/*
 * Edgeport USB Serial Converter driver
 *
 * Copyright (C) 2000-2002 Inside Out Networks, All rights reserved.
 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com>
 *
 *	This program is free software; you can redistribute it and/or modify
 *	it under the terms of the GNU General Public License as published by
 *	the Free Software Foundation; either version 2 of the License, or
 *	(at your option) any later version.
 *
 * Supports the following devices:
 *	EP/1 EP/2 EP/4 EP/21 EP/22 EP/221 EP/42 EP/421 WATCHPORT
 *
 * For questions or problems with this driver, contact Inside Out
 * Networks technical support, or Peter Berger <pberger@brimson.com>,
 * or Al Borchers <alborchers@steinerpoint.com>.
 *
 * Version history:
 *
 *	July 11, 2002 	Removed 4 port device structure since all TI UMP 
 *			chips have only 2 ports 
 *			David Iacovelli (davidi@ionetworks.com)
 *
 */

#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/jiffies.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_driver.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/serial.h>
#include <linux/ioctl.h>
#include <asm/uaccess.h>
#include <asm/semaphore.h>
#include <linux/usb.h>

#include "usb-serial.h"
#include "io_16654.h"
#include "io_usbvend.h"
#include "io_ti.h"

/*
 * Version Information
 */
#define DRIVER_VERSION "v0.7"
#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli"
#define DRIVER_DESC "Edgeport USB Serial Driver"


/* firmware image code */
#define IMAGE_VERSION_NAME	PagableOperationalCodeImageVersion
#define IMAGE_ARRAY_NAME	PagableOperationalCodeImage
#define IMAGE_SIZE		PagableOperationalCodeSize
#include "io_fw_down3.h"	/* Define array OperationalCodeImage[] */

#define EPROM_PAGE_SIZE		64


struct edgeport_uart_buf_desc {
	__u32 count;		// Number of bytes currently in buffer
};

/* different hardware types */
#define HARDWARE_TYPE_930	0
#define HARDWARE_TYPE_TIUMP	1

// IOCTL_PRIVATE_TI_GET_MODE Definitions
#define	TI_MODE_CONFIGURING	0   // Device has not entered start device 
#define	TI_MODE_BOOT		1   // Staying in boot mode
#define TI_MODE_DOWNLOAD	2   // Made it to download mode
#define TI_MODE_TRANSITIONING	3   // Currently in boot mode but transitioning to download mode

/* read urb state */
#define EDGE_READ_URB_RUNNING	0
#define EDGE_READ_URB_STOPPING	1
#define EDGE_READ_URB_STOPPED	2

#define EDGE_LOW_LATENCY	1
#define EDGE_CLOSING_WAIT	4000	/* in .01 sec */

#define EDGE_OUT_BUF_SIZE	1024


/* Product information read from the Edgeport */
struct product_info
{
	int	TiMode;			// Current TI Mode
	__u8	hardware_type;		// Type of hardware
} __attribute__((packed));

/* circular buffer */
struct edge_buf {
	unsigned int	buf_size;
	char		*buf_buf;
	char		*buf_get;
	char		*buf_put;
};

struct edgeport_port {
	__u16 uart_base;
	__u16 dma_address;
	__u8 shadow_msr;
	__u8 shadow_mcr;
	__u8 shadow_lsr;
	__u8 lsr_mask;
	__u32 ump_read_timeout;		/* Number of miliseconds the UMP will
					   wait without data before completing
					   a read short */
	int baud_rate;
	int close_pending;
	int lsr_event;
	struct edgeport_uart_buf_desc tx;
	struct async_icount	icount;
	wait_queue_head_t	delta_msr_wait;	/* for handling sleeping while
						   waiting for msr change to
						   happen */
	struct edgeport_serial	*edge_serial;
	struct usb_serial_port	*port;
	__u8 bUartMode;		/* Port type, 0: RS232, etc. */ 
	spinlock_t ep_lock;
	int ep_read_urb_state;
	int ep_write_urb_in_use;
	struct edge_buf *ep_out_buf;
};

struct edgeport_serial {
	struct product_info product_info;
	u8 TI_I2C_Type;			// Type of I2C in UMP
	u8 TiReadI2C;			// Set to TRUE if we have read the I2c in Boot Mode
	struct semaphore es_sem;
	int num_ports_open;
	struct usb_serial *serial;
};


/* Devices that this driver supports */
static struct usb_device_id edgeport_1port_id_table [] = {
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
	{ }
};

static struct usb_device_id edgeport_2port_id_table [] = {
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
// The 4-port shows up as two 2-port devices
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
	{ }
};

/* Devices that this driver supports */
static struct usb_device_id id_table_combined [] = {
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) },
	{ USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) },
	{ }
};

MODULE_DEVICE_TABLE (usb, id_table_combined);

static struct usb_driver io_driver = {
	.name =		"io_ti",
	.probe =	usb_serial_probe,
	.disconnect =	usb_serial_disconnect,
	.id_table =	id_table_combined,
	.no_dynamic_id = 	1,
};


static struct EDGE_FIRMWARE_VERSION_INFO OperationalCodeImageVersion;

static int debug;

static int TIStayInBootMode = 0;
static int low_latency = EDGE_LOW_LATENCY;
static int closing_wait = EDGE_CLOSING_WAIT;
static int ignore_cpu_rev = 0;


static void edge_tty_recv(struct device *dev, struct tty_struct *tty, unsigned char *data, int length);

static void stop_read(struct edgeport_port *edge_port);
static int restart_read(struct edgeport_port *edge_port);

static void edge_set_termios (struct usb_serial_port *port, struct termios *old_termios);
static void edge_send(struct usb_serial_port *port);

/* circular buffer */
static struct edge_buf *edge_buf_alloc(unsigned int size);
static void edge_buf_free(struct edge_buf *eb);
static void edge_buf_clear(struct edge_buf *eb);
static unsigned int edge_buf_data_avail(struct edge_buf *eb);
static unsigned int edge_buf_space_avail(struct edge_buf *eb);
static unsigned int edge_buf_put(struct edge_buf *eb, const char *buf,
	unsigned int count);
static unsigned int edge_buf_get(struct edge_buf *eb, char *buf,
	unsigned int count);


static int TIReadVendorRequestSync (struct usb_device *dev,
				__u8		request,
				__u16		value,
				__u16		index,
				u8 		*data,
				int		size)
{
	int status;

	status = usb_control_msg (dev,
				usb_rcvctrlpipe(dev, 0),
				request,
				(USB_TYPE_VENDOR | 
				 USB_RECIP_DEVICE | 
				 USB_DIR_IN),
				value,
				index,
				data,
				size,
				1000);
	if (status < 0)
		return status;
	if (status != size) {
		dbg ("%s - wanted to write %d, but only wrote %d",
		     __FUNCTION__, size, status);
		return -ECOMM;
	}
	return 0;
}

static int TISendVendorRequestSync (struct usb_device *dev,
				__u8		request,
				__u16		value,
				__u16		index,
				u8 		*data,
				int		size)
{
	int status;

	status = usb_control_msg (dev,
				usb_sndctrlpipe(dev, 0),
				request,
				(USB_TYPE_VENDOR | 
				 USB_RECIP_DEVICE | 
				 USB_DIR_OUT),
				value,
				index,
				data,
				size,
				1000);
	if (status < 0)
		return status;
	if (status != size) {
		dbg ("%s - wanted to write %d, but only wrote %d",
		     __FUNCTION__, size, status);
		return -ECOMM;
	}
	return 0;
}

static int TIWriteCommandSync (struct usb_device *dev, __u8 command,
				__u8 moduleid, __u16 value, u8 *data,
				int size)
{
	return TISendVendorRequestSync (dev,
					  command,	  		// Request
					  value,			// wValue 
					  moduleid,			// wIndex
					  data,				// TransferBuffer
					  size);			// TransferBufferLength

}

/* clear tx/rx buffers and fifo in TI UMP */
static int TIPurgeDataSync (struct usb_serial_port *port, __u16 mask)
{
	int port_number = port->number - port->serial->minor;

	dbg ("%s - port %d, mask %x", __FUNCTION__, port_number, mask);

	return TIWriteCommandSync (port->serial->dev,
					UMPC_PURGE_PORT,
					(__u8)(UMPM_UART1_PORT + port_number),
					mask,
					NULL,
					0);
}

/**
 * TIReadDownloadMemory - Read edgeport memory from TI chip
 * @dev: usb device pointer
 * @start_address: Device CPU address at which to read
 * @length: Length of above data
 * @address_type: Can read both XDATA and I2C
 * @buffer: pointer to input data buffer
 */
static int TIReadDownloadMemory(struct usb_device *dev, int start_address,
				int length, __u8 address_type, __u8 *buffer)
{
	int status = 0;
	__u8 read_length;
	__be16 be_start_address;
	
	dbg ("%s - @ %x for %d", __FUNCTION__, start_address, length);

	/* Read in blocks of 64 bytes
	 * (TI firmware can't handle more than 64 byte reads)
	 */
	while (length) {
		if (length > 64)
			read_length= 64;
		else
			read_length = (__u8)length;

		if (read_length > 1) {
			dbg ("%s - @ %x for %d", __FUNCTION__, 
			     start_address, read_length);
		}
		be_start_address = cpu_to_be16 (start_address);
		status = TIReadVendorRequestSync (dev,
						  UMPC_MEMORY_READ,	// Request
						  (__u16)address_type,	// wValue (Address type)
						  (__force __u16)be_start_address,	// wIndex (Address to read)
						  buffer,		// TransferBuffer
						  read_length);	// TransferBufferLength

		if (status) {
			dbg ("%s - ERROR %x", __FUNCTION__, status);
			return status;
		}

		if (read_length > 1) {
			usb_serial_debug_data(debug, &dev->dev, __FUNCTION__,
					      read_length, buffer);
		}

		/* Update pointers/length */
		start_address += read_length;
		buffer += read_length;
		length -= read_length;
	}
	
	return status;
}

static int TIReadRam (struct usb_device *dev, int start_address, int length, __u8 *buffer)
{
	return TIReadDownloadMemory (dev,
				     start_address,
				     length,
				     DTK_ADDR_SPACE_XDATA,
				     buffer);
}

/* Read edgeport memory to a given block */
static int TIReadBootMemory (struct edgeport_serial *serial, int start_address, int length, __u8 * buffer)
{
	int status = 0;
	int i;

	for (i=0; i< length; i++) {
		status = TIReadVendorRequestSync (serial->serial->dev,
					UMPC_MEMORY_READ,		// Request
					serial->TI_I2C_Type,		// wValue (Address type)
					(__u16)(start_address+i),	// wIndex
					&buffer[i],			// TransferBuffer
					0x01);				// TransferBufferLength
		if (status) {
			dbg ("%s - ERROR %x", __FUNCTION__, status);
			return status;
		}
	}

	dbg ("%s - start_address = %x, length = %d", __FUNCTION__, start_address, length);
	usb_serial_debug_data(debug, &serial->serial->dev->dev, __FUNCTION__, length, buffer);

	serial->TiReadI2C = 1;

	return status;
}

/* Write given block to TI EPROM memory */
static int TIWriteBootMemory (struct edgeport_serial *serial, int start_address, int length, __u8 *buffer)
{
	int status = 0;
	int i;
	__u8 temp;

	/* Must do a read before write */
	if (!serial->TiReadI2C) {
		status = TIReadBootMemory(serial, 0, 1, &temp);
		if (status)
			return status;
	}

	for (i=0; i < length; ++i) {
		status = TISendVendorRequestSync (serial->serial->dev,
						UMPC_MEMORY_WRITE,		// Request
						buffer[i],			// wValue
						(__u16)(i+start_address),	// wIndex
						NULL,				// TransferBuffer
						0);				// TransferBufferLength
		if (status)
			return status;
	}

  	dbg ("%s - start_sddr = %x, length = %d", __FUNCTION__, start_address, length);
	usb_serial_debug_data(debug, &serial->serial->dev->dev, __FUNCTION__, length, buffer);

	return status;
}


/* Write edgeport I2C memory to TI chip	*/
static int TIWriteDownloadI2C (struct edgeport_serial *serial, int start_address, int length, __u8 address_type, __u8 *buffer)
{
	int status = 0;
	int write_length;
	__be16 be_start_address;

	/* We can only send a maximum of 1 aligned byte page at a time */
	
	/* calulate the number of bytes left in the first page */
	write_length = EPROM_PAGE_SIZE - (start_address & (EPROM_PAGE_SIZE - 1));

	if (write_length > length)
		write_length = length;

	dbg ("%s - BytesInFirstPage Addr = %x, length = %d", __FUNCTION__, start_address, write_length);
	usb_serial_debug_data(debug, &serial->serial->dev->dev, __FUNCTION__, write_length, buffer);

	/* Write first page */
	be_start_address = cpu_to_be16 (start_address);
	status = TISendVendorRequestSync (serial->serial->dev,
					UMPC_MEMORY_WRITE,	// Request
					(__u16)address_type,	// wValue
					(__force __u16)be_start_address,	// wIndex
					buffer,			// TransferBuffer
					write_length);
	if (status) {
		dbg ("%s - ERROR %d", __FUNCTION__, status);
		return status;
	}

	length		-= write_length;
	start_address	+= write_length;
	buffer		+= write_length;

	/* We should be aligned now -- can write max page size bytes at a time */
	while (length) {
		if (length > EPROM_PAGE_SIZE)
			write_length = EPROM_PAGE_SIZE;
		else
			write_length = length;

		dbg ("%s - Page Write Addr = %x, length = %d", __FUNCTION__, start_address, write_length);
		usb_serial_debug_data(debug, &serial->serial->dev->dev, __FUNCTION__, write_length, buffer);

		/* Write next page */
		be_start_address = cpu_to_be16 (start_address);
		status = TISendVendorRequestSync (serial->serial->dev,
						UMPC_MEMORY_WRITE,	// Request
						(__u16)address_type,	// wValue
						(__force __u16)be_start_address,	// wIndex
						buffer,	  		// TransferBuffer
						write_length);		// TransferBufferLength
		if (status) {
			dev_err (&serial->serial->dev->dev, "%s - ERROR %d\n", __FUNCTION__, status);
			return status;
		}
		
		length		-= write_length;
		start_address	+= write_length;
		buffer		+= write_length;
	}
	return status;
}

/* Examine the UMP DMA registers and LSR
 * 
 * Check the MSBit of the X and Y DMA byte count registers.
 * A zero in this bit indicates that the TX DMA buffers are empty
 * then check the TX Empty bit in the UART.
 */
static int TIIsTxActive (struct edgeport_port *port)
{
	int status;
	struct out_endpoint_desc_block *oedb;
	__u8 *lsr;
	int bytes_left = 0;

	oedb = kmalloc (sizeof (* oedb), GFP_KERNEL);
	if (!oedb) {
		dev_err (&port->port->dev, "%s - out of memory\n", __FUNCTION__);
		return -ENOMEM;
	}

	lsr = kmalloc (1, GFP_KERNEL);	/* Sigh, that's right, just one byte,
					   as not all platforms can do DMA
					   from stack */
	if (!lsr) {
		kfree(oedb);
		return -ENOMEM;
	}
	/* Read the DMA Count Registers */
	status = TIReadRam (port->port->serial->dev,
			    port->dma_address,
			    sizeof( *oedb),
			    (void *)oedb);

	if (status)
		goto exit_is_tx_active;

	dbg ("%s - XByteCount    0x%X", __FUNCTION__, oedb->XByteCount);

	/* and the LSR */
	status = TIReadRam (port->port->serial->dev, 
			    port->uart_base + UMPMEM_OFFS_UART_LSR,
			    1,
			    lsr);

	if (status)
		goto exit_is_tx_active;
	dbg ("%s - LSR = 0x%X", __FUNCTION__, *lsr);
	
	/* If either buffer has data or we are transmitting then return TRUE */
	if ((oedb->XByteCount & 0x80 ) != 0 )
		bytes_left += 64;

	if ((*lsr & UMP_UART_LSR_TX_MASK ) == 0 )
		bytes_left += 1;

	/* We return Not Active if we get any kind of error */
exit_is_tx_active:
	dbg ("%s - return %d", __FUNCTION__, bytes_left );

	kfree(lsr);
	kfree(oedb);
	return bytes_left;
}

static void TIChasePort(struct edgeport_port *port, unsigned long timeout, int flush)
{
	int baud_rate;
	struct tty_struct *tty = port->port->tty;
	wait_queue_t wait;
	unsigned long flags;

	if (!timeout)
		timeout = (HZ*EDGE_CLOSING_WAIT)/100;

	/* wait for data to drain from the buffer */
	spin_lock_irqsave(&port->ep_lock, flags);
	init_waitqueue_entry(&wait, current);
	add_wait_queue(&tty->write_wait, &wait);
	for (;;) {
		set_current_state(TASK_INTERRUPTIBLE);
		if (edge_buf_data_avail(port->ep_out_buf) == 0
		|| timeout == 0 || signal_pending(current)
		|| !usb_get_intfdata(port->port->serial->interface))  /* disconnect */
			break;
		spin_unlock_irqrestore(&port->ep_lock, flags);
		timeout = schedule_timeout(timeout);
		spin_lock_irqsave(&port->ep_lock, flags);
	}
	set_current_state(TASK_RUNNING);
	remove_wait_queue(&tty->write_wait, &wait);
	if (flush)
		edge_buf_clear(port->ep_out_buf);
	spin_unlock_irqrestore(&port->ep_lock, flags);

	/* wait for data to drain from the device */
	timeout += jiffies;
	while ((long)(jiffies - timeout) < 0 && !signal_pending(current)
	&& usb_get_intfdata(port->port->serial->interface)) {  /* not disconnected */
		if (!TIIsTxActive(port))
			break;
		msleep(10);
	}

	/* disconnected */
	if (!usb_get_intfdata(port->port->serial->interface))
		return;

	/* wait one more character time, based on baud rate */
	/* (TIIsTxActive doesn't seem to wait for the last byte) */
	if ((baud_rate=port->baud_rate) == 0)
		baud_rate = 50;
	msleep(max(1,(10000+baud_rate-1)/baud_rate));
}

static int TIChooseConfiguration (struct usb_device *dev)
{
	// There may be multiple configurations on this device, in which case
	// we would need to read and parse all of them to find out which one
	// we want. However, we just support one config at this point,
	// configuration # 1, which is Config Descriptor 0.

	dbg ("%s - Number of Interfaces = %d", __FUNCTION__, dev->config->desc.bNumInterfaces);
	dbg ("%s - MAX Power            = %d", __FUNCTION__, dev->config->desc.bMaxPower*2);

	if (dev->config->desc.bNumInterfaces != 1) {
		dev_err (&dev->dev, "%s - bNumInterfaces is not 1, ERROR!\n", __FUNCTION__);
		return -ENODEV;
	}

	return 0;
}

static int TIReadRom (struct edgeport_serial *serial, int start_address, int length, __u8 *buffer)
{
	int status;

	if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) {
		status = TIReadDownloadMemory (serial->serial->dev,
					       start_address,
					       length,
					       serial->TI_I2C_Type,
					       buffer);
	} else {
		status = TIReadBootMemory (serial,
					   start_address,
					   length,
					   buffer);
	}

	return status;
}

static int TIWriteRom (struct edgeport_serial *serial, int start_address, int length, __u8 *buffer)
{
	if (serial->product_info.TiMode == TI_MODE_BOOT)
		return TIWriteBootMemory (serial,
					  start_address,
					  length,
					  buffer);

	if (serial->product_info.TiMode == TI_MODE_DOWNLOAD)
		return TIWriteDownloadI2C (serial,
					   start_address,
					   length,
					   serial->TI_I2C_Type,
					   buffer);

	return -EINVAL;
}


/* Read a descriptor header from I2C based on type */
static int TIGetDescriptorAddress (struct edgeport_serial *serial, int desc_type, struct ti_i2c_desc *rom_desc)
{
	int start_address;
	int status;

	/* Search for requested descriptor in I2C */
	start_address = 2;
	do {
		status = TIReadRom (serial,
				   start_address,
				   sizeof(struct ti_i2c_desc),
				   (__u8 *)rom_desc );
		if (status)
			return 0;

		if (rom_desc->Type == desc_type)
			return start_address;

		start_address = start_address + sizeof(struct ti_i2c_desc) +  rom_desc->Size;

	} while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type);
	
	return 0;
}

/* Validate descriptor checksum */
static int ValidChecksum(struct ti_i2c_desc *rom_desc, __u8 *buffer)
{
	__u16 i;
	__u8 cs = 0;

	for (i=0; i < rom_desc->Size; i++) {
		cs = (__u8)(cs + buffer[i]);
	}
	if (cs != rom_desc->CheckSum) {
		dbg ("%s - Mismatch %x - %x", __FUNCTION__, rom_desc->CheckSum, cs);
		return -EINVAL;
	}
	return 0;
}

/* Make sure that the I2C image is good */
static int TiValidateI2cImage (struct edgeport_serial *serial)
{
	struct device *dev = &serial->serial->dev->dev;
	int status = 0;
	struct ti_i2c_desc *rom_desc;
	int start_address = 2;
	__u8 *buffer;
	__u16 ttype;

	rom_desc = kmalloc (sizeof (*rom_desc), GFP_KERNEL);
	if (!rom_desc) {
		dev_err (dev, "%s - out of memory\n", __FUNCTION__);
		return -ENOMEM;
	}
	buffer = kmalloc (TI_MAX_I2C_SIZE, GFP_KERNEL);
	if (!buffer) {
		dev_err (dev, "%s - out of memory when allocating buffer\n", __FUNCTION__);
		kfree (rom_desc);
		return -ENOMEM;
	}

	// Read the first byte (Signature0) must be 0x52 or 0x10
	status = TIReadRom (serial, 0, 1, buffer);
	if (status)
		goto ExitTiValidateI2cImage; 

	if (*buffer != UMP5152 && *buffer != UMP3410) {
		dev_err (dev, "%s - invalid buffer signature\n", __FUNCTION__);
		status = -ENODEV;
		goto ExitTiValidateI2cImage;
	}

	do {
		// Validate the I2C
		status = TIReadRom (serial,
				start_address,
				sizeof(struct ti_i2c_desc),
				(__u8 *)rom_desc);
		if (status)
			break;

		if ((start_address + sizeof(struct ti_i2c_desc) + rom_desc->Size) > TI_MAX_I2C_SIZE) {
			status = -ENODEV;
			dbg ("%s - structure too big, erroring out.", __FUNCTION__);
			break;
		}

		dbg ("%s Type = 0x%x", __FUNCTION__, rom_desc->Type);

		// Skip type 2 record
		ttype = rom_desc->Type & 0x0f;
		if ( ttype != I2C_DESC_TYPE_FIRMWARE_BASIC
			&& ttype != I2C_DESC_TYPE_FIRMWARE_AUTO ) {
			// Read the descriptor data
			status = TIReadRom(serial,
						start_address+sizeof(struct ti_i2c_desc),
						rom_desc->Size,
						buffer);
			if (status)
				break;

			status = ValidChecksum(rom_desc, buffer);
			if (status)
				break;
		}
		start_address = start_address + sizeof(struct ti_i2c_desc) + rom_desc->Size;

	} while ((rom_desc->Type != I2C_DESC_TYPE_ION) && (start_address < TI_MAX_I2C_SIZE));

	if ((rom_desc->Type != I2C_DESC_TYPE_ION) || (start_address > TI_MAX_I2C_SIZE))
		status = -ENODEV;

ExitTiValidateI2cImage:	
	kfree (buffer);
	kfree (rom_desc);
	return status;
}

static int TIReadManufDescriptor (struct edgeport_serial *serial, __u8 *buffer)
{
	int status;
	int start_address;
	struct ti_i2c_desc *rom_desc;
	struct edge_ti_manuf_descriptor *desc;

	rom_desc = kmalloc (sizeof (*rom_desc), GFP_KERNEL);
	if (!rom_desc) {
		dev_err (&serial->serial->dev->dev, "%s - out of memory\n", __FUNCTION__);
		return -ENOMEM;
	}
	start_address = TIGetDescriptorAddress (serial, I2C_DESC_TYPE_ION, rom_desc);

	if (!start_address) {
		dbg ("%s - Edge Descriptor not found in I2C", __FUNCTION__);
		status = -ENODEV;
		goto exit;
	}

	// Read the descriptor data
	status = TIReadRom (serial,
				start_address+sizeof(struct ti_i2c_desc),
				rom_desc->Size,
				buffer);
	if (status)
		goto exit;
	
	status = ValidChecksum(rom_desc, buffer);
	
	desc = (struct edge_ti_manuf_descriptor *)buffer;
	dbg ( "%s - IonConfig      0x%x", __FUNCTION__, desc->IonConfig 	);
	dbg ( "%s - Version          %d", __FUNCTION__, desc->Version	  	);
	dbg ( "%s - Cpu/Board      0x%x", __FUNCTION__, desc->CpuRev_BoardRev	);
	dbg ( "%s - NumPorts         %d", __FUNCTION__, desc->NumPorts  	);	
	dbg ( "%s - NumVirtualPorts  %d", __FUNCTION__, desc->NumVirtualPorts	);	
	dbg ( "%s - TotalPorts       %d", __FUNCTION__, desc->TotalPorts  	);	

exit:
	kfree (rom_desc);
	return status;
}

/* Build firmware header used for firmware update */
static int BuildI2CFirmwareHeader (__u8 *header, struct device *dev)
{
	__u8 *buffer;
	int buffer_size;
	int i;
	__u8 cs = 0;
	struct ti_i2c_desc *i2c_header;
	struct ti_i2c_image_header *img_header;
	struct ti_i2c_firmware_rec *firmware_rec;

	// In order to update the I2C firmware we must change the type 2 record to type 0xF2.
	// This will force the UMP to come up in Boot Mode.  Then while in boot mode, the driver 
	// will download the latest firmware (padded to 15.5k) into the UMP ram. 
	// And finally when the device comes back up in download mode the driver will cause 
	// the new firmware to be copied from the UMP Ram to I2C and the firmware will update
	// the record type from 0xf2 to 0x02.
	
	// Allocate a 15.5k buffer + 2 bytes for version number (Firmware Record)
	buffer_size = (((1024 * 16) - 512 )+ sizeof(struct ti_i2c_firmware_rec));

	buffer = kmalloc (buffer_size, GFP_KERNEL);
	if (!buffer) {
		dev_err (dev, "%s - out of memory\n", __FUNCTION__);
		return -ENOMEM;
	}
	
	// Set entire image of 0xffs
	memset (buffer, 0xff, buffer_size);

	// Copy version number into firmware record
	firmware_rec = (struct ti_i2c_firmware_rec *)buffer;

	firmware_rec->Ver_Major	= OperationalCodeImageVersion.MajorVersion;
	firmware_rec->Ver_Minor	= OperationalCodeImageVersion.MinorVersion;

	// Pointer to fw_down memory image
	img_header = (struct ti_i2c_image_header *)&PagableOperationalCodeImage[0];

	memcpy (buffer + sizeof(struct ti_i2c_firmware_rec),
		&PagableOperationalCodeImage[sizeof(struct ti_i2c_image_header)],
		le16_to_cpu(img_header->Length));

	for (i=0; i < buffer_size; i++) {
		cs = (__u8)(cs + buffer[i]);
	}

	kfree (buffer);

	// Build new header
	i2c_header =  (struct ti_i2c_desc *)header;
	firmware_rec =  (struct ti_i2c_firmware_rec*)i2c_header->Data;
	
	i2c_header->Type	= I2C_DESC_TYPE_FIRMWARE_BLANK;
	i2c_header->Size	= (__u16)buffer_size;
	i2c_header->CheckSum	= cs;
	firmware_rec->Ver_Major	= OperationalCodeImageVersion.MajorVersion;
	firmware_rec->Ver_Minor	= OperationalCodeImageVersion.MinorVersion;

	return 0;
}

/* Try to figure out what type of I2c we have */
static int TIGetI2cTypeInBootMode (struct edgeport_serial *serial)
{
	int status;
	__u8 data;
		
	// Try to read type 2
	status = TIReadVendorRequestSync (serial->serial->dev,
					UMPC_MEMORY_READ,		// Request
					DTK_ADDR_SPACE_I2C_TYPE_II,	// wValue (Address type)
					0,		 		// wIndex
					&data,				// TransferBuffer
					0x01);				// TransferBufferLength
	if (status)
		dbg ("%s - read 2 status error = %d", __FUNCTION__, status);
	else
		dbg ("%s - read 2 data = 0x%x", __FUNCTION__, data);
	if ((!status) && (data == UMP5152 || data == UMP3410)) {
		dbg ("%s - ROM_TYPE_II", __FUNCTION__);
		serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
		return 0;
	}

	// Try to read type 3
	status = TIReadVendorRequestSync (serial->serial->dev,
					UMPC_MEMORY_READ,		// Request
					DTK_ADDR_SPACE_I2C_TYPE_III,	// wValue (Address type)
					0,				// wIndex
					&data,				// TransferBuffer
					0x01);				// TransferBufferLength
	if (status)
		dbg ("%s - read 3 status error = %d", __FUNCTION__, status);
	else
		dbg ("%s - read 2 data = 0x%x", __FUNCTION__, data);
	if ((!status) && (data == UMP5152 || data == UMP3410)) {
		dbg ("%s - ROM_TYPE_III", __FUNCTION__);
		serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_III;
		return 0;
	}

	dbg ("%s - Unknown", __FUNCTION__);
	serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
	return -ENODEV;
}

static int TISendBulkTransferSync (struct usb_serial *serial, void *buffer, int length, int *num_sent)
{
	int status;

	status = usb_bulk_msg (serial->dev,
				usb_sndbulkpipe(serial->dev,
						serial->port[0]->bulk_out_endpointAddress),
				buffer,
				length,
				num_sent,
				1000);
	return status;
}

/* Download given firmware image to the device (IN BOOT MODE) */
static int TIDownloadCodeImage (struct edgeport_serial *serial, __u8 *image, int image_length)
{
	int status = 0;
	int pos;
	int transfer;
	int done;

	// Transfer firmware image
	for (pos = 0; pos < image_length; ) {
		// Read the next buffer from file
		transfer = image_length - pos;
		if (transfer > EDGE_FW_BULK_MAX_PACKET_SIZE)
			transfer = EDGE_FW_BULK_MAX_PACKET_SIZE;

		// Transfer data
		status = TISendBulkTransferSync (serial->serial, &image[pos], transfer, &done);
		if (status)
			break;
		// Advance buffer pointer
		pos += done;
	}

	return status;
}

// FIXME!!!
static int TIConfigureBootDevice (struct usb_device *dev)
{
	return 0;
}

/**
 * DownloadTIFirmware - Download run-time operating firmware to the TI5052
 * 
 * This routine downloads the main operating code into the TI5052, using the
 * boot code already burned into E2PROM or ROM.
 */
static int TIDownloadFirmware (struct edgeport_serial *serial)
{
	struct device *dev = &serial->serial->dev->dev;
	int status = 0;
	int start_address;
	struct edge_ti_manuf_descriptor *ti_manuf_desc;
	struct usb_interface_descriptor *interface;
	int download_cur_ver;
	int download_new_ver;

	/* This routine is entered by both the BOOT mode and the Download mode
	 * We can determine which code is running by the reading the config
	 * descriptor and if we have only one bulk pipe it is in boot mode
	 */
	serial->product_info.hardware_type = HARDWARE_TYPE_TIUMP;

	/* Default to type 2 i2c */
	serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;

	status = TIChooseConfiguration (serial->serial->dev);
	if (status)
		return status;

	interface = &serial->serial->interface->cur_altsetting->desc;
	if (!interface) {
		dev_err (dev, "%s - no interface set, error!\n", __FUNCTION__);
		return -ENODEV;
	}

	// Setup initial mode -- the default mode 0 is TI_MODE_CONFIGURING
	// if we have more than one endpoint we are definitely in download mode
	if (interface->bNumEndpoints > 1)
		serial->product_info.TiMode = TI_MODE_DOWNLOAD;
	else
		// Otherwise we will remain in configuring mode
		serial->product_info.TiMode = TI_MODE_CONFIGURING;

	// Save Download Version Number
	OperationalCodeImageVersion.MajorVersion = PagableOperationalCodeImageVersion.MajorVersion;
	OperationalCodeImageVersion.MinorVersion = PagableOperationalCodeImageVersion.MinorVersion;
	OperationalCodeImageVersion.BuildNumber	 = PagableOperationalCodeImageVersion.BuildNumber;

	/********************************************************************/
	/* Download Mode */
	/********************************************************************/
	if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) {
		struct ti_i2c_desc *rom_desc;

		dbg ("%s - <<<<<<<<<<<<<<<RUNNING IN DOWNLOAD MODE>>>>>>>>>>", __FUNCTION__);

		status = TiValidateI2cImage (serial);
		if (status) {
			dbg ("%s - <<<<<<<<<<<<<<<DOWNLOAD MODE -- BAD I2C >>>>>>>>>>",
			     __FUNCTION__);
			return status;
		}
		
		/* Validate Hardware version number
		 * Read Manufacturing Descriptor from TI Based Edgeport
		 */
		ti_manuf_desc = kmalloc (sizeof (*ti_manuf_desc), GFP_KERNEL);
		if (!ti_manuf_desc) {
			dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
			return -ENOMEM;
		}
		status = TIReadManufDescriptor (serial, (__u8 *)ti_manuf_desc);
		if (status) {
			kfree (ti_manuf_desc);
			return status;
		}

		// Check version number of ION descriptor
		if (!ignore_cpu_rev && TI_GET_CPU_REVISION(ti_manuf_desc->CpuRev_BoardRev) < 2) {
			dbg ( "%s - Wrong CPU Rev %d (Must be 2)", __FUNCTION__, 
			     TI_GET_CPU_REVISION(ti_manuf_desc->CpuRev_BoardRev));
			kfree (ti_manuf_desc);
		   	return -EINVAL;
		}

		rom_desc = kmalloc (sizeof (*rom_desc), GFP_KERNEL);
		if (!rom_desc) {
			dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
			kfree (ti_manuf_desc);
			return -ENOMEM;
		}

		// Search for type 2 record (firmware record)
		if ((start_address = TIGetDescriptorAddress (serial, I2C_DESC_TYPE_FIRMWARE_BASIC, rom_desc)) != 0) {
			struct ti_i2c_firmware_rec *firmware_version;
			__u8 record;

			dbg ("%s - Found Type FIRMWARE (Type 2) record", __FUNCTION__);

			firmware_version = kmalloc (sizeof (*firmware_version), GFP_KERNEL);
			if (!firmware_version) {
				dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return -ENOMEM;
			}

			// Validate version number				
			// Read the descriptor data
			status = TIReadRom (serial,
					start_address+sizeof(struct ti_i2c_desc),
					sizeof(struct ti_i2c_firmware_rec),
					(__u8 *)firmware_version);
			if (status) {
				kfree (firmware_version);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}

			// Check version number of download with current version in I2c
			download_cur_ver = (firmware_version->Ver_Major << 8) + 
					   (firmware_version->Ver_Minor);
			download_new_ver = (OperationalCodeImageVersion.MajorVersion << 8) +
					   (OperationalCodeImageVersion.MinorVersion);

			dbg ("%s - >>>Firmware Versions Device %d.%d  Driver %d.%d",
			     __FUNCTION__,
			     firmware_version->Ver_Major,
			     firmware_version->Ver_Minor,
			     OperationalCodeImageVersion.MajorVersion,
			     OperationalCodeImageVersion.MinorVersion);

			// Check if we have an old version in the I2C and update if necessary
			if (download_cur_ver != download_new_ver) {
				dbg ("%s - Update I2C Download from %d.%d to %d.%d",
				     __FUNCTION__,
				     firmware_version->Ver_Major,
				     firmware_version->Ver_Minor,
				     OperationalCodeImageVersion.MajorVersion,
				     OperationalCodeImageVersion.MinorVersion);

				// In order to update the I2C firmware we must change the type 2 record to type 0xF2.
				// This will force the UMP to come up in Boot Mode.  Then while in boot mode, the driver 
				// will download the latest firmware (padded to 15.5k) into the UMP ram. 
				// And finally when the device comes back up in download mode the driver will cause 
				// the new firmware to be copied from the UMP Ram to I2C and the firmware will update
				// the record type from 0xf2 to 0x02.

				record = I2C_DESC_TYPE_FIRMWARE_BLANK;

				// Change the I2C Firmware record type to 0xf2 to trigger an update
				status = TIWriteRom (serial,
							start_address,
							sizeof(record),
							&record);
				if (status) {
					kfree (firmware_version);
					kfree (rom_desc);
					kfree (ti_manuf_desc);
					return status;
				}

				// verify the write -- must do this in order for write to 
				// complete before we do the hardware reset
				status = TIReadRom (serial,
							start_address,
							sizeof(record),
							&record);

				if (status) {
					kfree (firmware_version);
					kfree (rom_desc);
					kfree (ti_manuf_desc);
					return status;
				}

				if (record != I2C_DESC_TYPE_FIRMWARE_BLANK) {
					dev_err (dev, "%s - error resetting device\n", __FUNCTION__);
					kfree (firmware_version);
					kfree (rom_desc);
					kfree (ti_manuf_desc);
					return -ENODEV;
				}

				dbg ("%s - HARDWARE RESET", __FUNCTION__);

				// Reset UMP -- Back to BOOT MODE
				status = TISendVendorRequestSync (serial->serial->dev,
								UMPC_HARDWARE_RESET,	// Request
								0,			// wValue
								0,			// wIndex
								NULL,			// TransferBuffer
								0);			// TransferBufferLength

				dbg ( "%s - HARDWARE RESET return %d", __FUNCTION__, status);

				/* return an error on purpose. */
				kfree (firmware_version);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return -ENODEV;
			}
			kfree (firmware_version);
		}
		// Search for type 0xF2 record (firmware blank record)
		else if ((start_address = TIGetDescriptorAddress (serial, I2C_DESC_TYPE_FIRMWARE_BLANK, rom_desc)) != 0) {
			#define HEADER_SIZE	(sizeof(struct ti_i2c_desc) + sizeof(struct ti_i2c_firmware_rec))
			__u8 *header;
			__u8 *vheader;

			header  = kmalloc (HEADER_SIZE, GFP_KERNEL);
			if (!header) {
				dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return -ENOMEM;
			}
				
			vheader = kmalloc (HEADER_SIZE, GFP_KERNEL);
			if (!vheader) {
				dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
				kfree (header);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return -ENOMEM;
			}
			
			dbg ("%s - Found Type BLANK FIRMWARE (Type F2) record", __FUNCTION__);

			// In order to update the I2C firmware we must change the type 2 record to type 0xF2.
			// This will force the UMP to come up in Boot Mode.  Then while in boot mode, the driver 
			// will download the latest firmware (padded to 15.5k) into the UMP ram. 
			// And finally when the device comes back up in download mode the driver will cause 
			// the new firmware to be copied from the UMP Ram to I2C and the firmware will update
			// the record type from 0xf2 to 0x02.
			status = BuildI2CFirmwareHeader(header, dev);
			if (status) {
				kfree (vheader);
				kfree (header);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}

			// Update I2C with type 0xf2 record with correct size and checksum
			status = TIWriteRom (serial,
						start_address,
						HEADER_SIZE,
						header);
			if (status) {
				kfree (vheader);
				kfree (header);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}

			// verify the write -- must do this in order for write to 
			// complete before we do the hardware reset
			status = TIReadRom (serial,
						start_address,
						HEADER_SIZE,
						vheader);

			if (status) {
				dbg ("%s - can't read header back", __FUNCTION__);
				kfree (vheader);
				kfree (header);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}
			if (memcmp(vheader, header, HEADER_SIZE)) {
				dbg ("%s - write download record failed", __FUNCTION__);
				kfree (vheader);
				kfree (header);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}

			kfree (vheader);
			kfree (header);

			dbg ("%s - Start firmware update", __FUNCTION__);

			// Tell firmware to copy download image into I2C 
			status = TISendVendorRequestSync (serial->serial->dev,
						UMPC_COPY_DNLD_TO_I2C,	// Request
						0,			// wValue 
						0,			// wIndex
						NULL,			// TransferBuffer
						0);			// TransferBufferLength

		  	dbg ("%s - Update complete 0x%x", __FUNCTION__, status);
			if (status) {
				dev_err (dev, "%s - UMPC_COPY_DNLD_TO_I2C failed\n", __FUNCTION__);
				kfree (rom_desc);
				kfree (ti_manuf_desc);
				return status;
			}
		}

		// The device is running the download code
		kfree (rom_desc);
		kfree (ti_manuf_desc);
		return 0;
	}

	/********************************************************************/
	/* Boot Mode */
	/********************************************************************/
	dbg ("%s - <<<<<<<<<<<<<<<RUNNING IN BOOT MODE>>>>>>>>>>>>>>>",
	     __FUNCTION__);

	// Configure the TI device so we can use the BULK pipes for download
	status = TIConfigureBootDevice (serial->serial->dev);
	if (status)
		return status;

	if (le16_to_cpu(serial->serial->dev->descriptor.idVendor) != USB_VENDOR_ID_ION) {
		dbg ("%s - VID = 0x%x", __FUNCTION__,
		     le16_to_cpu(serial->serial->dev->descriptor.idVendor));
		serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II;
		goto StayInBootMode;
	}

	// We have an ION device (I2c Must be programmed)
	// Determine I2C image type
	if (TIGetI2cTypeInBootMode(serial)) {
		goto StayInBootMode;
	}

	// Registry variable set?
	if (TIStayInBootMode) {
		dbg ("%s - TIStayInBootMode", __FUNCTION__);
		goto StayInBootMode;
	}

	// Check for ION Vendor ID and that the I2C is valid
	if (!TiValidateI2cImage(serial)) {
		struct ti_i2c_image_header *header;
		int i;
		__u8 cs = 0;
		__u8 *buffer;
		int buffer_size;

		/* Validate Hardware version number
		 * Read Manufacturing Descriptor from TI Based Edgeport
		 */
		ti_manuf_desc = kmalloc (sizeof (*ti_manuf_desc), GFP_KERNEL);
		if (!ti_manuf_desc) {
			dev_err (dev, "%s - out of memory.\n", __FUNCTION__);
			return -ENOMEM;
		}
		status = TIReadManufDescriptor (serial, (__u8 *)ti_manuf_desc);
		if (status) {
			kfree (ti_manuf_desc);
			goto StayInBootMode;
		}

		// Check for version 2
		if (!ignore_cpu_rev && TI_GET_CPU_REVISION(ti_manuf_desc->CpuRev_BoardRev) < 2) {
			dbg ("%s - Wrong CPU Rev %d (Must be 2)", __FUNCTION__,
			     TI_GET_CPU_REVISION(ti_manuf_desc->CpuRev_BoardRev));
			kfree (ti_manuf_desc);
			goto StayInBootMode;
		}

		kfree (ti_manuf_desc);

		// In order to update the I2C firmware we must change the type 2 record to type 0xF2.
		// This will force the UMP to come up in Boot Mode.  Then while in boot mode, the driver 
		// will download the latest firmware (padded to 15.5k) into the UMP ram. 
		// And finally when the device comes back up in download mode the driver will cause 
		// the new firmware to be copied from the UMP Ram to I2C and the firmware will update
		// the record type from 0xf2 to 0x02.
		
		/*
		 * Do we really have to copy the whole firmware image,
		 * or could we do this in place!
		 */

		// Allocate a 15.5k buffer + 3 byte header
		buffer_size = (((1024 * 16) - 512) + sizeof(struct ti_i2c_image_header));
		buffer = kmalloc (buffer_size, GFP_KERNEL);
		if (!buffer) {
			dev_err (dev, "%s - out of memory\n", __FUNCTION__);
			return -ENOMEM;
		}
		
		// Initialize the buffer to 0xff (pad the buffer)
		memset (buffer, 0xff, buffer_size);

		memcpy (buffer, &PagableOperationalCodeImage[0], PagableOperationalCodeSize);

		for(i = sizeof(struct ti_i2c_image_header); i < buffer_size; i++) {
			cs = (__u8)(cs + buffer[i]);
		}
		
		header = (struct ti_i2c_image_header *)buffer;
		
		// update length and checksum after padding
		header->Length 	 = cpu_to_le16((__u16)(buffer_size - sizeof(struct ti_i2c_image_header)));
		header->CheckSum = cs;

		// Download the operational code 
		dbg ("%s - Downloading operational code image (TI UMP)", __FUNCTION__);
		status = TIDownloadCodeImage (serial, buffer, buffer_size);

		kfree (buffer);

		if (status) {
	  		dbg ("%s - Error downloading operational code image", __FUNCTION__);
			return status;
		}

		// Device will reboot
		serial->product_info.TiMode = TI_MODE_TRANSITIONING;

  		dbg ("%s - Download successful -- Device rebooting...", __FUNCTION__);

		/* return an error on purpose */
		return -ENODEV;
	}

StayInBootMode:
	// Eprom is invalid or blank stay in boot mode
	dbg ("%s - <<<<<<<<<<<<<<<STAYING IN BOOT MODE>>>>>>>>>>>>", __FUNCTION__);
	serial->product_info.TiMode = TI_MODE_BOOT;

	return 0;
}


static int TISetDtr (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);
	port->shadow_mcr |= MCR_DTR;

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_DTR,
				(__u8)(UMPM_UART1_PORT + port_number),
				1,	/* set */
				NULL,
				0);
}

static int TIClearDtr (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);
	port->shadow_mcr &= ~MCR_DTR;

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_DTR,
				(__u8)(UMPM_UART1_PORT + port_number),
				0,	/* clear */
				NULL,
				0);
}

static int TISetRts (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);
	port->shadow_mcr |= MCR_RTS;

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_RTS,
				(__u8)(UMPM_UART1_PORT + port_number),
				1,	/* set */
				NULL,
				0);
}

static int TIClearRts (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);
	port->shadow_mcr &= ~MCR_RTS;

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_RTS,
				(__u8)(UMPM_UART1_PORT + port_number),
				0,	/* clear */
				NULL,
				0);
}

static int TISetLoopBack (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_LOOPBACK,
				(__u8)(UMPM_UART1_PORT + port_number),
				1,	/* set */
				NULL,
				0);
}

static int TIClearLoopBack (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_LOOPBACK,
				(__u8)(UMPM_UART1_PORT + port_number),
				0,	/* clear */
				NULL,
				0);
}

static int TISetBreak (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_BREAK,
				(__u8)(UMPM_UART1_PORT + port_number),
				1,	/* set */
				NULL,
				0);
}

static int TIClearBreak (struct edgeport_port *port)
{
	int port_number = port->port->number - port->port->serial->minor;

	dbg ("%s", __FUNCTION__);

	return TIWriteCommandSync (port->port->serial->dev,
				UMPC_SET_CLR_BREAK,
				(__u8)(UMPM_UART1_PORT + port_number),
				0,	/* clear */
				NULL,
				0);
}

static int TIRestoreMCR (struct edgeport_port *port, __u8 mcr)
{
	int status = 0;

	dbg ("%s - %x", __FUNCTION__, mcr);

	if (mcr & MCR_DTR)
		status = TISetDtr (port);
	else
		status = TIClearDtr (port);

	if (status)
		return status;

	if (mcr & MCR_RTS)
		status = TISetRts (port);
	else
		status = TIClearRts (port);

	if (status)
		return status;

	if (mcr & MCR_LOOPBACK)
		status = TISetLoopBack (port);
	else
		status = TIClearLoopBack (port);

	return status;
}


/* Convert TI LSR to standard UART flags */
static __u8 MapLineStatus (__u8 ti_lsr)
{
	__u8 lsr = 0;

#define MAP_FLAG(flagUmp, flagUart)    \
	if (ti_lsr & flagUmp) \
		lsr |= flagUart;

	MAP_FLAG(UMP_UART_LSR_OV_MASK, LSR_OVER_ERR)	/* overrun */
	MAP_FLAG(UMP_UART_LSR_PE_MASK, LSR_PAR_ERR)	/* parity error */
	MAP_FLAG(UMP_UART_LSR_FE_MASK, LSR_FRM_ERR)	/* framing error */
	MAP_FLAG(UMP_UART_LSR_BR_MASK, LSR_BREAK)	/* break detected */
	MAP_FLAG(UMP_UART_LSR_RX_MASK, LSR_RX_AVAIL)	/* receive data available */
	MAP_FLAG(UMP_UART_LSR_TX_MASK, LSR_TX_EMPTY)	/* transmit holding register empty */

#undef MAP_FLAG

	return lsr;
}

static void handle_new_msr (struct edgeport_port *edge_port, __u8 msr)
{
	struct async_icount *icount;
	struct tty_struct *tty;

	dbg ("%s - %02x", __FUNCTION__, msr);

	if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR | EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) {
		icount = &edge_port->icount;

		/* update input line counters */
		if (msr & EDGEPORT_MSR_DELTA_CTS)
			icount->cts++;
		if (msr & EDGEPORT_MSR_DELTA_DSR)
			icount->dsr++;
		if (msr & EDGEPORT_MSR_DELTA_CD)
			icount->dcd++;
		if (msr & EDGEPORT_MSR_DELTA_RI)
			icount->rng++;
		wake_up_interruptible (&edge_port->delta_msr_wait);
	}

	/* Save the new modem status */
	edge_port->shadow_msr = msr & 0xf0;

	tty = edge_port->port->tty;
	/* handle CTS flow control */
	if (tty && C_CRTSCTS(tty)) {
		if (msr & EDGEPORT_MSR_CTS) {
			tty->hw_stopped = 0;
			tty_wakeup(tty);
		} else {
			tty->hw_stopped = 1;
		}
	}

	return;
}

static void handle_new_lsr (struct edgeport_port *edge_port, int lsr_data, __u8 lsr, __u8 data)
{
	struct async_icount *icount;
	__u8 new_lsr = (__u8)(lsr & (__u8)(LSR_OVER_ERR | LSR_PAR_ERR | LSR_FRM_ERR | LSR_BREAK));

	dbg ("%s - %02x", __FUNCTION__, new_lsr);

	edge_port->shadow_lsr = lsr;

	if (new_lsr & LSR_BREAK) {
		/*
		 * Parity and Framing errors only count if they
		 * occur exclusive of a break being received.
		 */
		new_lsr &= (__u8)(LSR_OVER_ERR | LSR_BREAK);
	}

	/* Place LSR data byte into Rx buffer */
	if (lsr_data && edge_port->port->tty)
		edge_tty_recv(&edge_port->port->dev, edge_port->port->tty, &data, 1);

	/* update input line counters */
	icount = &edge_port->icount;
	if (new_lsr & LSR_BREAK)
		icount->brk++;
	if (new_lsr & LSR_OVER_ERR)
		icount->overrun++;
	if (new_lsr & LSR_PAR_ERR)
		icount->parity++;
	if (new_lsr & LSR_FRM_ERR)
		icount->frame++;
}


static void edge_interrupt_callback (struct urb *urb, struct pt_regs *regs)
{
	struct edgeport_serial *edge_serial = (struct edgeport_serial *)urb->context;
	struct usb_serial_port *port;
	struct edgeport_port *edge_port;
	unsigned char *data = urb->transfer_buffer;
	int length = urb->actual_length;
	int port_number;
	int function;
	int status;
	__u8 lsr;
	__u8 msr;

	dbg("%s", __FUNCTION__);

	switch (urb->status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status);
		return;
	default:
		dev_err(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __FUNCTION__, urb->status);
		goto exit;
	}

	if (!length) {
		dbg ("%s - no data in urb", __FUNCTION__);
		goto exit;
	}
		
	usb_serial_debug_data(debug, &edge_serial->serial->dev->dev, __FUNCTION__, length, data);
		
	if (length != 2) {
		dbg ("%s - expecting packet of size 2, got %d", __FUNCTION__, length);
		goto exit;
	}

	port_number = TIUMP_GET_PORT_FROM_CODE (data[0]);
	function    = TIUMP_GET_FUNC_FROM_CODE (data[0]);
	dbg ("%s - port_number %d, function %d, info 0x%x",
	     __FUNCTION__, port_number, function, data[1]);
	port = edge_serial->serial->port[port_number];
	edge_port = usb_get_serial_port_data(port);
	if (!edge_port) {
		dbg ("%s - edge_port not found", __FUNCTION__);
		return;
	}
	switch (function) {
	case TIUMP_INTERRUPT_CODE_LSR:
		lsr = MapLineStatus(data[1]);
		if (lsr & UMP_UART_LSR_DATA_MASK) {
			/* Save the LSR event for bulk read completion routine */
			dbg ("%s - LSR Event Port %u LSR Status = %02x",
			     __FUNCTION__, port_number, lsr);
			edge_port->lsr_event = 1;
			edge_port->lsr_mask = lsr;
		} else {
			dbg ("%s - ===== Port %d LSR Status = %02x ======",
			     __FUNCTION__, port_number, lsr);
			handle_new_lsr (edge_port, 0, lsr, 0);
		}
		break;

	case TIUMP_INTERRUPT_CODE_MSR:	// MSR
		/* Copy MSR from UMP */
		msr = data[1];
		dbg ("%s - ===== Port %u MSR Status = %02x ======\n",
		     __FUNCTION__, port_number, msr);
		handle_new_msr (edge_port, msr);
		break;

	default:
		dev_err (&urb->dev->dev, "%s - Unknown Interrupt code from UMP %x\n",
			 __FUNCTION__, data[1]);
		break;
		
	}

exit:
	status = usb_submit_urb (urb, GFP_ATOMIC);
	if (status)
		dev_err (&urb->dev->dev, "%s - usb_submit_urb failed with result %d\n",
			 __FUNCTION__, status);
}

static void edge_bulk_in_callback (struct urb *urb, struct pt_regs *regs)
{
	struct edgeport_port *edge_port = (struct edgeport_port *)urb->context;
	unsigned char *data = urb->transfer_buffer;
	struct tty_struct *tty;
	int status = 0;
	int port_number;

	dbg("%s", __FUNCTION__);

	switch (urb->status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status);
		return;
	default:
		dev_err (&urb->dev->dev,"%s - nonzero read bulk status received: %d\n",
		     __FUNCTION__, urb->status );
	}

	if (urb->status == -EPIPE)
		goto exit;

	if (urb->status) {
		dev_err(&urb->dev->dev,"%s - stopping read!\n", __FUNCTION__);
		return;
	}

	port_number = edge_port->port->number - edge_port->port->serial->minor;

	if (edge_port->lsr_event) {
		edge_port->lsr_event = 0;
		dbg ("%s ===== Port %u LSR Status = %02x, Data = %02x ======",
		     __FUNCTION__, port_number, edge_port->lsr_mask, *data);
		handle_new_lsr (edge_port, 1, edge_port->lsr_mask, *data);
		/* Adjust buffer length/pointer */
		--urb->actual_length;
		++data;
	}

	tty = edge_port->port->tty;
	if (tty && urb->actual_length) {
		usb_serial_debug_data(debug, &edge_port->port->dev, __FUNCTION__, urb->actual_length, data);

		if (edge_port->close_pending) {
			dbg ("%s - close is pending, dropping data on the floor.", __FUNCTION__);
		} else {
			edge_tty_recv(&edge_port->port->dev, tty, data, urb->actual_length);
		}
		edge_port->icount.rx += urb->actual_length;
	}

exit:
	/* continue read unless stopped */
	spin_lock(&edge_port->ep_lock);
	if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING) {
		urb->dev = edge_port->port->serial->dev;
		status = usb_submit_urb(urb, GFP_ATOMIC);
	} else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING) {
		edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED;
	}
	spin_unlock(&edge_port->ep_lock);
	if (status)
		dev_err (&urb->dev->dev, "%s - usb_submit_urb failed with result %d\n",
			 __FUNCTION__, status);
}

static void edge_tty_recv(struct device *dev, struct tty_struct *tty, unsigned char *data, int length)
{
	int cnt;

	do {
		cnt = tty_buffer_request_room(tty, length);
		if (cnt < length) {
			dev_err(dev, "%s - dropping data, %d bytes lost\n",
				__FUNCTION__, length - cnt);
			if(cnt == 0)
				break;
		}
		tty_insert_flip_string(tty, data, cnt);
		data += cnt;
		length -= cnt;
	} while (length > 0);

	tty_flip_buffer_push(tty);
}

static void edge_bulk_out_callback (struct urb *urb, struct pt_regs *regs)
{
	struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);

	dbg ("%s - port %d", __FUNCTION__, port->number);

	edge_port->ep_write_urb_in_use = 0;

	switch (urb->status) {
	case 0:
		/* success */
		break;
	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* this urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d", __FUNCTION__, urb->status);
		return;
	default:
		dev_err (&urb->dev->dev,"%s - nonzero write bulk status received: %d\n",
		     __FUNCTION__, urb->status);
	}

	/* send any buffered data */
	edge_send(port);
}

static int edge_open (struct usb_serial_port *port, struct file * filp)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct edgeport_serial *edge_serial;
	struct usb_device *dev;
	struct urb *urb;
	int port_number;
	int status;
	u16 open_settings;
	u8 transaction_timeout;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return -ENODEV;

	if (port->tty)
		port->tty->low_latency = low_latency;

	port_number = port->number - port->serial->minor;
	switch (port_number) {
		case 0:
			edge_port->uart_base = UMPMEM_BASE_UART1;
			edge_port->dma_address = UMPD_OEDB1_ADDRESS;
			break;
		case 1:
			edge_port->uart_base = UMPMEM_BASE_UART2;
			edge_port->dma_address = UMPD_OEDB2_ADDRESS;
			break;
		default:
			dev_err (&port->dev, "Unknown port number!!!\n");
			return -ENODEV;
	}

	dbg ("%s - port_number = %d, uart_base = %04x, dma_address = %04x",
	     __FUNCTION__, port_number, edge_port->uart_base, edge_port->dma_address);

	dev = port->serial->dev;

	memset (&(edge_port->icount), 0x00, sizeof(edge_port->icount));
	init_waitqueue_head (&edge_port->delta_msr_wait);

	/* turn off loopback */
	status = TIClearLoopBack (edge_port);
	if (status) {
		dev_err(&port->dev,"%s - cannot send clear loopback command, %d\n",
			__FUNCTION__, status);
		return status;
	}
	
	/* set up the port settings */
	edge_set_termios (port, NULL);

	/* open up the port */

	/* milliseconds to timeout for DMA transfer */
	transaction_timeout = 2;

	edge_port->ump_read_timeout = max (20, ((transaction_timeout * 3) / 2) );

	// milliseconds to timeout for DMA transfer
	open_settings = (u8)(UMP_DMA_MODE_CONTINOUS | 
			     UMP_PIPE_TRANS_TIMEOUT_ENA | 
			     (transaction_timeout << 2));

	dbg ("%s - Sending UMPC_OPEN_PORT", __FUNCTION__);

	/* Tell TI to open and start the port */
	status = TIWriteCommandSync (dev,
					UMPC_OPEN_PORT,
					(u8)(UMPM_UART1_PORT + port_number),
					open_settings,
					NULL,
					0);
	if (status) {
		dev_err(&port->dev,"%s - cannot send open command, %d\n", __FUNCTION__, status);
		return status;
	}

	/* Start the DMA? */
	status = TIWriteCommandSync (dev,
					UMPC_START_PORT,
					(u8)(UMPM_UART1_PORT + port_number),
					0,
					NULL,
					0);
	if (status) {
		dev_err(&port->dev,"%s - cannot send start DMA command, %d\n", __FUNCTION__, status);
		return status;
	}

	/* Clear TX and RX buffers in UMP */
	status = TIPurgeDataSync (port, UMP_PORT_DIR_OUT | UMP_PORT_DIR_IN);
	if (status) {
		dev_err(&port->dev,"%s - cannot send clear buffers command, %d\n", __FUNCTION__, status);
		return status;
	}

	/* Read Initial MSR */
	status = TIReadVendorRequestSync (dev,
					UMPC_READ_MSR,	// Request
					0,		// wValue
					(__u16)(UMPM_UART1_PORT + port_number),	// wIndex (Address)
					&edge_port->shadow_msr,			// TransferBuffer
					1);					// TransferBufferLength
	if (status) {
 		dev_err(&port->dev,"%s - cannot send read MSR command, %d\n", __FUNCTION__, status);
		return status;
	}

	dbg ("ShadowMSR 0x%X", edge_port->shadow_msr);
 
	/* Set Initial MCR */
	edge_port->shadow_mcr = MCR_RTS | MCR_DTR;
	dbg ("ShadowMCR 0x%X", edge_port->shadow_mcr);

	edge_serial = edge_port->edge_serial;
	if (down_interruptible(&edge_serial->es_sem))
		return -ERESTARTSYS;
	if (edge_serial->num_ports_open == 0) {
		/* we are the first port to be opened, let's post the interrupt urb */
		urb = edge_serial->serial->port[0]->interrupt_in_urb;
		if (!urb) {
			dev_err (&port->dev, "%s - no interrupt urb present, exiting\n", __FUNCTION__);
			status = -EINVAL;
			goto up_es_sem;
		}
		urb->complete = edge_interrupt_callback;
		urb->context = edge_serial;
		urb->dev = dev;
		status = usb_submit_urb (urb, GFP_KERNEL);
		if (status) {
			dev_err (&port->dev, "%s - usb_submit_urb failed with value %d\n", __FUNCTION__, status);
			goto up_es_sem;
		}
	}

	/*
	 * reset the data toggle on the bulk endpoints to work around bug in
	 * host controllers where things get out of sync some times
	 */
	usb_clear_halt (dev, port->write_urb->pipe);
	usb_clear_halt (dev, port->read_urb->pipe);

	/* start up our bulk read urb */
	urb = port->read_urb;
	if (!urb) {
		dev_err (&port->dev, "%s - no read urb present, exiting\n", __FUNCTION__);
		status = -EINVAL;
		goto unlink_int_urb;
	}
	edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
	urb->complete = edge_bulk_in_callback;
	urb->context = edge_port;
	urb->dev = dev;
	status = usb_submit_urb (urb, GFP_KERNEL);
	if (status) {
		dev_err (&port->dev, "%s - read bulk usb_submit_urb failed with value %d\n", __FUNCTION__, status);
		goto unlink_int_urb;
	}

	++edge_serial->num_ports_open;

	dbg("%s - exited", __FUNCTION__);

	goto up_es_sem;

unlink_int_urb:
	if (edge_port->edge_serial->num_ports_open == 0)
		usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
up_es_sem:
	up(&edge_serial->es_sem);
	return status;
}

static void edge_close (struct usb_serial_port *port, struct file *filp)
{
	struct edgeport_serial *edge_serial;
	struct edgeport_port *edge_port;
	int port_number;
	int status;

	dbg("%s - port %d", __FUNCTION__, port->number);
			 
	edge_serial = usb_get_serial_data(port->serial);
	edge_port = usb_get_serial_port_data(port);
	if ((edge_serial == NULL) || (edge_port == NULL))
		return;
	
	/* The bulkreadcompletion routine will check 
	 * this flag and dump add read data */
	edge_port->close_pending = 1;

	/* chase the port close and flush */
	TIChasePort (edge_port, (HZ*closing_wait)/100, 1);

	usb_kill_urb(port->read_urb);
	usb_kill_urb(port->write_urb);
	edge_port->ep_write_urb_in_use = 0;

	/* assuming we can still talk to the device,
	 * send a close port command to it */
	dbg("%s - send umpc_close_port", __FUNCTION__);
	port_number = port->number - port->serial->minor;
	status = TIWriteCommandSync (port->serial->dev,
				     UMPC_CLOSE_PORT,
				     (__u8)(UMPM_UART1_PORT + port_number),
				     0,
				     NULL,
				     0);
	down(&edge_serial->es_sem);
	--edge_port->edge_serial->num_ports_open;
	if (edge_port->edge_serial->num_ports_open <= 0) {
		/* last port is now closed, let's shut down our interrupt urb */
		usb_kill_urb(port->serial->port[0]->interrupt_in_urb);
		edge_port->edge_serial->num_ports_open = 0;
	}
	up(&edge_serial->es_sem);
	edge_port->close_pending = 0;

	dbg("%s - exited", __FUNCTION__);
}

static int edge_write (struct usb_serial_port *port, const unsigned char *data, int count)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	unsigned long flags;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (count == 0) {
		dbg("%s - write request of 0 bytes", __FUNCTION__);
		return 0;
	}

	if (edge_port == NULL)
		return -ENODEV;
	if (edge_port->close_pending == 1)
		return -ENODEV;

	spin_lock_irqsave(&edge_port->ep_lock, flags);
	count = edge_buf_put(edge_port->ep_out_buf, data, count);
	spin_unlock_irqrestore(&edge_port->ep_lock, flags);

	edge_send(port);

	return count;
}

static void edge_send(struct usb_serial_port *port)
{
	int count, result;
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct tty_struct *tty = port->tty;
	unsigned long flags;


	dbg("%s - port %d", __FUNCTION__, port->number);

	spin_lock_irqsave(&edge_port->ep_lock, flags);

	if (edge_port->ep_write_urb_in_use) {
		spin_unlock_irqrestore(&edge_port->ep_lock, flags);
		return;
	}

	count = edge_buf_get(edge_port->ep_out_buf,
				port->write_urb->transfer_buffer,
				port->bulk_out_size);

	if (count == 0) {
		spin_unlock_irqrestore(&edge_port->ep_lock, flags);
		return;
	}

	edge_port->ep_write_urb_in_use = 1;

	spin_unlock_irqrestore(&edge_port->ep_lock, flags);

	usb_serial_debug_data(debug, &port->dev, __FUNCTION__, count, port->write_urb->transfer_buffer);

	/* set up our urb */
	usb_fill_bulk_urb (port->write_urb, port->serial->dev,
			   usb_sndbulkpipe (port->serial->dev,
					    port->bulk_out_endpointAddress),
			   port->write_urb->transfer_buffer, count,
			   edge_bulk_out_callback,
			   port);

	/* send the data out the bulk port */
	result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
	if (result) {
		dev_err(&port->dev, "%s - failed submitting write urb, error %d\n", __FUNCTION__, result);
		edge_port->ep_write_urb_in_use = 0;
		// TODO: reschedule edge_send
	} else {
		edge_port->icount.tx += count;
	}

	/* wakeup any process waiting for writes to complete */
	/* there is now more room in the buffer for new writes */
	if (tty) {
		/* let the tty driver wakeup if it has a special write_wakeup function */
		tty_wakeup(tty);
	}
}

static int edge_write_room (struct usb_serial_port *port)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	int room = 0;
	unsigned long flags;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return -ENODEV;
	if (edge_port->close_pending == 1)
		return -ENODEV;

	spin_lock_irqsave(&edge_port->ep_lock, flags);
	room = edge_buf_space_avail(edge_port->ep_out_buf);
	spin_unlock_irqrestore(&edge_port->ep_lock, flags);

	dbg("%s - returns %d", __FUNCTION__, room);
	return room;
}

static int edge_chars_in_buffer (struct usb_serial_port *port)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	int chars = 0;
	unsigned long flags;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return -ENODEV;
	if (edge_port->close_pending == 1)
		return -ENODEV;

	spin_lock_irqsave(&edge_port->ep_lock, flags);
	chars = edge_buf_data_avail(edge_port->ep_out_buf);
	spin_unlock_irqrestore(&edge_port->ep_lock, flags);

	dbg ("%s - returns %d", __FUNCTION__, chars);
	return chars;
}

static void edge_throttle (struct usb_serial_port *port)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct tty_struct *tty;
	int status;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return;

	tty = port->tty;
	if (!tty) {
		dbg ("%s - no tty available", __FUNCTION__);
		return;
	}

	/* if we are implementing XON/XOFF, send the stop character */
	if (I_IXOFF(tty)) {
		unsigned char stop_char = STOP_CHAR(tty);
		status = edge_write (port, &stop_char, 1);
		if (status <= 0) {
			dev_err(&port->dev, "%s - failed to write stop character, %d\n", __FUNCTION__, status);
		}
	}

	/* if we are implementing RTS/CTS, stop reads */
	/* and the Edgeport will clear the RTS line */
	if (C_CRTSCTS(tty))
		stop_read(edge_port);

}

static void edge_unthrottle (struct usb_serial_port *port)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct tty_struct *tty;
	int status;

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return;

	tty = port->tty;
	if (!tty) {
		dbg ("%s - no tty available", __FUNCTION__);
		return;
	}

	/* if we are implementing XON/XOFF, send the start character */
	if (I_IXOFF(tty)) {
		unsigned char start_char = START_CHAR(tty);
		status = edge_write (port, &start_char, 1);
		if (status <= 0) {
			dev_err(&port->dev, "%s - failed to write start character, %d\n", __FUNCTION__, status);
		}
	}

	/* if we are implementing RTS/CTS, restart reads */
	/* are the Edgeport will assert the RTS line */
	if (C_CRTSCTS(tty)) {
		status = restart_read(edge_port);
		if (status)
			dev_err(&port->dev, "%s - read bulk usb_submit_urb failed with value %d\n", __FUNCTION__, status);
	}

}

static void stop_read(struct edgeport_port *edge_port)
{
	unsigned long flags;

	spin_lock_irqsave(&edge_port->ep_lock, flags);

	if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
		edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPING;
	edge_port->shadow_mcr &= ~MCR_RTS;

	spin_unlock_irqrestore(&edge_port->ep_lock, flags);
}

static int restart_read(struct edgeport_port *edge_port)
{
	struct urb *urb;
	int status = 0;
	unsigned long flags;

	spin_lock_irqsave(&edge_port->ep_lock, flags);

	if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPED) {
		urb = edge_port->port->read_urb;
		urb->complete = edge_bulk_in_callback;
		urb->context = edge_port;
		urb->dev = edge_port->port->serial->dev;
		status = usb_submit_urb(urb, GFP_KERNEL);
	}
	edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING;
	edge_port->shadow_mcr |= MCR_RTS;

	spin_unlock_irqrestore(&edge_port->ep_lock, flags);

	return status;
}

static void change_port_settings (struct edgeport_port *edge_port, struct termios *old_termios)
{
	struct ump_uart_config *config;
	struct tty_struct *tty;
	int baud;
	unsigned cflag;
	int status;
	int port_number = edge_port->port->number - edge_port->port->serial->minor;

	dbg("%s - port %d", __FUNCTION__, edge_port->port->number);

	tty = edge_port->port->tty;
	if ((!tty) ||
	    (!tty->termios)) {
		dbg("%s - no tty structures", __FUNCTION__);
		return;
	}

	config = kmalloc (sizeof (*config), GFP_KERNEL);
	if (!config) {
		dev_err (&edge_port->port->dev, "%s - out of memory\n", __FUNCTION__);
		return;
	}

	cflag = tty->termios->c_cflag;

	config->wFlags = 0;

	/* These flags must be set */
	config->wFlags |= UMP_MASK_UART_FLAGS_RECEIVE_MS_INT;
	config->wFlags |= UMP_MASK_UART_FLAGS_AUTO_START_ON_ERR;
	config->bUartMode = (__u8)(edge_port->bUartMode);

	switch (cflag & CSIZE) {
		case CS5:
			    config->bDataBits = UMP_UART_CHAR5BITS;
			    dbg ("%s - data bits = 5", __FUNCTION__);
			    break;
		case CS6:
			    config->bDataBits = UMP_UART_CHAR6BITS;
			    dbg ("%s - data bits = 6", __FUNCTION__);
			    break;
		case CS7:
			    config->bDataBits = UMP_UART_CHAR7BITS;
			    dbg ("%s - data bits = 7", __FUNCTION__);
			    break;
		default:
		case CS8:
			    config->bDataBits = UMP_UART_CHAR8BITS;
			    dbg ("%s - data bits = 8", __FUNCTION__);
			    break;
	}

	if (cflag & PARENB) {
		if (cflag & PARODD) {
			config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
			config->bParity = UMP_UART_ODDPARITY;
			dbg("%s - parity = odd", __FUNCTION__);
		} else {
			config->wFlags |= UMP_MASK_UART_FLAGS_PARITY;
			config->bParity = UMP_UART_EVENPARITY;
			dbg("%s - parity = even", __FUNCTION__);
		}
	} else {
		config->bParity = UMP_UART_NOPARITY; 	
		dbg("%s - parity = none", __FUNCTION__);
	}

	if (cflag & CSTOPB) {
		config->bStopBits = UMP_UART_STOPBIT2;
		dbg("%s - stop bits = 2", __FUNCTION__);
	} else {
		config->bStopBits = UMP_UART_STOPBIT1;
		dbg("%s - stop bits = 1", __FUNCTION__);
	}

	/* figure out the flow control settings */
	if (cflag & CRTSCTS) {
		config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X_CTS_FLOW;
		config->wFlags |= UMP_MASK_UART_FLAGS_RTS_FLOW;
		dbg("%s - RTS/CTS is enabled", __FUNCTION__);
	} else {
		dbg("%s - RTS/CTS is disabled", __FUNCTION__);
		tty->hw_stopped = 0;
		restart_read(edge_port);
	}

	/* if we are implementing XON/XOFF, set the start and stop character in the device */
	if (I_IXOFF(tty) || I_IXON(tty)) {
		config->cXon  = START_CHAR(tty);
		config->cXoff = STOP_CHAR(tty);

		/* if we are implementing INBOUND XON/XOFF */
		if (I_IXOFF(tty)) {
			config->wFlags |= UMP_MASK_UART_FLAGS_IN_X;
			dbg ("%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x",
			     __FUNCTION__, config->cXon, config->cXoff);
		} else {
			dbg ("%s - INBOUND XON/XOFF is disabled", __FUNCTION__);
		}

		/* if we are implementing OUTBOUND XON/XOFF */
		if (I_IXON(tty)) {
			config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X;
			dbg ("%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x",
			     __FUNCTION__, config->cXon, config->cXoff);
		} else {
			dbg ("%s - OUTBOUND XON/XOFF is disabled", __FUNCTION__);
		}
	}

	/* Round the baud rate */
	baud = tty_get_baud_rate(tty);
	if (!baud) {
		/* pick a default, any default... */
		baud = 9600;
	}
	edge_port->baud_rate = baud;
	config->wBaudRate = (__u16)((461550L + baud/2) / baud);

	dbg ("%s - baud rate = %d, wBaudRate = %d", __FUNCTION__, baud, config->wBaudRate);

	dbg ("wBaudRate:   %d", (int)(461550L / config->wBaudRate));
	dbg ("wFlags:    0x%x", config->wFlags);
	dbg ("bDataBits:   %d", config->bDataBits);
	dbg ("bParity:     %d", config->bParity);
	dbg ("bStopBits:   %d", config->bStopBits);
	dbg ("cXon:        %d", config->cXon);
	dbg ("cXoff:       %d", config->cXoff);
	dbg ("bUartMode:   %d", config->bUartMode);

	/* move the word values into big endian mode */
	cpu_to_be16s (&config->wFlags);
	cpu_to_be16s (&config->wBaudRate);

	status = TIWriteCommandSync (edge_port->port->serial->dev,
				UMPC_SET_CONFIG,
				(__u8)(UMPM_UART1_PORT + port_number),
				0,
				(__u8 *)config,
				sizeof(*config));
	if (status) {
		dbg ("%s - error %d when trying to write config to device",
		     __FUNCTION__, status);
	}

	kfree (config);
	
	return;
}

static void edge_set_termios (struct usb_serial_port *port, struct termios *old_termios)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct tty_struct *tty = port->tty;
	unsigned int cflag;

	if (!port->tty || !port->tty->termios) {
		dbg ("%s - no tty or termios", __FUNCTION__);
		return;
	}

	cflag = tty->termios->c_cflag;
	/* check that they really want us to change something */
	if (old_termios) {
		if (cflag == old_termios->c_cflag &&
		    tty->termios->c_iflag == old_termios->c_iflag) {
			dbg ("%s - nothing to change", __FUNCTION__);
			return;
		}
	}

	dbg("%s - clfag %08x iflag %08x", __FUNCTION__, 
	    tty->termios->c_cflag, tty->termios->c_iflag);
	if (old_termios) {
		dbg("%s - old clfag %08x old iflag %08x", __FUNCTION__,
		    old_termios->c_cflag, old_termios->c_iflag);
	}

	dbg("%s - port %d", __FUNCTION__, port->number);

	if (edge_port == NULL)
		return;

	/* change the port settings to the new ones specified */
	change_port_settings (edge_port, old_termios);

	return;
}

static int edge_tiocmset (struct usb_serial_port *port, struct file *file, unsigned int set, unsigned int clear)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	unsigned int mcr;

	dbg("%s - port %d", __FUNCTION__, port->number);

	mcr = edge_port->shadow_mcr;
	if (set & TIOCM_RTS)
		mcr |= MCR_RTS;
	if (set & TIOCM_DTR)
		mcr |= MCR_DTR;
	if (set & TIOCM_LOOP)
		mcr |= MCR_LOOPBACK;

	if (clear & TIOCM_RTS)
		mcr &= ~MCR_RTS;
	if (clear & TIOCM_DTR)
		mcr &= ~MCR_DTR;
	if (clear & TIOCM_LOOP)
		mcr &= ~MCR_LOOPBACK;

	edge_port->shadow_mcr = mcr;

	TIRestoreMCR (edge_port, mcr);

	return 0;
}

static int edge_tiocmget(struct usb_serial_port *port, struct file *file)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	unsigned int result = 0;
	unsigned int msr;
	unsigned int mcr;

	dbg("%s - port %d", __FUNCTION__, port->number);

	msr = edge_port->shadow_msr;
	mcr = edge_port->shadow_mcr;
	result = ((mcr & MCR_DTR)	? TIOCM_DTR: 0)	  /* 0x002 */
		  | ((mcr & MCR_RTS)	? TIOCM_RTS: 0)   /* 0x004 */
		  | ((msr & EDGEPORT_MSR_CTS)	? TIOCM_CTS: 0)   /* 0x020 */
		  | ((msr & EDGEPORT_MSR_CD)	? TIOCM_CAR: 0)   /* 0x040 */
		  | ((msr & EDGEPORT_MSR_RI)	? TIOCM_RI:  0)   /* 0x080 */
		  | ((msr & EDGEPORT_MSR_DSR)	? TIOCM_DSR: 0);  /* 0x100 */


	dbg("%s -- %x", __FUNCTION__, result);

	return result;
}

static int get_serial_info (struct edgeport_port *edge_port, struct serial_struct __user *retinfo)
{
	struct serial_struct tmp;

	if (!retinfo)
		return -EFAULT;

	memset(&tmp, 0, sizeof(tmp));

	tmp.type		= PORT_16550A;
	tmp.line		= edge_port->port->serial->minor;
	tmp.port		= edge_port->port->number;
	tmp.irq			= 0;
	tmp.flags		= ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
	tmp.xmit_fifo_size	= edge_port->port->bulk_out_size;
	tmp.baud_base		= 9600;
	tmp.close_delay		= 5*HZ;
	tmp.closing_wait	= closing_wait;
//	tmp.custom_divisor	= state->custom_divisor;
//	tmp.hub6		= state->hub6;
//	tmp.io_type		= state->io_type;


	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
		return -EFAULT;
	return 0;
}

static int edge_ioctl (struct usb_serial_port *port, struct file *file, unsigned int cmd, unsigned long arg)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	struct async_icount cnow;
	struct async_icount cprev;

	dbg("%s - port %d, cmd = 0x%x", __FUNCTION__, port->number, cmd);

	switch (cmd) {
		case TIOCINQ:
			dbg("%s - (%d) TIOCINQ", __FUNCTION__, port->number);
//			return get_number_bytes_avail(edge_port, (unsigned int *) arg);
			break;

		case TIOCSERGETLSR:
			dbg("%s - (%d) TIOCSERGETLSR", __FUNCTION__, port->number);
//			return get_lsr_info(edge_port, (unsigned int *) arg);
			break;

		case TIOCGSERIAL:
			dbg("%s - (%d) TIOCGSERIAL", __FUNCTION__, port->number);
			return get_serial_info(edge_port, (struct serial_struct __user *) arg);
			break;

		case TIOCSSERIAL:
			dbg("%s - (%d) TIOCSSERIAL", __FUNCTION__, port->number);
			break;

		case TIOCMIWAIT:
			dbg("%s - (%d) TIOCMIWAIT", __FUNCTION__, port->number);
			cprev = edge_port->icount;
			while (1) {
				interruptible_sleep_on(&edge_port->delta_msr_wait);
				/* see if a signal did it */
				if (signal_pending(current))
					return -ERESTARTSYS;
				cnow = edge_port->icount;
				if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
				    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
					return -EIO; /* no change => error */
				if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
				    ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
				    ((arg & TIOCM_CD)  && (cnow.dcd != cprev.dcd)) ||
				    ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts)) ) {
					return 0;
				}
				cprev = cnow;
			}
			/* not reached */
			break;

		case TIOCGICOUNT:
			dbg ("%s - (%d) TIOCGICOUNT RX=%d, TX=%d", __FUNCTION__,
			     port->number, edge_port->icount.rx, edge_port->icount.tx);
			if (copy_to_user((void __user *)arg, &edge_port->icount, sizeof(edge_port->icount)))
				return -EFAULT;
			return 0;
	}

	return -ENOIOCTLCMD;
}

static void edge_break (struct usb_serial_port *port, int break_state)
{
	struct edgeport_port *edge_port = usb_get_serial_port_data(port);
	int status;

	dbg ("%s - state = %d", __FUNCTION__, break_state);

	/* chase the port close */
	TIChasePort (edge_port, 0, 0);

	if (break_state == -1) {
		status = TISetBreak (edge_port);
	} else {
		status = TIClearBreak (edge_port);
	}
	if (status) {
		dbg ("%s - error %d sending break set/clear command.",
		     __FUNCTION__, status);
	}
}

static int edge_startup (struct usb_serial *serial)
{
	struct edgeport_serial *edge_serial;
	struct edgeport_port *edge_port;
	struct usb_device *dev;
	int status;
	int i;

	dev = serial->dev;

	/* create our private serial structure */
	edge_serial = kmalloc (sizeof(struct edgeport_serial), GFP_KERNEL);
	if (edge_serial == NULL) {
		dev_err(&serial->dev->dev, "%s - Out of memory\n", __FUNCTION__);
		return -ENOMEM;
	}
	memset (edge_serial, 0, sizeof(struct edgeport_serial));
	sema_init(&edge_serial->es_sem, 1);
	edge_serial->serial = serial;
	usb_set_serial_data(serial, edge_serial);

	status = TIDownloadFirmware (edge_serial);
	if (status) {
		kfree (edge_serial);
		return status;
	}

	/* set up our port private structures */
	for (i = 0; i < serial->num_ports; ++i) {
		edge_port = kmalloc (sizeof(struct edgeport_port), GFP_KERNEL);
		if (edge_port == NULL) {
			dev_err(&serial->dev->dev, "%s - Out of memory\n", __FUNCTION__);
			goto cleanup;
		}
		memset (edge_port, 0, sizeof(struct edgeport_port));
		spin_lock_init(&edge_port->ep_lock);
		edge_port->ep_out_buf = edge_buf_alloc(EDGE_OUT_BUF_SIZE);
		if (edge_port->ep_out_buf == NULL) {
			dev_err(&serial->dev->dev, "%s - Out of memory\n", __FUNCTION__);
			kfree(edge_port);
			goto cleanup;
		}
		edge_port->port = serial->port[i];
		edge_port->edge_serial = edge_serial;
		usb_set_serial_port_data(serial->port[i], edge_port);
		edge_port->bUartMode = 0;	/* Default is RS232 */
	}
	
	return 0;

cleanup:
	for (--i; i>=0; --i) {
		edge_port = usb_get_serial_port_data(serial->port[i]);
		edge_buf_free(edge_port->ep_out_buf);
		kfree(edge_port);
		usb_set_serial_port_data(serial->port[i], NULL);
	}
	kfree (edge_serial);
	usb_set_serial_data(serial, NULL);
	return -ENOMEM;
}

static void edge_shutdown (struct usb_serial *serial)
{
	int i;
	struct edgeport_port *edge_port;

	dbg ("%s", __FUNCTION__);

	for (i=0; i < serial->num_ports; ++i) {
		edge_port = usb_get_serial_port_data(serial->port[i]);
		if (edge_port) {
			edge_buf_free(edge_port->ep_out_buf);
			kfree(edge_port);
		}
		usb_set_serial_port_data(serial->port[i], NULL);
	}
	kfree (usb_get_serial_data(serial));
	usb_set_serial_data(serial, NULL);
}


/* Circular Buffer */

/*
 * edge_buf_alloc
 *
 * Allocate a circular buffer and all associated memory.
 */

static struct edge_buf *edge_buf_alloc(unsigned int size)
{
	struct edge_buf *eb;


	if (size == 0)
		return NULL;

	eb = (struct edge_buf *)kmalloc(sizeof(struct edge_buf), GFP_KERNEL);
	if (eb == NULL)
		return NULL;

	eb->buf_buf = kmalloc(size, GFP_KERNEL);
	if (eb->buf_buf == NULL) {
		kfree(eb);
		return NULL;
	}

	eb->buf_size = size;
	eb->buf_get = eb->buf_put = eb->buf_buf;

	return eb;
}


/*
 * edge_buf_free
 *
 * Free the buffer and all associated memory.
 */

static void edge_buf_free(struct edge_buf *eb)
{
	if (eb) {
		kfree(eb->buf_buf);
		kfree(eb);
	}
}


/*
 * edge_buf_clear
 *
 * Clear out all data in the circular buffer.
 */

static void edge_buf_clear(struct edge_buf *eb)
{
        if (eb != NULL)
                eb->buf_get = eb->buf_put;
                /* equivalent to a get of all data available */
}


/*
 * edge_buf_data_avail
 *
 * Return the number of bytes of data available in the circular
 * buffer.
 */

static unsigned int edge_buf_data_avail(struct edge_buf *eb)
{
	if (eb != NULL)
		return ((eb->buf_size + eb->buf_put - eb->buf_get) % eb->buf_size);
	else
		return 0;
}


/*
 * edge_buf_space_avail
 *
 * Return the number of bytes of space available in the circular
 * buffer.
 */

static unsigned int edge_buf_space_avail(struct edge_buf *eb)
{
	if (eb != NULL)
		return ((eb->buf_size + eb->buf_get - eb->buf_put - 1) % eb->buf_size);
	else
		return 0;
}


/*
 * edge_buf_put
 *
 * Copy data data from a user buffer and put it into the circular buffer.
 * Restrict to the amount of space available.
 *
 * Return the number of bytes copied.
 */

static unsigned int edge_buf_put(struct edge_buf *eb, const char *buf,
	unsigned int count)
{
	unsigned int len;


	if (eb == NULL)
		return 0;

	len  = edge_buf_space_avail(eb);
	if (count > len)
		count = len;

	if (count == 0)
		return 0;

	len = eb->buf_buf + eb->buf_size - eb->buf_put;
	if (count > len) {
		memcpy(eb->buf_put, buf, len);
		memcpy(eb->buf_buf, buf+len, count - len);
		eb->buf_put = eb->buf_buf + count - len;
	} else {
		memcpy(eb->buf_put, buf, count);
		if (count < len)
			eb->buf_put += count;
		else /* count == len */
			eb->buf_put = eb->buf_buf;
	}

	return count;
}


/*
 * edge_buf_get
 *
 * Get data from the circular buffer and copy to the given buffer.
 * Restrict to the amount of data available.
 *
 * Return the number of bytes copied.
 */

static unsigned int edge_buf_get(struct edge_buf *eb, char *buf,
	unsigned int count)
{
	unsigned int len;


	if (eb == NULL)
		return 0;

	len = edge_buf_data_avail(eb);
	if (count > len)
		count = len;

	if (count == 0)
		return 0;

	len = eb->buf_buf + eb->buf_size - eb->buf_get;
	if (count > len) {
		memcpy(buf, eb->buf_get, len);
		memcpy(buf+len, eb->buf_buf, count - len);
		eb->buf_get = eb->buf_buf + count - len;
	} else {
		memcpy(buf, eb->buf_get, count);
		if (count < len)
			eb->buf_get += count;
		else /* count == len */
			eb->buf_get = eb->buf_buf;
	}

	return count;
}


static struct usb_serial_driver edgeport_1port_device = {
	.driver = {
		.owner		= THIS_MODULE,
		.name		= "edgeport_ti_1",
	},
	.description		= "Edgeport TI 1 port adapter",
	.id_table		= edgeport_1port_id_table,
	.num_interrupt_in	= 1,
	.num_bulk_in		= 1,
	.num_bulk_out		= 1,
	.num_ports		= 1,
	.open			= edge_open,
	.close			= edge_close,
	.throttle		= edge_throttle,
	.unthrottle		= edge_unthrottle,
	.attach			= edge_startup,
	.shutdown		= edge_shutdown,
	.ioctl			= edge_ioctl,
	.set_termios		= edge_set_termios,
	.tiocmget		= edge_tiocmget,
	.tiocmset		= edge_tiocmset,
	.write			= edge_write,
	.write_room		= edge_write_room,
	.chars_in_buffer	= edge_chars_in_buffer,
	.break_ctl		= edge_break,
	.read_int_callback	= edge_interrupt_callback,
	.read_bulk_callback	= edge_bulk_in_callback,
	.write_bulk_callback	= edge_bulk_out_callback,
};

static struct usb_serial_driver edgeport_2port_device = {
	.driver = {
		.owner		= THIS_MODULE,
		.name		= "edgeport_ti_2",
	},
	.description		= "Edgeport TI 2 port adapter",
	.id_table		= edgeport_2port_id_table,
	.num_interrupt_in	= 1,
	.num_bulk_in		= 2,
	.num_bulk_out		= 2,
	.num_ports		= 2,
	.open			= edge_open,
	.close			= edge_close,
	.throttle		= edge_throttle,
	.unthrottle		= edge_unthrottle,
	.attach			= edge_startup,
	.shutdown		= edge_shutdown,
	.ioctl			= edge_ioctl,
	.set_termios		= edge_set_termios,
	.tiocmget		= edge_tiocmget,
	.tiocmset		= edge_tiocmset,
	.write			= edge_write,
	.write_room		= edge_write_room,
	.chars_in_buffer	= edge_chars_in_buffer,
	.break_ctl		= edge_break,
	.read_int_callback	= edge_interrupt_callback,
	.read_bulk_callback	= edge_bulk_in_callback,
	.write_bulk_callback	= edge_bulk_out_callback,
};


static int __init edgeport_init(void)
{
	int retval;
	retval = usb_serial_register(&edgeport_1port_device);
	if (retval)
		goto failed_1port_device_register;
	retval = usb_serial_register(&edgeport_2port_device);
	if (retval)
		goto failed_2port_device_register;
	retval = usb_register(&io_driver);
	if (retval) 
		goto failed_usb_register;
	info(DRIVER_DESC " " DRIVER_VERSION);
	return 0;
failed_usb_register:
	usb_serial_deregister(&edgeport_2port_device);
failed_2port_device_register:
	usb_serial_deregister(&edgeport_1port_device);
failed_1port_device_register:
	return retval;
}

static void __exit edgeport_exit (void)
{
	usb_deregister (&io_driver);
	usb_serial_deregister (&edgeport_1port_device);
	usb_serial_deregister (&edgeport_2port_device);
}

module_init(edgeport_init);
module_exit(edgeport_exit);

/* Module information */
MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");

module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Debug enabled or not");

module_param(low_latency, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(low_latency, "Low latency enabled or not");

module_param(closing_wait, int, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(closing_wait, "Maximum wait for data to drain, in .01 secs");

module_param(ignore_cpu_rev, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(ignore_cpu_rev, "Ignore the cpu revision when connecting to a device");