /* nyet */
+
+
+/* DATA output bits (pins 2..9 == D0..D7) */
+#define butterfly_nreset (1 << 1) /* pin 3 */
+
+#define spi_sck_bit (1 << 0) /* pin 2 */
+#define spi_mosi_bit (1 << 7) /* pin 9 */
+
+#define usi_sck_bit (1 << 3) /* pin 5 */
+#define usi_mosi_bit (1 << 4) /* pin 6 */
+
+#define vcc_bits ((1 << 6) | (1 << 5)) /* pins 7, 8 */
+
+/* STATUS input bits */
+#define spi_miso_bit PARPORT_STATUS_BUSY /* pin 11 */
+
+#define usi_miso_bit PARPORT_STATUS_PAPEROUT /* pin 12 */
+
+/* CONTROL output bits */
+#define spi_cs_bit PARPORT_CONTROL_SELECT /* pin 17 */
+/* USI uses no chipselect */
+
+
+
+static inline struct butterfly *spidev_to_pp(struct spi_device *spi)
+{
+ return spi->controller_data;
+}
+
+static inline int is_usidev(struct spi_device *spi)
+{
+#ifdef HAVE_USI
+ return spi->chip_select != 1;
+#else
+ return 0;
+#endif
+}
+
+
+struct butterfly {
+ /* REVISIT ... for now, this must be first */
+ struct spi_bitbang bitbang;
+
+ struct parport *port;
+ struct pardevice *pd;
+
+ u8 lastbyte;
+
+ struct spi_device *dataflash;
+ struct spi_device *butterfly;
+ struct spi_board_info info[2];
+
+};
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * these routines may be slower than necessary because they're hiding
+ * the fact that there are two different SPI busses on this cable: one
+ * to the DataFlash chip (or AVR SPI controller), the other to the
+ * AVR USI controller.
+ */
+
+static inline void
+setsck(struct spi_device *spi, int is_on)
+{
+ struct butterfly *pp = spidev_to_pp(spi);
+ u8 bit, byte = pp->lastbyte;
+
+ if (is_usidev(spi))
+ bit = usi_sck_bit;
+ else
+ bit = spi_sck_bit;
+
+ if (is_on)
+ byte |= bit;
+ else
+ byte &= ~bit;
+ parport_write_data(pp->port, byte);
+ pp->lastbyte = byte;
+}
+
+static inline void
+setmosi(struct spi_device *spi, int is_on)
+{
+ struct butterfly *pp = spidev_to_pp(spi);
+ u8 bit, byte = pp->lastbyte;
+
+ if (is_usidev(spi))
+ bit = usi_mosi_bit;
+ else
+ bit = spi_mosi_bit;
+
+ if (is_on)
+ byte |= bit;
+ else
+ byte &= ~bit;
+ parport_write_data(pp->port, byte);
+ pp->lastbyte = byte;
+}
+
+static inline int getmiso(struct spi_device *spi)
+{
+ struct butterfly *pp = spidev_to_pp(spi);
+ int value;
+ u8 bit;
+
+ if (is_usidev(spi))
+ bit = usi_miso_bit;
+ else
+ bit = spi_miso_bit;
+
+ /* only STATUS_BUSY is NOT negated */
+ value = !(parport_read_status(pp->port) & bit);
+ return (bit == PARPORT_STATUS_BUSY) ? value : !value;
+}
+
+static void butterfly_chipselect(struct spi_device *spi, int value)
+{
+ struct butterfly *pp = spidev_to_pp(spi);
+
+ /* set default clock polarity */
+ if (value)
+ setsck(spi, spi->mode & SPI_CPOL);
+
+ /* no chipselect on this USI link config */
+ if (is_usidev(spi))
+ return;
+
+ /* here, value == "activate or not" */
+
+ /* most PARPORT_CONTROL_* bits are negated */
+ if (spi_cs_bit == PARPORT_CONTROL_INIT)
+ value = !value;
+
+ /* here, value == "bit value to write in control register" */
+
+ parport_frob_control(pp->port, spi_cs_bit, value ? spi_cs_bit : 0);
+}
+
+
+/* we only needed to implement one mode here, and choose SPI_MODE_0 */
+
+#define spidelay(X) do{}while(0)
+//#define spidelay ndelay
+
+#define EXPAND_BITBANG_TXRX
+#include <linux/spi/spi_bitbang.h>
+
+static u32
+butterfly_txrx_word_mode0(struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits)
+{
+ return bitbang_txrx_be_cpha0(spi, nsecs, 0, word, bits);
+}
+
+/*----------------------------------------------------------------------*/
+
+/* override default partitioning with cmdlinepart */
+static struct mtd_partition partitions[] = { {
+ /* JFFS2 wants partitions of 4*N blocks for this device ... */
+
+ /* sector 0 = 8 pages * 264 bytes/page (1 block)
+ * sector 1 = 248 pages * 264 bytes/page
+ */
+ .name = "bookkeeping", // 66 KB
+ .offset = 0,
+ .size = (8 + 248) * 264,
+// .mask_flags = MTD_WRITEABLE,
+}, {
+ /* sector 2 = 256 pages * 264 bytes/page
+ * sectors 3-5 = 512 pages * 264 bytes/page
+ */
+ .name = "filesystem", // 462 KB
+ .offset = MTDPART_OFS_APPEND,
+ .size = MTDPART_SIZ_FULL,
+} };
+
+static struct flash_platform_data flash = {
+ .name = "butterflash",
+ .parts = partitions,
+ .nr_parts = ARRAY_SIZE(partitions),
+};
+
+
+/* REVISIT remove this ugly global and its "only one" limitation */
+static struct butterfly *butterfly;
+
+static void butterfly_attach(struct parport *p)
+{
+ struct pardevice *pd;
+ int status;
+ struct butterfly *pp;
+ struct spi_master *master;
+ struct platform_device *pdev;
+
+ if (butterfly)
+ return;
+
+ /* REVISIT: this just _assumes_ a butterfly is there ... no probe,
+ * and no way to be selective about what it binds to.
+ */
+
+ /* FIXME where should master->cdev.dev come from?
+ * e.g. /sys/bus/pnp0/00:0b, some PCI thing, etc
+ * setting up a platform device like this is an ugly kluge...
+ */
+ pdev = platform_device_register_simple("butterfly", -1, NULL, 0);
+
+ master = spi_alloc_master(&pdev->dev, sizeof *pp);
+ if (!master) {
+ status = -ENOMEM;
+ goto done;
+ }
+ pp = spi_master_get_devdata(master);
+
+ /*
+ * SPI and bitbang hookup
+ *
+ * use default setup(), cleanup(), and transfer() methods; and
+ * only bother implementing mode 0. Start it later.
+ */
+ master->bus_num = 42;
+ master->num_chipselect = 2;
+
+ pp->bitbang.master = spi_master_get(master);
+ pp->bitbang.chipselect = butterfly_chipselect;
+ pp->bitbang.txrx_word[SPI_MODE_0] = butterfly_txrx_word_mode0;
+
+ /*
+ * parport hookup
+ */
+ pp->port = p;
+ pd = parport_register_device(p, "spi_butterfly",
+ NULL, NULL, NULL,
+ 0 /* FLAGS */, pp);
+ if (!pd) {
+ status = -ENOMEM;
+ goto clean0;
+ }
+ pp->pd = pd;
+
+ status = parport_claim(pd);
+ if (status < 0)
+ goto clean1;
+
+ /*
+ * Butterfly reset, powerup, run firmware
+ */
+ pr_debug("%s: powerup/reset Butterfly\n", p->name);
+
+ /* nCS for dataflash (this bit is inverted on output) */
+ parport_frob_control(pp->port, spi_cs_bit, 0);
+
+ /* stabilize power with chip in reset (nRESET), and
+ * both spi_sck_bit and usi_sck_bit clear (CPOL=0)
+ */
+ pp->lastbyte |= vcc_bits;
+ parport_write_data(pp->port, pp->lastbyte);
+ msleep(5);
+
+ /* take it out of reset; assume long reset delay */
+ pp->lastbyte |= butterfly_nreset;
+ parport_write_data(pp->port, pp->lastbyte);
+ msleep(100);
+
+
+ /*
+ * Start SPI ... for now, hide that we're two physical busses.
+ */
+ status = spi_bitbang_start(&pp->bitbang);
+ if (status < 0)
+ goto clean2;
+
+ /* Bus 1 lets us talk to at45db041b (firmware disables AVR)
+ * or AVR (firmware resets at45, acts as spi slave)
+ */
+ pp->info[0].max_speed_hz = 15 * 1000 * 1000;
+ strcpy(pp->info[0].modalias, "mtd_dataflash");
+ pp->info[0].platform_data = &flash;
+ pp->info[0].chip_select = 1;
+ pp->info[0].controller_data = pp;
+ pp->dataflash = spi_new_device(pp->bitbang.master, &pp->info[0]);
+ if (pp->dataflash)
+ pr_debug("%s: dataflash at %s\n", p->name,
+ pp->dataflash->dev.bus_id);
+
+#ifdef HAVE_USI
+ /* even more custom AVR firmware */
+ pp->info[1].max_speed_hz = 10 /* ?? */ * 1000 * 1000;
+ strcpy(pp->info[1].modalias, "butterfly");
+ // pp->info[1].platform_data = ... TBD ... ;
+ pp->info[1].chip_select = 2,
+ pp->info[1].controller_data = pp;
+ pp->butterfly = spi_new_device(pp->bitbang.master, &pp->info[1]);
+ if (pp->butterfly)
+ pr_debug("%s: butterfly at %s\n", p->name,
+ pp->butterfly->dev.bus_id);
+
+ /* FIXME setup ACK for the IRQ line ... */
+#endif
+
+ // dev_info(_what?_, ...)
+ pr_info("%s: AVR Butterfly\n", p->name);
+ butterfly = pp;
+ return;
+
+clean2:
+ /* turn off VCC */
+ parport_write_data(pp->port, 0);
+
+ parport_release(pp->pd);
+clean1:
+ parport_unregister_device(pd);
+clean0:
+ (void) spi_master_put(pp->bitbang.master);
+done:
+ platform_device_unregister(pdev);
+ pr_debug("%s: butterfly probe, fail %d\n", p->name, status);
+}
+
+static void butterfly_detach(struct parport *p)
+{
+ struct butterfly *pp;
+ struct platform_device *pdev;
+ int status;
+
+ /* FIXME this global is ugly ... but, how to quickly get from
+ * the parport to the "struct butterfly" associated with it?
+ * "old school" driver-internal device lists?
+ */
+ if (!butterfly || butterfly->port != p)
+ return;
+ pp = butterfly;
+ butterfly = NULL;
+
+#ifdef HAVE_USI
+ spi_unregister_device(pp->butterfly);
+ pp->butterfly = NULL;
+#endif
+ spi_unregister_device(pp->dataflash);
+ pp->dataflash = NULL;
+
+ status = spi_bitbang_stop(&pp->bitbang);
+
+ /* turn off VCC */
+ parport_write_data(pp->port, 0);
+ msleep(10);
+
+ parport_release(pp->pd);
+ parport_unregister_device(pp->pd);
+
+ pdev = to_platform_device(pp->bitbang.master->cdev.dev);
+
+ (void) spi_master_put(pp->bitbang.master);
+
+ platform_device_unregister(pdev);
+}
+
+static struct parport_driver butterfly_driver = {
+ .name = "spi_butterfly",
+ .attach = butterfly_attach,
+ .detach = butterfly_detach,
+};
+
+
+static int __init butterfly_init(void)
+{
+ return parport_register_driver(&butterfly_driver);
+}
+device_initcall(butterfly_init);
+
+static void __exit butterfly_exit(void)
+{
+ parport_unregister_driver(&butterfly_driver);
+}
+module_exit(butterfly_exit);
+
+MODULE_LICENSE("GPL");
diff --git a/include/linux/spi/ads7846.h b/include/linux/spi/ads7846.h
new file mode 100644
index 0000000..72261e0
--- /dev/null
+++ b/include/linux/spi/ads7846.h
@@ -0,0 +1,18 @@
+/* linux/spi/ads7846.h */
+
+/* Touchscreen characteristics vary between boards and models. The
+ * platform_data for the device's "struct device" holds this information.
+ *
+ * It's OK if the min/max values are zero.
+ */
+struct ads7846_platform_data {
+ u16 model; /* 7843, 7845, 7846. */
+ u16 vref_delay_usecs; /* 0 for external vref; etc */
+ u16 x_plate_ohms;
+ u16 y_plate_ohms;
+
+ u16 x_min, x_max;
+ u16 y_min, y_max;
+ u16 pressure_min, pressure_max;
+};
+
diff --git a/include/linux/spi/flash.h b/include/linux/spi/flash.h
new file mode 100644
index 0000000..3f22932
--- /dev/null
+++ b/include/linux/spi/flash.h
@@ -0,0 +1,31 @@
+#ifndef LINUX_SPI_FLASH_H
+#define LINUX_SPI_FLASH_H
+
+struct mtd_partition;
+
+/**
+ * struct flash_platform_data: board-specific flash data
+ * @name: optional flash device name (eg, as used with mtdparts=)
+ * @parts: optional array of mtd_partitions for static partitioning
+ * @nr_parts: number of mtd_partitions for static partitoning
+ * @type: optional flash device type (e.g. m25p80 vs m25p64), for use
+ * with chips that can't be queried for JEDEC or other IDs
+ *
+ * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
+ * provide information about SPI flash parts (such as DataFlash) to
+ * help set up the device and its appropriate default partitioning.
+ *
+ * Note that for DataFlash, sizes for pages, blocks, and sectors are
+ * rarely powers of two; and partitions should be sector-aligned.
+ */
+struct flash_platform_data {
+ char *name;
+ struct mtd_partition *parts;
+ unsigned int nr_parts;
+
+ char *type;
+
+ /* we'll likely add more ... use JEDEC IDs, etc */
+};
+
+#endif
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
new file mode 100644
index 0000000..b05f146
--- /dev/null
+++ b/include/linux/spi/spi.h
@@ -0,0 +1,668 @@
+/*
+ * Copyright (C) 2005 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __LINUX_SPI_H
+#define __LINUX_SPI_H
+
+/*
+ * INTERFACES between SPI master-side drivers and SPI infrastructure.
+ * (There's no SPI slave support for Linux yet...)
+ */
+extern struct bus_type spi_bus_type;
+
+/**
+ * struct spi_device - Master side proxy for an SPI slave device
+ * @dev: Driver model representation of the device.
+ * @master: SPI controller used with the device.
+ * @max_speed_hz: Maximum clock rate to be used with this chip
+ * (on this board); may be changed by the device's driver.
+ * @chip-select: Chipselect, distinguishing chips handled by "master".
+ * @mode: The spi mode defines how data is clocked out and in.
+ * This may be changed by the device's driver.
+ * @bits_per_word: Data transfers involve one or more words; word sizes
+ * like eight or 12 bits are common. In-memory wordsizes are
+ * powers of two bytes (e.g. 20 bit samples use 32 bits).
+ * This may be changed by the device's driver.
+ * @irq: Negative, or the number passed to request_irq() to receive
+ * interrupts from this device.
+ * @controller_state: Controller's runtime state
+ * @controller_data: Board-specific definitions for controller, such as
+ * FIFO initialization parameters; from board_info.controller_data
+ *
+ * An spi_device is used to interchange data between an SPI slave
+ * (usually a discrete chip) and CPU memory.
+ *
+ * In "dev", the platform_data is used to hold information about this
+ * device that's meaningful to the device's protocol driver, but not
+ * to its controller. One example might be an identifier for a chip
+ * variant with slightly different functionality.
+ */
+struct spi_device {
+ struct device dev;
+ struct spi_master *master;
+ u32 max_speed_hz;
+ u8 chip_select;
+ u8 mode;
+#define SPI_CPHA 0x01 /* clock phase */
+#define SPI_CPOL 0x02 /* clock polarity */
+#define SPI_MODE_0 (0|0) /* (original MicroWire) */
+#define SPI_MODE_1 (0|SPI_CPHA)
+#define SPI_MODE_2 (SPI_CPOL|0)
+#define SPI_MODE_3 (SPI_CPOL|SPI_CPHA)
+#define SPI_CS_HIGH 0x04 /* chipselect active high? */
+ u8 bits_per_word;
+ int irq;
+ void *controller_state;
+ void *controller_data;
+ const char *modalias;
+
+ // likely need more hooks for more protocol options affecting how
+ // the controller talks to each chip, like:
+ // - bit order (default is wordwise msb-first)
+ // - memory packing (12 bit samples into low bits, others zeroed)
+ // - priority
+ // - drop chipselect after each word
+ // - chipselect delays
+ // - ...
+};
+
+static inline struct spi_device *to_spi_device(struct device *dev)
+{
+ return dev ? container_of(dev, struct spi_device, dev) : NULL;
+}
+
+/* most drivers won't need to care about device refcounting */
+static inline struct spi_device *spi_dev_get(struct spi_device *spi)
+{
+ return (spi && get_device(&spi->dev)) ? spi : NULL;
+}
+
+static inline void spi_dev_put(struct spi_device *spi)
+{
+ if (spi)
+ put_device(&spi->dev);
+}
+
+/* ctldata is for the bus_master driver's runtime state */
+static inline void *spi_get_ctldata(struct spi_device *spi)
+{
+ return spi->controller_state;
+}
+
+static inline void spi_set_ctldata(struct spi_device *spi, void *state)
+{
+ spi->controller_state = state;
+}
+
+
+struct spi_message;
+
+
+
+struct spi_driver {
+ int (*probe)(struct spi_device *spi);
+ int (*remove)(struct spi_device *spi);
+ void (*shutdown)(struct spi_device *spi);
+ int (*suspend)(struct spi_device *spi, pm_message_t mesg);
+ int (*resume)(struct spi_device *spi);
+ struct device_driver driver;
+};
+
+static inline struct spi_driver *to_spi_driver(struct device_driver *drv)
+{
+ return drv ? container_of(drv, struct spi_driver, driver) : NULL;
+}
+
+extern int spi_register_driver(struct spi_driver *sdrv);
+
+static inline void spi_unregister_driver(struct spi_driver *sdrv)
+{
+ if (!sdrv)
+ return;
+ driver_unregister(&sdrv->driver);
+}
+
+
+
+/**
+ * struct spi_master - interface to SPI master controller
+ * @cdev: class interface to this driver
+ * @bus_num: board-specific (and often SOC-specific) identifier for a
+ * given SPI controller.
+ * @num_chipselect: chipselects are used to distinguish individual
+ * SPI slaves, and are numbered from zero to num_chipselects.
+ * each slave has a chipselect signal, but it's common that not
+ * every chipselect is connected to a slave.
+ * @setup: updates the device mode and clocking records used by a
+ * device's SPI controller; protocol code may call this.
+ * @transfer: adds a message to the controller's transfer queue.
+ * @cleanup: frees controller-specific state
+ *
+ * Each SPI master controller can communicate with one or more spi_device
+ * children. These make a small bus, sharing MOSI, MISO and SCK signals
+ * but not chip select signals. Each device may be configured to use a
+ * different clock rate, since those shared signals are ignored unless
+ * the chip is selected.
+ *
+ * The driver for an SPI controller manages access to those devices through
+ * a queue of spi_message transactions, copyin data between CPU memory and
+ * an SPI slave device). For each such message it queues, it calls the
+ * message's completion function when the transaction completes.
+ */
+struct spi_master {
+ struct class_device cdev;
+
+ /* other than zero (== assign one dynamically), bus_num is fully
+ * board-specific. usually that simplifies to being SOC-specific.
+ * example: one SOC has three SPI controllers, numbered 1..3,
+ * and one board's schematics might show it using SPI-2. software
+ * would normally use bus_num=2 for that controller.
+ */
+ u16 bus_num;
+
+ /* chipselects will be integral to many controllers; some others
+ * might use board-specific GPIOs.
+ */
+ u16 num_chipselect;
+
+ /* setup mode and clock, etc (spi driver may call many times) */
+ int (*setup)(struct spi_device *spi);
+
+ /* bidirectional bulk transfers
+ *
+ * + The transfer() method may not sleep; its main role is
+ * just to add the message to the queue.
+ * + For now there's no remove-from-queue operation, or
+ * any other request management
+ * + To a given spi_device, message queueing is pure fifo
+ *
+ * + The master's main job is to process its message queue,
+ * selecting a chip then transferring data
+ * + If there are multiple spi_device children, the i/o queue
+ * arbitration algorithm is unspecified (round robin, fifo,
+ * priority, reservations, preemption, etc)
+ *
+ * + Chipselect stays active during the entire message
+ * (unless modified by spi_transfer.cs_change != 0).
+ * + The message transfers use clock and SPI mode parameters
+ * previously established by setup() for this device
+ */
+ int (*transfer)(struct spi_device *spi,
+ struct spi_message *mesg);
+
+ /* called on release() to free memory provided by spi_master */
+ void (*cleanup)(const struct spi_device *spi);
+};
+
+static inline void *spi_master_get_devdata(struct spi_master *master)
+{
+ return class_get_devdata(&master->cdev);
+}
+
+static inline void spi_master_set_devdata(struct spi_master *master, void *data)
+{
+ class_set_devdata(&master->cdev, data);
+}
+
+static inline struct spi_master *spi_master_get(struct spi_master *master)
+{
+ if (!master || !class_device_get(&master->cdev))
+ return NULL;
+ return master;
+}
+
+static inline void spi_master_put(struct spi_master *master)
+{
+ if (master)
+ class_device_put(&master->cdev);
+}
+
+
+/* the spi driver core manages memory for the spi_master classdev */
+extern struct spi_master *
+spi_alloc_master(struct device *host, unsigned size);
+
+extern int spi_register_master(struct spi_master *master);
+extern void spi_unregister_master(struct spi_master *master);
+
+extern struct spi_master *spi_busnum_to_master(u16 busnum);
+
+/*---------------------------------------------------------------------------*/
+
+/*
+ * I/O INTERFACE between SPI controller and protocol drivers
+ *
+ * Protocol drivers use a queue of spi_messages, each transferring data
+ * between the controller and memory buffers.
+ *
+ * The spi_messages themselves consist of a series of read+write transfer
+ * segments. Those segments always read the same number of bits as they
+ * write; but one or the other is easily ignored by passing a null buffer
+ * pointer. (This is unlike most types of I/O API, because SPI hardware
+ * is full duplex.)
+ *
+ * NOTE: Allocation of spi_transfer and spi_message memory is entirely
+ * up to the protocol driver, which guarantees the integrity of both (as
+ * well as the data buffers) for as long as the message is queued.
+ */
+
+/**
+ * struct spi_transfer - a read/write buffer pair
+ * @tx_buf: data to be written (dma-safe memory), or NULL
+ * @rx_buf: data to be read (dma-safe memory), or NULL
+ * @tx_dma: DMA address of tx_buf, if spi_message.is_dma_mapped
+ * @rx_dma: DMA address of rx_buf, if spi_message.is_dma_mapped
+ * @len: size of rx and tx buffers (in bytes)
+ * @cs_change: affects chipselect after this transfer completes
+ * @delay_usecs: microseconds to delay after this transfer before
+ * (optionally) changing the chipselect status, then starting
+ * the next transfer or completing this spi_message.
+ * @transfer_list: transfers are sequenced through spi_message.transfers
+ *
+ * SPI transfers always write the same number of bytes as they read.
+ * Protocol drivers should always provide rx_buf and/or tx_buf.
+ * In some cases, they may also want to provide DMA addresses for
+ * the data being transferred; that may reduce overhead, when the
+ * underlying driver uses dma.
+ *
+ * If the transmit buffer is null, undefined data will be shifted out
+ * while filling rx_buf. If the receive buffer is null, the data
+ * shifted in will be discarded. Only "len" bytes shift out (or in).
+ * It's an error to try to shift out a partial word. (For example, by
+ * shifting out three bytes with word size of sixteen or twenty bits;
+ * the former uses two bytes per word, the latter uses four bytes.)
+ *
+ * All SPI transfers start with the relevant chipselect active. Normally
+ * it stays selected until after the last transfer in a message. Drivers
+ * can affect the chipselect signal using cs_change:
+ *
+ * (i) If the transfer isn't the last one in the message, this flag is
+ * used to make the chipselect briefly go inactive in the middle of the
+ * message. Toggling chipselect in this way may be needed to terminate
+ * a chip command, letting a single spi_message perform all of group of
+ * chip transactions together.
+ *
+ * (ii) When the transfer is the last one in the message, the chip may
+ * stay selected until the next transfer. This is purely a performance
+ * hint; the controller driver may need to select a different device
+ * for the next message.
+ *
+ * The code that submits an spi_message (and its spi_transfers)
+ * to the lower layers is responsible for managing its memory.
+ * Zero-initialize every field you don't set up explicitly, to
+ * insulate against future API updates. After you submit a message
+ * and its transfers, ignore them until its completion callback.
+ */
+struct spi_transfer {
+ /* it's ok if tx_buf == rx_buf (right?)
+ * for MicroWire, one buffer must be null
+ * buffers must work with dma_*map_single() calls, unless
+ * spi_message.is_dma_mapped reports a pre-existing mapping
+ */
+ const void *tx_buf;
+ void *rx_buf;
+ unsigned len;
+
+ dma_addr_t tx_dma;
+ dma_addr_t rx_dma;
+
+ unsigned cs_change:1;
+ u16 delay_usecs;
+
+ struct list_head transfer_list;
+};
+
+/**
+ * struct spi_message - one multi-segment SPI transaction
+ * @transfers: list of transfer segments in this transaction
+ * @spi: SPI device to which the transaction is queued
+ * @is_dma_mapped: if true, the caller provided both dma and cpu virtual
+ * addresses for each transfer buffer
+ * @complete: called to report transaction completions
+ * @context: the argument to complete() when it's called
+ * @actual_length: the total number of bytes that were transferred in all
+ * successful segments
+ * @status: zero for success, else negative errno
+ * @queue: for use by whichever driver currently owns the message
+ * @state: for use by whichever driver currently owns the message
+ *
+ * An spi_message is used to execute an atomic sequence of data transfers,
+ * each represented by a struct spi_transfer. The sequence is "atomic"
+ * in the sense that no other spi_message may use that SPI bus until that
+ * sequence completes. On some systems, many such sequences can execute as
+ * as single programmed DMA transfer. On all systems, these messages are
+ * queued, and might complete after transactions to other devices. Messages
+ * sent to a given spi_device are alway executed in FIFO order.
+ *
+ * The code that submits an spi_message (and its spi_transfers)
+ * to the lower layers is responsible for managing its memory.
+ * Zero-initialize every field you don't set up explicitly, to
+ * insulate against future API updates. After you submit a message
+ * and its transfers, ignore them until its completion callback.
+ */
+struct spi_message {
+ struct list_head transfers;
+
+ struct spi_device *spi;
+
+ unsigned is_dma_mapped:1;
+
+ /* REVISIT: we might want a flag affecting the behavior of the
+ * last transfer ... allowing things like "read 16 bit length L"
+ * immediately followed by "read L bytes". Basically imposing
+ * a specific message scheduling algorithm.
+ *
+ * Some controller drivers (message-at-a-time queue processing)
+ * could provide that as their default scheduling algorithm. But
+ * others (with multi-message pipelines) could need a flag to
+ * tell them about such special cases.
+ */
+
+ /* completion is reported through a callback */
+ void (*complete)(void *context);
+ void *context;
+ unsigned actual_length;
+ int status;
+
+ /* for optional use by whatever driver currently owns the
+ * spi_message ... between calls to spi_async and then later
+ * complete(), that's the spi_master controller driver.
+ */
+ struct list_head queue;
+ void *state;
+};
+
+static inline void spi_message_init(struct spi_message *m)
+{
+ memset(m, 0, sizeof *m);
+ INIT_LIST_HEAD(&m->transfers);
+}
+
+static inline void
+spi_message_add_tail(struct spi_transfer *t, struct spi_message *m)
+{
+ list_add_tail(&t->transfer_list, &m->transfers);
+}
+
+static inline void
+spi_transfer_del(struct spi_transfer *t)
+{
+ list_del(&t->transfer_list);
+}
+
+/* It's fine to embed message and transaction structures in other data
+ * structures so long as you don't free them while they're in use.
+ */
+
+static inline struct spi_message *spi_message_alloc(unsigned ntrans, gfp_t flags)
+{
+ struct spi_message *m;
+
+ m = kzalloc(sizeof(struct spi_message)
+ + ntrans * sizeof(struct spi_transfer),
+ flags);
+ if (m) {
+ int i;
+ struct spi_transfer *t = (struct spi_transfer *)(m + 1);
+
+ INIT_LIST_HEAD(&m->transfers);
+ for (i = 0; i < ntrans; i++, t++)
+ spi_message_add_tail(t, m);
+ }
+ return m;
+}
+
+static inline void spi_message_free(struct spi_message *m)
+{
+ kfree(m);
+}
+
+/**
+ * spi_setup -- setup SPI mode and clock rate
+ * @spi: the device whose settings are being modified
+ *
+ * SPI protocol drivers may need to update the transfer mode if the
+ * device doesn't work with the mode 0 default. They may likewise need
+ * to update clock rates or word sizes from initial values. This function
+ * changes those settings, and must be called from a context that can sleep.
+ * The changes take effect the next time the device is selected and data
+ * is transferred to or from it.
+ */
+static inline int
+spi_setup(struct spi_device *spi)
+{
+ return spi->master->setup(spi);
+}
+
+
+/**
+ * spi_async -- asynchronous SPI transfer
+ * @spi: device with which data will be exchanged
+ * @message: describes the data transfers, including completion callback
+ *
+ * This call may be used in_irq and other contexts which can't sleep,
+ * as well as from task contexts which can sleep.
+ *
+ * The completion callback is invoked in a context which can't sleep.
+ * Before that invocation, the value of message->status is undefined.
+ * When the callback is issued, message->status holds either zero (to
+ * indicate complete success) or a negative error code. After that
+ * callback returns, the driver which issued the transfer request may
+ * deallocate the associated memory; it's no longer in use by any SPI
+ * core or controller driver code.
+ *
+ * Note that although all messages to a spi_device are handled in
+ * FIFO order, messages may go to different devices in other orders.
+ * Some device might be higher priority, or have various "hard" access
+ * time requirements, for example.
+ *
+ * On detection of any fault during the transfer, processing of
+ * the entire message is aborted, and the device is deselected.
+ * Until returning from the associated message completion callback,
+ * no other spi_message queued to that device will be processed.
+ * (This rule applies equally to all the synchronous transfer calls,
+ * which are wrappers around this core asynchronous primitive.)
+ */
+static inline int
+spi_async(struct spi_device *spi, struct spi_message *message)
+{
+ message->spi = spi;
+ return spi->master->transfer(spi, message);
+}
+
+/*---------------------------------------------------------------------------*/
+
+/* All these synchronous SPI transfer routines are utilities layered
+ * over the core async transfer primitive. Here, "synchronous" means
+ * they will sleep uninterruptibly until the async transfer completes.
+ */
+
+extern int spi_sync(struct spi_device *spi, struct spi_message *message);
+
+/**
+ * spi_write - SPI synchronous write
+ * @spi: device to which data will be written
+ * @buf: data buffer
+ * @len: data buffer size
+ *
+ * This writes the buffer and returns zero or a negative error code.
+ * Callable only from contexts that can sleep.
+ */
+static inline int
+spi_write(struct spi_device *spi, const u8 *buf, size_t len)
+{
+ struct spi_transfer t = {
+ .tx_buf = buf,
+ .len = len,
+ };
+ struct spi_message m;
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t, &m);
+ return spi_sync(spi, &m);
+}
+
+/**
+ * spi_read - SPI synchronous read
+ * @spi: device from which data will be read
+ * @buf: data buffer
+ * @len: data buffer size
+ *
+ * This writes the buffer and returns zero or a negative error code.
+ * Callable only from contexts that can sleep.
+ */
+static inline int
+spi_read(struct spi_device *spi, u8 *buf, size_t len)
+{
+ struct spi_transfer t = {
+ .rx_buf = buf,
+ .len = len,
+ };
+ struct spi_message m;
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t, &m);
+ return spi_sync(spi, &m);
+}
+
+/* this copies txbuf and rxbuf data; for small transfers only! */
+extern int spi_write_then_read(struct spi_device *spi,
+ const u8 *txbuf, unsigned n_tx,
+ u8 *rxbuf, unsigned n_rx);
+
+/**
+ * spi_w8r8 - SPI synchronous 8 bit write followed by 8 bit read
+ * @spi: device with which data will be exchanged
+ * @cmd: command to be written before data is read back
+ *
+ * This returns the (unsigned) eight bit number returned by the
+ * device, or else a negative error code. Callable only from
+ * contexts that can sleep.
+ */
+static inline ssize_t spi_w8r8(struct spi_device *spi, u8 cmd)
+{
+ ssize_t status;
+ u8 result;
+
+ status = spi_write_then_read(spi, &cmd, 1, &result, 1);
+
+ /* return negative errno or unsigned value */
+ return (status < 0) ? status : result;
+}
+
+/**
+ * spi_w8r16 - SPI synchronous 8 bit write followed by 16 bit read
+ * @spi: device with which data will be exchanged
+ * @cmd: command to be written before data is read back
+ *
+ * This returns the (unsigned) sixteen bit number returned by the
+ * device, or else a negative error code. Callable only from
+ * contexts that can sleep.
+ *
+ * The number is returned in wire-order, which is at least sometimes
+ * big-endian.
+ */
+static inline ssize_t spi_w8r16(struct spi_device *spi, u8 cmd)
+{
+ ssize_t status;
+ u16 result;
+
+ status = spi_write_then_read(spi, &cmd, 1, (u8 *) &result, 2);
+
+ /* return negative errno or unsigned value */
+ return (status < 0) ? status : result;
+}
+
+/*---------------------------------------------------------------------------*/
+
+/*
+ * INTERFACE between board init code and SPI infrastructure.
+ *
+ * No SPI driver ever sees these SPI device table segments, but
+ * it's how the SPI core (or adapters that get hotplugged) grows
+ * the driver model tree.
+ *
+ * As a rule, SPI devices can't be probed. Instead, board init code
+ * provides a table listing the devices which are present, with enough
+ * information to bind and set up the device's driver. There's basic
+ * support for nonstatic configurations too; enough to handle adding
+ * parport adapters, or microcontrollers acting as USB-to-SPI bridges.
+ */
+
+/* board-specific information about each SPI device */
+struct spi_board_info {
+ /* the device name and module name are coupled, like platform_bus;
+ * "modalias" is normally the driver name.
+ *
+ * platform_data goes to spi_device.dev.platform_data,
+ * controller_data goes to spi_device.controller_data,
+ * irq is copied too
+ */
+ char modalias[KOBJ_NAME_LEN];
+ const void *platform_data;
+ void *controller_data;
+ int irq;
+
+ /* slower signaling on noisy or low voltage boards */
+ u32 max_speed_hz;
+
+
+ /* bus_num is board specific and matches the bus_num of some
+ * spi_master that will probably be registered later.
+ *
+ * chip_select reflects how this chip is wired to that master;
+ * it's less than num_chipselect.
+ */
+ u16 bus_num;
+ u16 chip_select;
+
+ /* ... may need additional spi_device chip config data here.
+ * avoid stuff protocol drivers can set; but include stuff
+ * needed to behave without being bound to a driver:
+ * - chipselect polarity
+ * - quirks like clock rate mattering when not selected
+ */
+};
+
+#ifdef CONFIG_SPI
+extern int
+spi_register_board_info(struct spi_board_info const *info, unsigned n);
+#else
+/* board init code may ignore whether SPI is configured or not */
+static inline int
+spi_register_board_info(struct spi_board_info const *info, unsigned n)
+ { return 0; }
+#endif
+
+
+/* If you're hotplugging an adapter with devices (parport, usb, etc)
+ * use spi_new_device() to describe each device. You can also call
+ * spi_unregister_device() to start making that device vanish, but
+ * normally that would be handled by spi_unregister_master().
+ */
+extern struct spi_device *
+spi_new_device(struct spi_master *, struct spi_board_info *);
+
+static inline void
+spi_unregister_device(struct spi_device *spi)
+{
+ if (spi)
+ device_unregister(&spi->dev);
+}
+
+#endif /* __LINUX_SPI_H */
diff --git a/include/linux/spi/spi_bitbang.h b/include/linux/spi/spi_bitbang.h
new file mode 100644
index 0000000..c961fe9
--- /dev/null
+++ b/include/linux/spi/spi_bitbang.h
@@ -0,0 +1,135 @@
+#ifndef __SPI_BITBANG_H
+#define __SPI_BITBANG_H
+
+/*
+ * Mix this utility code with some glue code to get one of several types of
+ * simple SPI master driver. Two do polled word-at-a-time I/O:
+ *
+ * - GPIO/parport bitbangers. Provide chipselect() and txrx_word[](),
+ * expanding the per-word routines from the inline templates below.
+ *
+ * - Drivers for controllers resembling bare shift registers. Provide
+ * chipselect() and txrx_word[](), with custom setup()/cleanup() methods
+ * that use your controller's clock and chipselect registers.
+ *
+ * Some hardware works well with requests at spi_transfer scope:
+ *
+ * - Drivers leveraging smarter hardware, with fifos or DMA; or for half
+ * duplex (MicroWire) controllers. Provide chipslect() and txrx_bufs(),
+ * and custom setup()/cleanup() methods.
+ */
+struct spi_bitbang {
+ struct workqueue_struct *workqueue;
+ struct work_struct work;
+
+ spinlock_t lock;
+ struct list_head queue;
+ u8 busy;
+ u8 shutdown;
+ u8 use_dma;
+
+ struct spi_master *master;
+
+ void (*chipselect)(struct spi_device *spi, int is_on);
+#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */
+#define BITBANG_CS_INACTIVE 0
+
+ /* txrx_bufs() may handle dma mapping for transfers that don't
+ * already have one (transfer.{tx,rx}_dma is zero), or use PIO
+ */
+ int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t);
+
+ /* txrx_word[SPI_MODE_*]() just looks like a shift register */
+ u32 (*txrx_word[4])(struct spi_device *spi,
+ unsigned nsecs,
+ u32 word, u8 bits);
+};
+
+/* you can call these default bitbang->master methods from your custom
+ * methods, if you like.
+ */
+extern int spi_bitbang_setup(struct spi_device *spi);
+extern void spi_bitbang_cleanup(const struct spi_device *spi);
+extern int spi_bitbang_transfer(struct spi_device *spi, struct spi_message *m);
+
+/* start or stop queue processing */
+extern int spi_bitbang_start(struct spi_bitbang *spi);
+extern int spi_bitbang_stop(struct spi_bitbang *spi);
+
+#endif /* __SPI_BITBANG_H */
+
+/*-------------------------------------------------------------------------*/
+
+#ifdef EXPAND_BITBANG_TXRX
+
+/*
+ * The code that knows what GPIO pins do what should have declared four
+ * functions, ideally as inlines, before #defining EXPAND_BITBANG_TXRX
+ * and including this header:
+ *
+ * void setsck(struct spi_device *, int is_on);
+ * void setmosi(struct spi_device *, int is_on);
+ * int getmiso(struct spi_device *);
+ * void spidelay(unsigned);
+ *
+ * A non-inlined routine would call bitbang_txrx_*() routines. The
+ * main loop could easily compile down to a handful of instructions,
+ * especially if the delay is a NOP (to run at peak speed).
+ *
+ * Since this is software, the timings may not be exactly what your board's
+ * chips need ... there may be several reasons you'd need to tweak timings
+ * in these routines, not just make to make it faster or slower to match a
+ * particular CPU clock rate.
+ */
+
+static inline u32
+bitbang_txrx_be_cpha0(struct spi_device *spi,
+ unsigned nsecs, unsigned cpol,
+ u32 word, u8 bits)
+{
+ /* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */
+
+ /* clock starts at inactive polarity */
+ for (word <<= (32 - bits); likely(bits); bits--) {
+
+ /* setup MSB (to slave) on trailing edge */
+ setmosi(spi, word & (1 << 31));
+ spidelay(nsecs); /* T(setup) */
+
+ setsck(spi, !cpol);
+ spidelay(nsecs);
+
+ /* sample MSB (from slave) on leading edge */
+ word <<= 1;
+ word |= getmiso(spi);
+ setsck(spi, cpol);
+ }
+ return word;
+}
+
+static inline u32
+bitbang_txrx_be_cpha1(struct spi_device *spi,
+ unsigned nsecs, unsigned cpol,
+ u32 word, u8 bits)
+{
+ /* if (cpol == 0) this is SPI_MODE_1; else this is SPI_MODE_3 */
+
+ /* clock starts at inactive polarity */
+ for (word <<= (32 - bits); likely(bits); bits--) {
+
+ /* setup MSB (to slave) on leading edge */
+ setsck(spi, !cpol);
+ setmosi(spi, word & (1 << 31));
+ spidelay(nsecs); /* T(setup) */
+
+ setsck(spi, cpol);
+ spidelay(nsecs);
+
+ /* sample MSB (from slave) on trailing edge */
+ word <<= 1;
+ word |= getmiso(spi);
+ }
+ return word;
+}
+
+#endif /* EXPAND_BITBANG_TXRX */
