[ARM] 5288/1: [AT91] Remove SMC configuration from devices.c files
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
diff --git a/arch/arm/mach-at91/at91sam9260_devices.c b/arch/arm/mach-at91/at91sam9260_devices.c
index 7774d17..fdde1ea 100644
--- a/arch/arm/mach-at91/at91sam9260_devices.c
+++ b/arch/arm/mach-at91/at91sam9260_devices.c
@@ -313,7 +313,7 @@
void __init at91_add_device_nand(struct atmel_nand_data *data)
{
- unsigned long csa, mode;
+ unsigned long csa;
if (!data)
return;
@@ -321,42 +321,6 @@
csa = at91_sys_read(AT91_MATRIX_EBICSA);
at91_sys_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_CS3A_SMC_SMARTMEDIA);
- if (cpu_is_at91sam9260()) {
- /* Timing for sam9260 */
- /* set the bus interface characteristics */
- at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0)
- | AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
-
- at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3)
- | AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
-
- at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(5) | AT91_SMC_NRDCYCLE_(5));
-
- if (data->bus_width_16)
- mode = AT91_SMC_DBW_16;
- else
- mode = AT91_SMC_DBW_8;
- at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(2));
- }
-
- if (cpu_is_at91sam9g20()) {
- /* Timing for sam9g20 */
- /* set the bus interface characteristics */
- at91_sys_write(AT91_SMC_SETUP(3), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0)
- | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
-
- at91_sys_write(AT91_SMC_PULSE(3), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(4)
- | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(4));
-
- at91_sys_write(AT91_SMC_CYCLE(3), AT91_SMC_NWECYCLE_(7) | AT91_SMC_NRDCYCLE_(7));
-
- if (data->bus_width_16)
- mode = AT91_SMC_DBW_16;
- else
- mode = AT91_SMC_DBW_8;
- at91_sys_write(AT91_SMC_MODE(3), mode | AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_TDF_(3));
- }
-
/* enable pin */
if (data->enable_pin)
at91_set_gpio_output(data->enable_pin, 1);
