hwmon: (lm90) Add SMBus alert support
Tested successfully with an ADM1032 chip on its evaluation board. It
should work fine with all other chips as well.
At this point this is more of a proof-of-concept, we don't do anything
terribly useful on SMBus alert: we simply log the event. But this could
later evolve into libsensors signaling so that user-space applications
can take an appropriate action.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90
index 08106ad..6a03dd4 100644
--- a/Documentation/hwmon/lm90
+++ b/Documentation/hwmon/lm90
@@ -173,6 +173,18 @@
other second; reading them more often will do no harm, but will return
'old' values.
+SMBus Alert Support
+-------------------
+
+This driver has basic support for SMBus alert. When an alert is received,
+the status register is read and the faulty temperature channel is logged.
+
+The Analog Devices chips (ADM1032 and ADT7461) do not implement the SMBus
+alert protocol properly so additional care is needed: the ALERT output is
+disabled when an alert is received, and is re-enabled only when the alarm
+is gone. Otherwise the chip would block alerts from other chips in the bus
+as long as the alarm is active.
+
PEC Support
-----------
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index 4cbbf15..7cc2708 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -152,6 +152,7 @@
static int lm90_probe(struct i2c_client *client,
const struct i2c_device_id *id);
static void lm90_init_client(struct i2c_client *client);
+static void lm90_alert(struct i2c_client *client, unsigned int flag);
static int lm90_remove(struct i2c_client *client);
static struct lm90_data *lm90_update_device(struct device *dev);
@@ -186,6 +187,7 @@
},
.probe = lm90_probe,
.remove = lm90_remove,
+ .alert = lm90_alert,
.id_table = lm90_id,
.detect = lm90_detect,
.address_list = normal_i2c,
@@ -204,6 +206,7 @@
int flags;
u8 config_orig; /* Original configuration register value */
+ u8 alert_alarms; /* Which alarm bits trigger ALERT# */
/* registers values */
s8 temp8[4]; /* 0: local low limit
@@ -806,6 +809,19 @@
new_client->flags &= ~I2C_CLIENT_PEC;
}
+ /* Different devices have different alarm bits triggering the
+ * ALERT# output */
+ switch (data->kind) {
+ case lm90:
+ case lm99:
+ case lm86:
+ data->alert_alarms = 0x7b;
+ break;
+ default:
+ data->alert_alarms = 0x7c;
+ break;
+ }
+
/* Initialize the LM90 chip */
lm90_init_client(new_client);
@@ -895,6 +911,38 @@
return 0;
}
+static void lm90_alert(struct i2c_client *client, unsigned int flag)
+{
+ struct lm90_data *data = i2c_get_clientdata(client);
+ u8 config, alarms;
+
+ lm90_read_reg(client, LM90_REG_R_STATUS, &alarms);
+ if ((alarms & 0x7f) == 0) {
+ dev_info(&client->dev, "Everything OK\n");
+ } else {
+ if (alarms & 0x61)
+ dev_warn(&client->dev,
+ "temp%d out of range, please check!\n", 1);
+ if (alarms & 0x1a)
+ dev_warn(&client->dev,
+ "temp%d out of range, please check!\n", 2);
+ if (alarms & 0x04)
+ dev_warn(&client->dev,
+ "temp%d diode open, please check!\n", 2);
+
+ /* Disable ALERT# output, because these chips don't implement
+ SMBus alert correctly; they should only hold the alert line
+ low briefly. */
+ if ((data->kind == adm1032 || data->kind == adt7461)
+ && (alarms & data->alert_alarms)) {
+ dev_dbg(&client->dev, "Disabling ALERT#\n");
+ lm90_read_reg(client, LM90_REG_R_CONFIG1, &config);
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
+ config | 0x80);
+ }
+ }
+}
+
static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value)
{
int err;
@@ -982,6 +1030,21 @@
}
lm90_read_reg(client, LM90_REG_R_STATUS, &data->alarms);
+ /* Re-enable ALERT# output if it was originally enabled and
+ * relevant alarms are all clear */
+ if ((data->config_orig & 0x80) == 0
+ && (data->alarms & data->alert_alarms) == 0) {
+ u8 config;
+
+ lm90_read_reg(client, LM90_REG_R_CONFIG1, &config);
+ if (config & 0x80) {
+ dev_dbg(&client->dev, "Re-enabling ALERT#\n");
+ i2c_smbus_write_byte_data(client,
+ LM90_REG_W_CONFIG1,
+ config & ~0x80);
+ }
+ }
+
data->last_updated = jiffies;
data->valid = 1;
}
