/*
 * TI DA850/OMAP-L138 EVM board
 *
 * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com/
 *
 * Derived from: arch/arm/mach-davinci/board-da830-evm.c
 * Original Copyrights follow:
 *
 * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
 * the terms of the GNU General Public License version 2. This program
 * is licensed "as is" without any warranty of any kind, whether express
 * or implied.
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/i2c.h>
#include <linux/i2c/at24.h>
#include <linux/i2c/pca953x.h>
#include <linux/mfd/tps6507x.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/tps6507x.h>
#include <linux/mfd/tps6507x.h>
#include <linux/input/tps6507x-ts.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>

#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
#include <mach/mux.h>

#define DA850_EVM_PHY_MASK		0x1
#define DA850_EVM_MDIO_FREQUENCY	2200000 /* PHY bus frequency */

#define DA850_LCD_PWR_PIN		GPIO_TO_PIN(2, 8)
#define DA850_LCD_BL_PIN		GPIO_TO_PIN(2, 15)

#define DA850_MMCSD_CD_PIN		GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN		GPIO_TO_PIN(4, 1)

#define DA850_MII_MDIO_CLKEN_PIN	GPIO_TO_PIN(2, 6)

static struct mtd_partition da850_evm_norflash_partition[] = {
	{
		.name           = "bootloaders + env",
		.offset         = 0,
		.size           = SZ_512K,
		.mask_flags     = MTD_WRITEABLE,
	},
	{
		.name           = "kernel",
		.offset         = MTDPART_OFS_APPEND,
		.size           = SZ_2M,
		.mask_flags     = 0,
	},
	{
		.name           = "filesystem",
		.offset         = MTDPART_OFS_APPEND,
		.size           = MTDPART_SIZ_FULL,
		.mask_flags     = 0,
	},
};

static struct physmap_flash_data da850_evm_norflash_data = {
	.width		= 2,
	.parts		= da850_evm_norflash_partition,
	.nr_parts	= ARRAY_SIZE(da850_evm_norflash_partition),
};

static struct resource da850_evm_norflash_resource[] = {
	{
		.start	= DA8XX_AEMIF_CS2_BASE,
		.end	= DA8XX_AEMIF_CS2_BASE + SZ_32M - 1,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device da850_evm_norflash_device = {
	.name		= "physmap-flash",
	.id		= 0,
	.dev		= {
		.platform_data  = &da850_evm_norflash_data,
	},
	.num_resources	= 1,
	.resource	= da850_evm_norflash_resource,
};

static struct davinci_pm_config da850_pm_pdata = {
	.sleepcount = 128,
};

static struct platform_device da850_pm_device = {
	.name           = "pm-davinci",
	.dev = {
		.platform_data	= &da850_pm_pdata,
	},
	.id             = -1,
};

/* DA850/OMAP-L138 EVM includes a 512 MByte large-page NAND flash
 * (128K blocks). It may be used instead of the (default) SPI flash
 * to boot, using TI's tools to install the secondary boot loader
 * (UBL) and U-Boot.
 */
struct mtd_partition da850_evm_nandflash_partition[] = {
	{
		.name		= "u-boot env",
		.offset		= 0,
		.size		= SZ_128K,
		.mask_flags	= MTD_WRITEABLE,
	 },
	{
		.name		= "UBL",
		.offset		= MTDPART_OFS_APPEND,
		.size		= SZ_128K,
		.mask_flags	= MTD_WRITEABLE,
	},
	{
		.name		= "u-boot",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 4 * SZ_128K,
		.mask_flags	= MTD_WRITEABLE,
	},
	{
		.name		= "kernel",
		.offset		= 0x200000,
		.size		= SZ_2M,
		.mask_flags	= 0,
	},
	{
		.name		= "filesystem",
		.offset		= MTDPART_OFS_APPEND,
		.size		= MTDPART_SIZ_FULL,
		.mask_flags	= 0,
	},
};

static struct davinci_nand_pdata da850_evm_nandflash_data = {
	.parts		= da850_evm_nandflash_partition,
	.nr_parts	= ARRAY_SIZE(da850_evm_nandflash_partition),
	.ecc_mode	= NAND_ECC_HW,
	.ecc_bits	= 4,
	.options	= NAND_USE_FLASH_BBT,
};

static struct resource da850_evm_nandflash_resource[] = {
	{
		.start	= DA8XX_AEMIF_CS3_BASE,
		.end	= DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
		.flags	= IORESOURCE_MEM,
	},
	{
		.start	= DA8XX_AEMIF_CTL_BASE,
		.end	= DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
		.flags	= IORESOURCE_MEM,
	},
};

static struct platform_device da850_evm_nandflash_device = {
	.name		= "davinci_nand",
	.id		= 1,
	.dev		= {
		.platform_data	= &da850_evm_nandflash_data,
	},
	.num_resources	= ARRAY_SIZE(da850_evm_nandflash_resource),
	.resource	= da850_evm_nandflash_resource,
};

static struct platform_device *da850_evm_devices[] __initdata = {
	&da850_evm_nandflash_device,
	&da850_evm_norflash_device,
};

#define DA8XX_AEMIF_CE2CFG_OFFSET	0x10
#define DA8XX_AEMIF_ASIZE_16BIT		0x1

static void __init da850_evm_init_nor(void)
{
	void __iomem *aemif_addr;

	aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K);

	/* Configure data bus width of CS2 to 16 bit */
	writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) |
		DA8XX_AEMIF_ASIZE_16BIT,
		aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET);

	iounmap(aemif_addr);
}

static u32 ui_card_detected;

#if defined(CONFIG_MMC_DAVINCI) || \
    defined(CONFIG_MMC_DAVINCI_MODULE)
#define HAS_MMC 1
#else
#define HAS_MMC 0
#endif

static __init void da850_evm_setup_nor_nand(void)
{
	int ret = 0;

	if (ui_card_detected & !HAS_MMC) {
		ret = davinci_cfg_reg_list(da850_nand_pins);
		if (ret)
			pr_warning("da850_evm_init: nand mux setup failed: "
					"%d\n", ret);

		ret = davinci_cfg_reg_list(da850_nor_pins);
		if (ret)
			pr_warning("da850_evm_init: nor mux setup failed: %d\n",
				ret);

		da850_evm_init_nor();

		platform_add_devices(da850_evm_devices,
					ARRAY_SIZE(da850_evm_devices));
	}
}

#ifdef CONFIG_DA850_UI_RMII
static inline void da850_evm_setup_emac_rmii(int rmii_sel)
{
	struct davinci_soc_info *soc_info = &davinci_soc_info;

	soc_info->emac_pdata->rmii_en = 1;
	gpio_set_value(rmii_sel, 0);
}
#else
static inline void da850_evm_setup_emac_rmii(int rmii_sel) { }
#endif

static int da850_evm_ui_expander_setup(struct i2c_client *client, unsigned gpio,
						unsigned ngpio, void *c)
{
	int sel_a, sel_b, sel_c, ret;

	sel_a = gpio + 7;
	sel_b = gpio + 6;
	sel_c = gpio + 5;

	ret = gpio_request(sel_a, "sel_a");
	if (ret) {
		pr_warning("Cannot open UI expander pin %d\n", sel_a);
		goto exp_setup_sela_fail;
	}

	ret = gpio_request(sel_b, "sel_b");
	if (ret) {
		pr_warning("Cannot open UI expander pin %d\n", sel_b);
		goto exp_setup_selb_fail;
	}

	ret = gpio_request(sel_c, "sel_c");
	if (ret) {
		pr_warning("Cannot open UI expander pin %d\n", sel_c);
		goto exp_setup_selc_fail;
	}

	/* deselect all functionalities */
	gpio_direction_output(sel_a, 1);
	gpio_direction_output(sel_b, 1);
	gpio_direction_output(sel_c, 1);

	ui_card_detected = 1;
	pr_info("DA850/OMAP-L138 EVM UI card detected\n");

	da850_evm_setup_nor_nand();

	da850_evm_setup_emac_rmii(sel_a);

	return 0;

exp_setup_selc_fail:
	gpio_free(sel_b);
exp_setup_selb_fail:
	gpio_free(sel_a);
exp_setup_sela_fail:
	return ret;
}

static int da850_evm_ui_expander_teardown(struct i2c_client *client,
					unsigned gpio, unsigned ngpio, void *c)
{
	/* deselect all functionalities */
	gpio_set_value(gpio + 5, 1);
	gpio_set_value(gpio + 6, 1);
	gpio_set_value(gpio + 7, 1);

	gpio_free(gpio + 5);
	gpio_free(gpio + 6);
	gpio_free(gpio + 7);

	return 0;
}

static struct pca953x_platform_data da850_evm_ui_expander_info = {
	.gpio_base	= DAVINCI_N_GPIO,
	.setup		= da850_evm_ui_expander_setup,
	.teardown	= da850_evm_ui_expander_teardown,
};

static struct i2c_board_info __initdata da850_evm_i2c_devices[] = {
	{
		I2C_BOARD_INFO("tlv320aic3x", 0x18),
	},
	{
		I2C_BOARD_INFO("tca6416", 0x20),
		.platform_data = &da850_evm_ui_expander_info,
	},
};

static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = {
	.bus_freq	= 100,	/* kHz */
	.bus_delay	= 0,	/* usec */
};

static struct davinci_uart_config da850_evm_uart_config __initdata = {
	.enabled_uarts = 0x7,
};

/* davinci da850 evm audio machine driver */
static u8 da850_iis_serializer_direction[] = {
	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	TX_MODE,
	RX_MODE,	INACTIVE_MODE,	INACTIVE_MODE,	INACTIVE_MODE,
};

static struct snd_platform_data da850_evm_snd_data = {
	.tx_dma_offset	= 0x2000,
	.rx_dma_offset	= 0x2000,
	.op_mode	= DAVINCI_MCASP_IIS_MODE,
	.num_serializer	= ARRAY_SIZE(da850_iis_serializer_direction),
	.tdm_slots	= 2,
	.serial_dir	= da850_iis_serializer_direction,
	.asp_chan_q	= EVENTQ_1,
	.version	= MCASP_VERSION_2,
	.txnumevt	= 1,
	.rxnumevt	= 1,
};

static int da850_evm_mmc_get_ro(int index)
{
	return gpio_get_value(DA850_MMCSD_WP_PIN);
}

static int da850_evm_mmc_get_cd(int index)
{
	return !gpio_get_value(DA850_MMCSD_CD_PIN);
}

static struct davinci_mmc_config da850_mmc_config = {
	.get_ro		= da850_evm_mmc_get_ro,
	.get_cd		= da850_evm_mmc_get_cd,
	.wires		= 4,
	.max_freq	= 50000000,
	.caps		= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
	.version	= MMC_CTLR_VERSION_2,
};

static void da850_panel_power_ctrl(int val)
{
	/* lcd backlight */
	gpio_set_value(DA850_LCD_BL_PIN, val);

	/* lcd power */
	gpio_set_value(DA850_LCD_PWR_PIN, val);
}

static int da850_lcd_hw_init(void)
{
	int status;

	status = gpio_request(DA850_LCD_BL_PIN, "lcd bl\n");
	if (status < 0)
		return status;

	status = gpio_request(DA850_LCD_PWR_PIN, "lcd pwr\n");
	if (status < 0) {
		gpio_free(DA850_LCD_BL_PIN);
		return status;
	}

	gpio_direction_output(DA850_LCD_BL_PIN, 0);
	gpio_direction_output(DA850_LCD_PWR_PIN, 0);

	/* Switch off panel power and backlight */
	da850_panel_power_ctrl(0);

	/* Switch on panel power and backlight */
	da850_panel_power_ctrl(1);

	return 0;
}

/* TPS65070 voltage regulator support */

/* 3.3V */
struct regulator_consumer_supply tps65070_dcdc1_consumers[] = {
	{
		.supply = "usb0_vdda33",
	},
	{
		.supply = "usb1_vdda33",
	},
};

/* 3.3V or 1.8V */
struct regulator_consumer_supply tps65070_dcdc2_consumers[] = {
	{
		.supply = "dvdd3318_a",
	},
	{
		.supply = "dvdd3318_b",
	},
	{
		.supply = "dvdd3318_c",
	},
};

/* 1.2V */
struct regulator_consumer_supply tps65070_dcdc3_consumers[] = {
	{
		.supply = "cvdd",
	},
};

/* 1.8V LDO */
struct regulator_consumer_supply tps65070_ldo1_consumers[] = {
	{
		.supply = "sata_vddr",
	},
	{
		.supply = "usb0_vdda18",
	},
	{
		.supply = "usb1_vdda18",
	},
	{
		.supply = "ddr_dvdd18",
	},
};

/* 1.2V LDO */
struct regulator_consumer_supply tps65070_ldo2_consumers[] = {
	{
		.supply = "sata_vdd",
	},
	{
		.supply = "pll0_vdda",
	},
	{
		.supply = "pll1_vdda",
	},
	{
		.supply = "usbs_cvdd",
	},
	{
		.supply = "vddarnwa1",
	},
};

/* We take advantage of the fact that both defdcdc{2,3} are tied high */
static struct tps6507x_reg_platform_data tps6507x_platform_data = {
	.defdcdc_default = true,
};

struct regulator_init_data tps65070_regulator_data[] = {
	/* dcdc1 */
	{
		.constraints = {
			.min_uV = 3150000,
			.max_uV = 3450000,
			.valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
				REGULATOR_CHANGE_STATUS),
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc1_consumers),
		.consumer_supplies = tps65070_dcdc1_consumers,
	},

	/* dcdc2 */
	{
		.constraints = {
			.min_uV = 1710000,
			.max_uV = 3450000,
			.valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
				REGULATOR_CHANGE_STATUS),
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc2_consumers),
		.consumer_supplies = tps65070_dcdc2_consumers,
		.driver_data = &tps6507x_platform_data,
	},

	/* dcdc3 */
	{
		.constraints = {
			.min_uV = 950000,
			.max_uV = 1320000,
			.valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
				REGULATOR_CHANGE_STATUS),
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65070_dcdc3_consumers),
		.consumer_supplies = tps65070_dcdc3_consumers,
		.driver_data = &tps6507x_platform_data,
	},

	/* ldo1 */
	{
		.constraints = {
			.min_uV = 1710000,
			.max_uV = 1890000,
			.valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
				REGULATOR_CHANGE_STATUS),
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65070_ldo1_consumers),
		.consumer_supplies = tps65070_ldo1_consumers,
	},

	/* ldo2 */
	{
		.constraints = {
			.min_uV = 1140000,
			.max_uV = 1320000,
			.valid_ops_mask = (REGULATOR_CHANGE_VOLTAGE |
				REGULATOR_CHANGE_STATUS),
			.boot_on = 1,
		},
		.num_consumer_supplies = ARRAY_SIZE(tps65070_ldo2_consumers),
		.consumer_supplies = tps65070_ldo2_consumers,
	},
};

static struct touchscreen_init_data tps6507x_touchscreen_data = {
	.poll_period =  30,	/* ms between touch samples */
	.min_pressure = 0x30,	/* minimum pressure to trigger touch */
	.vref = 0,		/* turn off vref when not using A/D */
	.vendor = 0,		/* /sys/class/input/input?/id/vendor */
	.product = 65070,	/* /sys/class/input/input?/id/product */
	.version = 0x100,	/* /sys/class/input/input?/id/version */
};

static struct tps6507x_board tps_board = {
	.tps6507x_pmic_init_data = &tps65070_regulator_data[0],
	.tps6507x_ts_init_data = &tps6507x_touchscreen_data,
};

static struct i2c_board_info __initdata da850evm_tps65070_info[] = {
	{
		I2C_BOARD_INFO("tps6507x", 0x48),
		.platform_data = &tps_board,
	},
};

static int __init pmic_tps65070_init(void)
{
	return i2c_register_board_info(1, da850evm_tps65070_info,
					ARRAY_SIZE(da850evm_tps65070_info));
}

static const short da850_evm_lcdc_pins[] = {
	DA850_GPIO2_8, DA850_GPIO2_15,
	-1
};

static int __init da850_evm_config_emac(void)
{
	void __iomem *cfg_chip3_base;
	int ret;
	u32 val;
	struct davinci_soc_info *soc_info = &davinci_soc_info;
	u8 rmii_en = soc_info->emac_pdata->rmii_en;

	if (!machine_is_davinci_da850_evm())
		return 0;

	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);

	val = __raw_readl(cfg_chip3_base);

	if (rmii_en) {
		val |= BIT(8);
		ret = davinci_cfg_reg_list(da850_rmii_pins);
		pr_info("EMAC: RMII PHY configured, MII PHY will not be"
							" functional\n");
	} else {
		val &= ~BIT(8);
		ret = davinci_cfg_reg_list(da850_cpgmac_pins);
		pr_info("EMAC: MII PHY configured, RMII PHY will not be"
							" functional\n");
	}

	if (ret)
		pr_warning("da850_evm_init: cpgmac/rmii mux setup failed: %d\n",
				ret);

	/* configure the CFGCHIP3 register for RMII or MII */
	__raw_writel(val, cfg_chip3_base);

	ret = davinci_cfg_reg(DA850_GPIO2_6);
	if (ret)
		pr_warning("da850_evm_init:GPIO(2,6) mux setup "
							"failed\n");

	ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en");
	if (ret) {
		pr_warning("Cannot open GPIO %d\n",
					DA850_MII_MDIO_CLKEN_PIN);
		return ret;
	}

	/* Enable/Disable MII MDIO clock */
	gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en);

	soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK;
	soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY;

	ret = da8xx_register_emac();
	if (ret)
		pr_warning("da850_evm_init: emac registration failed: %d\n",
				ret);

	return 0;
}
device_initcall(da850_evm_config_emac);

/*
 * The following EDMA channels/slots are not being used by drivers (for
 * example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM, hence
 * they are being reserved for codecs on the DSP side.
 */
static const s16 da850_dma0_rsv_chans[][2] = {
	/* (offset, number) */
	{ 8,  6},
	{24,  4},
	{30,  2},
	{-1, -1}
};

static const s16 da850_dma0_rsv_slots[][2] = {
	/* (offset, number) */
	{ 8,  6},
	{24,  4},
	{30, 50},
	{-1, -1}
};

static const s16 da850_dma1_rsv_chans[][2] = {
	/* (offset, number) */
	{ 0, 28},
	{30,  2},
	{-1, -1}
};

static const s16 da850_dma1_rsv_slots[][2] = {
	/* (offset, number) */
	{ 0, 28},
	{30, 90},
	{-1, -1}
};

static struct edma_rsv_info da850_edma_cc0_rsv = {
	.rsv_chans	= da850_dma0_rsv_chans,
	.rsv_slots	= da850_dma0_rsv_slots,
};

static struct edma_rsv_info da850_edma_cc1_rsv = {
	.rsv_chans	= da850_dma1_rsv_chans,
	.rsv_slots	= da850_dma1_rsv_slots,
};

static struct edma_rsv_info *da850_edma_rsv[2] = {
	&da850_edma_cc0_rsv,
	&da850_edma_cc1_rsv,
};

static __init void da850_evm_init(void)
{
	int ret;

	ret = pmic_tps65070_init();
	if (ret)
		pr_warning("da850_evm_init: TPS65070 PMIC init failed: %d\n",
				ret);

	ret = da850_register_edma(da850_edma_rsv);
	if (ret)
		pr_warning("da850_evm_init: edma registration failed: %d\n",
				ret);

	ret = davinci_cfg_reg_list(da850_i2c0_pins);
	if (ret)
		pr_warning("da850_evm_init: i2c0 mux setup failed: %d\n",
				ret);

	ret = da8xx_register_i2c(0, &da850_evm_i2c_0_pdata);
	if (ret)
		pr_warning("da850_evm_init: i2c0 registration failed: %d\n",
				ret);


	ret = da8xx_register_watchdog();
	if (ret)
		pr_warning("da830_evm_init: watchdog registration failed: %d\n",
				ret);

	if (HAS_MMC) {
		ret = davinci_cfg_reg_list(da850_mmcsd0_pins);
		if (ret)
			pr_warning("da850_evm_init: mmcsd0 mux setup failed:"
					" %d\n", ret);

		ret = gpio_request(DA850_MMCSD_CD_PIN, "MMC CD\n");
		if (ret)
			pr_warning("da850_evm_init: can not open GPIO %d\n",
					DA850_MMCSD_CD_PIN);
		gpio_direction_input(DA850_MMCSD_CD_PIN);

		ret = gpio_request(DA850_MMCSD_WP_PIN, "MMC WP\n");
		if (ret)
			pr_warning("da850_evm_init: can not open GPIO %d\n",
					DA850_MMCSD_WP_PIN);
		gpio_direction_input(DA850_MMCSD_WP_PIN);

		ret = da8xx_register_mmcsd0(&da850_mmc_config);
		if (ret)
			pr_warning("da850_evm_init: mmcsd0 registration failed:"
					" %d\n", ret);
	}

	davinci_serial_init(&da850_evm_uart_config);

	i2c_register_board_info(1, da850_evm_i2c_devices,
			ARRAY_SIZE(da850_evm_i2c_devices));

	/*
	 * shut down uart 0 and 1; they are not used on the board and
	 * accessing them causes endless "too much work in irq53" messages
	 * with arago fs
	 */
	__raw_writel(0, IO_ADDRESS(DA8XX_UART1_BASE) + 0x30);
	__raw_writel(0, IO_ADDRESS(DA8XX_UART0_BASE) + 0x30);

	ret = davinci_cfg_reg_list(da850_mcasp_pins);
	if (ret)
		pr_warning("da850_evm_init: mcasp mux setup failed: %d\n",
				ret);

	da8xx_register_mcasp(0, &da850_evm_snd_data);

	ret = davinci_cfg_reg_list(da850_lcdcntl_pins);
	if (ret)
		pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n",
				ret);

	/* Handle board specific muxing for LCD here */
	ret = davinci_cfg_reg_list(da850_evm_lcdc_pins);
	if (ret)
		pr_warning("da850_evm_init: evm specific lcd mux setup "
				"failed: %d\n",	ret);

	ret = da850_lcd_hw_init();
	if (ret)
		pr_warning("da850_evm_init: lcd initialization failed: %d\n",
				ret);

	sharp_lk043t1dg01_pdata.panel_power_ctrl = da850_panel_power_ctrl,
	ret = da8xx_register_lcdc(&sharp_lk043t1dg01_pdata);
	if (ret)
		pr_warning("da850_evm_init: lcdc registration failed: %d\n",
				ret);

	ret = da8xx_register_rtc();
	if (ret)
		pr_warning("da850_evm_init: rtc setup failed: %d\n", ret);

	ret = da850_register_cpufreq();
	if (ret)
		pr_warning("da850_evm_init: cpufreq registration failed: %d\n",
				ret);

	ret = da8xx_register_cpuidle();
	if (ret)
		pr_warning("da850_evm_init: cpuidle registration failed: %d\n",
				ret);

	ret = da850_register_pm(&da850_pm_device);
	if (ret)
		pr_warning("da850_evm_init: suspend registration failed: %d\n",
				ret);
}

#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da850_evm_console_init(void)
{
	return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da850_evm_console_init);
#endif

static void __init da850_evm_map_io(void)
{
	da850_init();
}

MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM")
	.phys_io	= IO_PHYS,
	.io_pg_offst	= (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
	.boot_params	= (DA8XX_DDR_BASE + 0x100),
	.map_io		= da850_evm_map_io,
	.init_irq	= cp_intc_init,
	.timer		= &davinci_timer,
	.init_machine	= da850_evm_init,
MACHINE_END