/*
 *  Native support for the Aiptek HyperPen USB Tablets
 *  (4000U/5000U/6000U/8000U/12000U)
 *  
 *  Copyright (c) 2001      Chris Atenasio   <chris@crud.net>
 *  Copyright (c) 2002-2004 Bryan W. Headley <bwheadley@earthlink.net>
 *
 *  based on wacom.c by
 *     Vojtech Pavlik      <vojtech@suse.cz>
 *     Andreas Bach Aaen   <abach@stofanet.dk>
 *     Clifford Wolf       <clifford@clifford.at>
 *     Sam Mosel           <sam.mosel@computer.org>
 *     James E. Blair      <corvus@gnu.org>
 *     Daniel Egger        <egger@suse.de>
 *
 *  Many thanks to Oliver Kuechemann for his support.
 *
 *  ChangeLog:
 *      v0.1 - Initial release
 *      v0.2 - Hack to get around fake event 28's. (Bryan W. Headley)
 *      v0.3 - Make URB dynamic (Bryan W. Headley, Jun-8-2002)
 *             Released to Linux 2.4.19 and 2.5.x
 *      v0.4 - Rewrote substantial portions of the code to deal with
 *             corrected control sequences, timing, dynamic configuration,
 *             support of 6000U - 12000U, procfs, and macro key support
 *             (Jan-1-2003 - Feb-5-2003, Bryan W. Headley)
 *      v1.0 - Added support for diagnostic messages, count of messages
 *             received from URB - Mar-8-2003, Bryan W. Headley
 *      v1.1 - added support for tablet resolution, changed DV and proximity
 *             some corrections - Jun-22-2003, martin schneebacher
 *           - Added support for the sysfs interface, deprecating the
 *             procfs interface for 2.5.x kernel. Also added support for
 *             Wheel command. Bryan W. Headley July-15-2003.
 *      v1.2 - Reworked jitter timer as a kernel thread. 
 *             Bryan W. Headley November-28-2003/Jan-10-2004.
 *      v1.3 - Repaired issue of kernel thread going nuts on single-processor
 *             machines, introduced programmableDelay as a command line
 *             parameter. Feb 7 2004, Bryan W. Headley.
 *      v1.4 - Re-wire jitter so it does not require a thread. Courtesy of
 *             Rene van Paassen. Added reporting of physical pointer device
 *             (e.g., stylus, mouse in reports 2, 3, 4, 5. We don't know
 *             for reports 1, 6.)
 *             what physical device reports for reports 1, 6.) Also enabled
 *             MOUSE and LENS tool button modes. Renamed "rubber" to "eraser".
 *             Feb 20, 2004, Bryan W. Headley.
 *      v1.5 - Added previousJitterable, so we don't do jitter delay when the
 *             user is holding a button down for periods of time.
 *
 * NOTE:
 *      This kernel driver is augmented by the "Aiptek" XFree86 input
 *      driver for your X server, as well as the Gaiptek GUI Front-end
 *      "Tablet Manager". 
 *      These three products are highly interactive with one another, 
 *      so therefore it's easier to document them all as one subsystem.
 *      Please visit the project's "home page", located at, 
 *      http://aiptektablet.sourceforge.net.
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
 */

#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/input.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/usb.h>
#include <linux/sched.h>
#include <asm/uaccess.h>
#include <asm/unaligned.h>

/*
 * Version Information
 */
#define DRIVER_VERSION "v1.5 (May-15-2004)"
#define DRIVER_AUTHOR  "Bryan W. Headley/Chris Atenasio"
#define DRIVER_DESC    "Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)"

/*
 * Aiptek status packet:
 *
 * (returned as Report 1 - relative coordinates from mouse and stylus)
 *
 *        bit7  bit6  bit5  bit4  bit3  bit2  bit1  bit0
 * byte0   0     0     0     0     0     0     0     1
 * byte1   0     0     0     0     0    BS2   BS    Tip
 * byte2  X7    X6    X5    X4    X3    X2    X1    X0
 * byte3  Y7    Y6    Y5    Y4    Y3    Y2    Y1    Y0
 *
 * (returned as Report 2 - absolute coordinates from the stylus)
 *
 *        bit7  bit6  bit5  bit4  bit3  bit2  bit1  bit0
 * byte0   0     0     0     0     0     0     1     0
 * byte1  X7    X6    X5    X4    X3    X2    X1    X0
 * byte2  X15   X14   X13   X12   X11   X10   X9    X8
 * byte3  Y7    Y6    Y5    Y4    Y3    Y2    Y1    Y0
 * byte4  Y15   Y14   Y13   Y12   Y11   Y10   Y9    Y8
 * byte5   *     *     *    BS2   BS1   Tip   IR    DV
 * byte6  P7    P6    P5    P4    P3    P2    P1    P0
 * byte7  P15   P14   P13   P12   P11   P10   P9    P8
 *
 * (returned as Report 3 - absolute coordinates from the mouse)
 *
 *        bit7  bit6  bit5  bit4  bit3  bit2  bit1  bit0
 * byte0   0     0     0     0     0     0     1     0
 * byte1  X7    X6    X5    X4    X3    X2    X1    X0
 * byte2  X15   X14   X13   X12   X11   X10   X9    X8
 * byte3  Y7    Y6    Y5    Y4    Y3    Y2    Y1    Y0
 * byte4  Y15   Y14   Y13   Y12   Y11   Y10   Y9    Y8
 * byte5   *     *     *    BS2   BS1   Tip   IR    DV
 * byte6  P7    P6    P5    P4    P3    P2    P1    P0
 * byte7  P15   P14   P13   P12   P11   P10   P9    P8
 *
 * (returned as Report 4 - macrokeys from the stylus)
 *
 *        bit7  bit6  bit5  bit4  bit3  bit2  bit1  bit0
 * byte0   0     0     0     0     0     1     0     0
 * byte1   0     0     0    BS2   BS    Tip   IR    DV
 * byte2   0     0     0     0     0     0     1     0
 * byte3   0     0     0    K4    K3    K2    K1    K0
 * byte4  P7    P6    P5    P4    P3    P2    P1    P0
 * byte5  P15   P14   P13   P12   P11   P10   P9    P8
 *
 * (returned as Report 5 - macrokeys from the mouse)
 *
 *        bit7  bit6  bit5  bit4  bit3  bit2  bit1  bit0
 * byte0   0     0     0     0     0     1     0     0
 * byte1   0     0     0    BS2   BS    Tip   IR    DV
 * byte2   0     0     0     0     0     0     1     0
 * byte3   0     0     0    K4    K3    K2    K1    K0
 * byte4  P7    P6    P5    P4    P3    P2    P1    P0
 * byte5  P15   P14   P13   P12   P11   P10   P9    P8
 *
 * IR: In Range = Proximity on
 * DV = Data Valid
 * BS = Barrel Switch (as in, macro keys)
 * BS2 also referred to as Tablet Pick
 *
 * Command Summary:
 *
 * Use report_type CONTROL (3)
 * Use report_id   2
 *
 * Command/Data    Description     Return Bytes    Return Value
 * 0x10/0x00       SwitchToMouse       0
 * 0x10/0x01       SwitchToTablet      0
 * 0x18/0x04       SetResolution       0 
 * 0x12/0xFF       AutoGainOn          0
 * 0x17/0x00       FilterOn            0
 * 0x01/0x00       GetXExtension       2           MaxX
 * 0x01/0x01       GetYExtension       2           MaxY
 * 0x02/0x00       GetModelCode        2           ModelCode = LOBYTE
 * 0x03/0x00       GetODMCode          2           ODMCode
 * 0x08/0x00       GetPressureLevels   2           =512
 * 0x04/0x00       GetFirmwareVersion  2           Firmware Version
 * 0x11/0x02       EnableMacroKeys     0
 *
 * To initialize the tablet:
 *
 * (1) Send Resolution500LPI (Command)
 * (2) Query for Model code (Option Report)
 * (3) Query for ODM code (Option Report)
 * (4) Query for firmware (Option Report)
 * (5) Query for GetXExtension (Option Report)
 * (6) Query for GetYExtension (Option Report)
 * (7) Query for GetPressureLevels (Option Report)
 * (8) SwitchToTablet for Absolute coordinates, or
 *     SwitchToMouse for Relative coordinates (Command)
 * (9) EnableMacroKeys (Command)
 * (10) FilterOn (Command)
 * (11) AutoGainOn (Command)
 *
 * (Step 9 can be omitted, but you'll then have no function keys.)
 */

#define USB_VENDOR_ID_AIPTEK				0x08ca
#define USB_REQ_GET_REPORT				0x01
#define USB_REQ_SET_REPORT				0x09

	/* PointerMode codes
	 */
#define AIPTEK_POINTER_ONLY_MOUSE_MODE			0
#define AIPTEK_POINTER_ONLY_STYLUS_MODE			1
#define AIPTEK_POINTER_EITHER_MODE			2

#define AIPTEK_POINTER_ALLOW_MOUSE_MODE(a)		\
	(a == AIPTEK_POINTER_ONLY_MOUSE_MODE ||		\
	 a == AIPTEK_POINTER_EITHER_MODE)
#define AIPTEK_POINTER_ALLOW_STYLUS_MODE(a)		\
	(a == AIPTEK_POINTER_ONLY_STYLUS_MODE ||	\
	 a == AIPTEK_POINTER_EITHER_MODE)

	/* CoordinateMode code
	 */
#define AIPTEK_COORDINATE_RELATIVE_MODE			0
#define AIPTEK_COORDINATE_ABSOLUTE_MODE			1

       /* XTilt and YTilt values
        */
#define AIPTEK_TILT_MIN					(-128)
#define AIPTEK_TILT_MAX					127
#define AIPTEK_TILT_DISABLE				(-10101)

	/* Wheel values
	 */
#define AIPTEK_WHEEL_MIN				0
#define AIPTEK_WHEEL_MAX				1024
#define AIPTEK_WHEEL_DISABLE				(-10101)

	/* ToolCode values, which BTW are 0x140 .. 0x14f
	 * We have things set up such that if TOOL_BUTTON_FIRED_BIT is
	 * not set, we'll send one instance of AIPTEK_TOOL_BUTTON_xxx.
	 *
	 * Whenever the user resets the value, TOOL_BUTTON_FIRED_BIT will
	 * get reset.
	 */
#define TOOL_BUTTON(x)					((x) & 0x14f)
#define TOOL_BUTTON_FIRED(x)				((x) & 0x200)
#define TOOL_BUTTON_FIRED_BIT				0x200
	/* toolMode codes
	 */
#define AIPTEK_TOOL_BUTTON_PEN_MODE			BTN_TOOL_PEN
#define AIPTEK_TOOL_BUTTON_PEN_MODE			BTN_TOOL_PEN
#define AIPTEK_TOOL_BUTTON_PENCIL_MODE			BTN_TOOL_PENCIL
#define AIPTEK_TOOL_BUTTON_BRUSH_MODE			BTN_TOOL_BRUSH
#define AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE		BTN_TOOL_AIRBRUSH
#define AIPTEK_TOOL_BUTTON_ERASER_MODE			BTN_TOOL_RUBBER
#define AIPTEK_TOOL_BUTTON_MOUSE_MODE			BTN_TOOL_MOUSE
#define AIPTEK_TOOL_BUTTON_LENS_MODE			BTN_TOOL_LENS

	/* Diagnostic message codes
	 */
#define AIPTEK_DIAGNOSTIC_NA				0
#define AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE	1
#define AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE	2
#define AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED		3

	/* Time to wait (in ms) to help mask hand jittering 
	 * when pressing the stylus buttons.
	 */
#define AIPTEK_JITTER_DELAY_DEFAULT			50

	/* Time to wait (in ms) in-between sending the tablet
	 * a command and beginning the process of reading the return
	 * sequence from the tablet.
	 */
#define AIPTEK_PROGRAMMABLE_DELAY_25		25
#define AIPTEK_PROGRAMMABLE_DELAY_50		50
#define AIPTEK_PROGRAMMABLE_DELAY_100		100
#define AIPTEK_PROGRAMMABLE_DELAY_200		200
#define AIPTEK_PROGRAMMABLE_DELAY_300		300
#define AIPTEK_PROGRAMMABLE_DELAY_400		400
#define AIPTEK_PROGRAMMABLE_DELAY_DEFAULT	AIPTEK_PROGRAMMABLE_DELAY_400

	/* Mouse button programming
	 */
#define AIPTEK_MOUSE_LEFT_BUTTON		0x01
#define AIPTEK_MOUSE_RIGHT_BUTTON		0x02
#define AIPTEK_MOUSE_MIDDLE_BUTTON		0x04

	/* Stylus button programming
	 */
#define AIPTEK_STYLUS_LOWER_BUTTON		0x08
#define AIPTEK_STYLUS_UPPER_BUTTON		0x10

	/* Length of incoming packet from the tablet
	 */
#define AIPTEK_PACKET_LENGTH			8

	/* We report in EV_MISC both the proximity and
	 * whether the report came from the stylus, tablet mouse
	 * or "unknown" -- Unknown when the tablet is in relative
	 * mode, because we only get report 1's.
	 */
#define AIPTEK_REPORT_TOOL_UNKNOWN		0x10
#define AIPTEK_REPORT_TOOL_STYLUS		0x20
#define AIPTEK_REPORT_TOOL_MOUSE		0x40

static int programmableDelay = AIPTEK_PROGRAMMABLE_DELAY_DEFAULT;
static int jitterDelay = AIPTEK_JITTER_DELAY_DEFAULT;

struct aiptek_features {
	int odmCode;		/* Tablet manufacturer code       */
	int modelCode;		/* Tablet model code (not unique) */
	int firmwareCode;	/* prom/eeprom version            */
	char usbPath[64 + 1];	/* device's physical usb path     */
	char inputPath[64 + 1];	/* input device path              */
};

struct aiptek_settings {
	int pointerMode;	/* stylus-, mouse-only or either */
	int coordinateMode;	/* absolute/relative coords      */
	int toolMode;		/* pen, pencil, brush, etc. tool */
	int xTilt;		/* synthetic xTilt amount        */
	int yTilt;		/* synthetic yTilt amount        */
	int wheel;		/* synthetic wheel amount        */
	int stylusButtonUpper;	/* stylus upper btn delivers...  */
	int stylusButtonLower;	/* stylus lower btn delivers...  */
	int mouseButtonLeft;	/* mouse left btn delivers...    */
	int mouseButtonMiddle;	/* mouse middle btn delivers...  */
	int mouseButtonRight;	/* mouse right btn delivers...   */
	int programmableDelay;	/* delay for tablet programming  */
	int jitterDelay;	/* delay for hand jittering      */
};

struct aiptek {
	struct input_dev inputdev;		/* input device struct           */
	struct usb_device *usbdev;		/* usb device struct             */
	struct urb *urb;			/* urb for incoming reports      */
	dma_addr_t data_dma;			/* our dma stuffage              */
	struct aiptek_features features;	/* tablet's array of features    */
	struct aiptek_settings curSetting;	/* tablet's current programmable */
	struct aiptek_settings newSetting;	/* ... and new param settings    */
	unsigned int ifnum;			/* interface number for IO       */
	int openCount;				/* module use counter            */
	int diagnostic;				/* tablet diagnostic codes       */
	unsigned long eventCount;		/* event count                   */
	int inDelay;				/* jitter: in jitter delay?      */
	unsigned long endDelay;			/* jitter: time when delay ends  */
	int previousJitterable;			/* jitterable prev value     */
	unsigned char *data;			/* incoming packet data          */
};

/*
 * Permit easy lookup of keyboard events to send, versus
 * the bitmap which comes from the tablet. This hides the
 * issue that the F_keys are not sequentially numbered.
 */
static int macroKeyEvents[] = {
	KEY_ESC, KEY_F1, KEY_F2, KEY_F3, KEY_F4, KEY_F5,
	KEY_F6, KEY_F7, KEY_F8, KEY_F9, KEY_F10, KEY_F11,
	KEY_F12, KEY_F13, KEY_F14, KEY_F15, KEY_F16, KEY_F17,
	KEY_F18, KEY_F19, KEY_F20, KEY_F21, KEY_F22, KEY_F23,
	KEY_F24, KEY_STOP, KEY_AGAIN, KEY_PROPS, KEY_UNDO,
	KEY_FRONT, KEY_COPY, KEY_OPEN, KEY_PASTE, 0
};

/***********************************************************************
 * Relative reports deliver values in 2's complement format to
 * deal with negative offsets.
 */
static int aiptek_convert_from_2s_complement(unsigned char c)
{
	int ret;
	unsigned char b = c;
	int negate = 0;

	if ((b & 0x80) != 0) {
		b = ~b;
		b--;
		negate = 1;
	}
	ret = b;
	ret = (negate == 1) ? -ret : ret;
	return ret;
}

/***********************************************************************
 * aiptek_irq can receive one of six potential reports.
 * The documentation for each is in the body of the function.
 *
 * The tablet reports on several attributes per invocation of
 * aiptek_irq. Because the Linux Input Event system allows the
 * transmission of ONE attribute per input_report_xxx() call,
 * collation has to be done on the other end to reconstitute
 * a complete tablet report. Further, the number of Input Event reports
 * submitted varies, depending on what USB report type, and circumstance.
 * To deal with this, EV_MSC is used to indicate an 'end-of-report'
 * message. This has been an undocumented convention understood by the kernel
 * tablet driver and clients such as gpm and XFree86's tablet drivers.
 *
 * Of the information received from the tablet, the one piece I
 * cannot transmit is the proximity bit (without resorting to an EV_MSC
 * convention above.) I therefore have taken over REL_MISC and ABS_MISC
 * (for relative and absolute reports, respectively) for communicating
 * Proximity. Why two events? I thought it interesting to know if the
 * Proximity event occured while the tablet was in absolute or relative
 * mode.
 *
 * Other tablets use the notion of a certain minimum stylus pressure
 * to infer proximity. While that could have been done, that is yet
 * another 'by convention' behavior, the documentation for which
 * would be spread between two (or more) pieces of software.
 *
 * EV_MSC usage was terminated for this purpose in Linux 2.5.x, and
 * replaced with the input_sync() method (which emits EV_SYN.)
 */

static void aiptek_irq(struct urb *urb, struct pt_regs *regs)
{
	struct aiptek *aiptek = urb->context;
	unsigned char *data = aiptek->data;
	struct input_dev *inputdev = &aiptek->inputdev;
	int jitterable = 0;
	int retval, macro, x, y, z, left, right, middle, p, dv, tip, bs, pck;

	switch (urb->status) {
	case 0:
		/* Success */
		break;

	case -ECONNRESET:
	case -ENOENT:
	case -ESHUTDOWN:
		/* This urb is terminated, clean up */
		dbg("%s - urb shutting down with status: %d",
		    __FUNCTION__, urb->status);
		return;

	default:
		dbg("%s - nonzero urb status received: %d",
		    __FUNCTION__, urb->status);
		goto exit;
	}

	/* See if we are in a delay loop -- throw out report if true.
	 */
	if (aiptek->inDelay == 1 && time_after(aiptek->endDelay, jiffies)) {
		goto exit;
	}

	aiptek->inDelay = 0;
	aiptek->eventCount++;

	/* Report 1 delivers relative coordinates with either a stylus
	 * or the mouse. You do not know, however, which input
	 * tool generated the event.
	 */
	if (data[0] == 1) {
		if (aiptek->curSetting.coordinateMode ==
		    AIPTEK_COORDINATE_ABSOLUTE_MODE) {
			aiptek->diagnostic =
			    AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE;
		} else {
			input_regs(inputdev, regs);

			x = aiptek_convert_from_2s_complement(data[2]);
			y = aiptek_convert_from_2s_complement(data[3]);

			/* jitterable keeps track of whether any button has been pressed.
			 * We're also using it to remap the physical mouse button mask
			 * to pseudo-settings. (We don't specifically care about it's
			 * value after moving/transposing mouse button bitmasks, except
			 * that a non-zero value indicates that one or more
			 * mouse button was pressed.)
			 */
			jitterable = data[5] & 0x07;

			left = (data[5] & aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
			right = (data[5] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
			middle = (data[5] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;

			input_report_key(inputdev, BTN_LEFT, left);
			input_report_key(inputdev, BTN_MIDDLE, middle);
			input_report_key(inputdev, BTN_RIGHT, right);
			input_report_rel(inputdev, REL_X, x);
			input_report_rel(inputdev, REL_Y, y);
			input_report_rel(inputdev, REL_MISC, 1 | AIPTEK_REPORT_TOOL_UNKNOWN);

			/* Wheel support is in the form of a single-event
			 * firing.
			 */
			if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
				input_report_rel(inputdev, REL_WHEEL,
						 aiptek->curSetting.wheel);
				aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
			}
			input_sync(inputdev);
		}
	}
	/* Report 2 is delivered only by the stylus, and delivers
	 * absolute coordinates.
	 */
	else if (data[0] == 2) {
		if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
			aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
		} else if (!AIPTEK_POINTER_ALLOW_STYLUS_MODE
			    (aiptek->curSetting.pointerMode)) {
				aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
		} else {
			input_regs(inputdev, regs);

			x = le16_to_cpu(get_unaligned((__le16 *) (data + 1)));
			y = le16_to_cpu(get_unaligned((__le16 *) (data + 3)));
			z = le16_to_cpu(get_unaligned((__le16 *) (data + 6)));

			p = (data[5] & 0x01) != 0 ? 1 : 0;
			dv = (data[5] & 0x02) != 0 ? 1 : 0;
			tip = (data[5] & 0x04) != 0 ? 1 : 0;

			/* Use jitterable to re-arrange button masks
			 */
			jitterable = data[5] & 0x18;

			bs = (data[5] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
			pck = (data[5] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;

			/* dv indicates 'data valid' (e.g., the tablet is in sync
			 * and has delivered a "correct" report) We will ignore
			 * all 'bad' reports...
			 */
			if (dv != 0) {
				/* If we've not already sent a tool_button_?? code, do
				 * so now. Then set FIRED_BIT so it won't be resent unless
				 * the user forces FIRED_BIT off.
				 */
				if (TOOL_BUTTON_FIRED
				    (aiptek->curSetting.toolMode) == 0) {
					input_report_key(inputdev,
							 TOOL_BUTTON(aiptek->curSetting.toolMode),
							 1);
					aiptek->curSetting.toolMode |= TOOL_BUTTON_FIRED_BIT;
				}

				if (p != 0) {
					input_report_abs(inputdev, ABS_X, x);
					input_report_abs(inputdev, ABS_Y, y);
					input_report_abs(inputdev, ABS_PRESSURE, z);

					input_report_key(inputdev, BTN_TOUCH, tip);
					input_report_key(inputdev, BTN_STYLUS, bs);
					input_report_key(inputdev, BTN_STYLUS2, pck);

					if (aiptek->curSetting.xTilt !=
					    AIPTEK_TILT_DISABLE) {
						input_report_abs(inputdev,
								 ABS_TILT_X,
								 aiptek->curSetting.xTilt);
					}
					if (aiptek->curSetting.yTilt != AIPTEK_TILT_DISABLE) {
						input_report_abs(inputdev,
								 ABS_TILT_Y,
								 aiptek->curSetting.yTilt);
					}

					/* Wheel support is in the form of a single-event
					 * firing.
					 */
					if (aiptek->curSetting.wheel !=
					    AIPTEK_WHEEL_DISABLE) {
						input_report_abs(inputdev,
								 ABS_WHEEL,
								 aiptek->curSetting.wheel);
						aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
					}
				}
				input_report_abs(inputdev, ABS_MISC, p | AIPTEK_REPORT_TOOL_STYLUS);
				input_sync(inputdev);
			}
		}
	}
	/* Report 3's come from the mouse in absolute mode.
	 */
	else if (data[0] == 3) {
		if (aiptek->curSetting.coordinateMode == AIPTEK_COORDINATE_RELATIVE_MODE) {
			aiptek->diagnostic = AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE;
		} else if (!AIPTEK_POINTER_ALLOW_MOUSE_MODE
			(aiptek->curSetting.pointerMode)) {
			aiptek->diagnostic = AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED;
		} else {
			input_regs(inputdev, regs);
			x = le16_to_cpu(get_unaligned((__le16 *) (data + 1)));
			y = le16_to_cpu(get_unaligned((__le16 *) (data + 3)));

			jitterable = data[5] & 0x1c;

			p = (data[5] & 0x01) != 0 ? 1 : 0;
			dv = (data[5] & 0x02) != 0 ? 1 : 0;
			left = (data[5] & aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
			right = (data[5] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
			middle = (data[5] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;

			if (dv != 0) {
				/* If we've not already sent a tool_button_?? code, do
				 * so now. Then set FIRED_BIT so it won't be resent unless
				 * the user forces FIRED_BIT off.
				 */
				if (TOOL_BUTTON_FIRED
				    (aiptek->curSetting.toolMode) == 0) {
					input_report_key(inputdev,
							 TOOL_BUTTON(aiptek->curSetting.toolMode),
							 1);
					aiptek->curSetting.toolMode |= TOOL_BUTTON_FIRED_BIT;
				}

				if (p != 0) {
					input_report_abs(inputdev, ABS_X, x);
					input_report_abs(inputdev, ABS_Y, y);

					input_report_key(inputdev, BTN_LEFT, left);
					input_report_key(inputdev, BTN_MIDDLE, middle);
					input_report_key(inputdev, BTN_RIGHT, right);

					/* Wheel support is in the form of a single-event
					 * firing.
					 */
					if (aiptek->curSetting.wheel != AIPTEK_WHEEL_DISABLE) {
						input_report_abs(inputdev,
								 ABS_WHEEL,
								 aiptek->curSetting.wheel);
						aiptek->curSetting.wheel = AIPTEK_WHEEL_DISABLE;
					}
				}
				input_report_rel(inputdev, REL_MISC, p | AIPTEK_REPORT_TOOL_MOUSE);
				input_sync(inputdev);
			}
		}
	}
	/* Report 4s come from the macro keys when pressed by stylus
	 */
	else if (data[0] == 4) {
		jitterable = data[1] & 0x18;

		p = (data[1] & 0x01) != 0 ? 1 : 0;
		dv = (data[1] & 0x02) != 0 ? 1 : 0;
		tip = (data[1] & 0x04) != 0 ? 1 : 0;
		bs = (data[1] & aiptek->curSetting.stylusButtonLower) != 0 ? 1 : 0;
		pck = (data[1] & aiptek->curSetting.stylusButtonUpper) != 0 ? 1 : 0;

		macro = data[3];
		z = le16_to_cpu(get_unaligned((__le16 *) (data + 4)));

		if (dv != 0) {
			input_regs(inputdev, regs);

			/* If we've not already sent a tool_button_?? code, do
			 * so now. Then set FIRED_BIT so it won't be resent unless
			 * the user forces FIRED_BIT off.
			 */
			if (TOOL_BUTTON_FIRED(aiptek->curSetting.toolMode) == 0) {
				input_report_key(inputdev,
						 TOOL_BUTTON(aiptek->curSetting.toolMode),
						 1);
				aiptek->curSetting.toolMode |= TOOL_BUTTON_FIRED_BIT;
			}

			if (p != 0) {
				input_report_key(inputdev, BTN_TOUCH, tip);
				input_report_key(inputdev, BTN_STYLUS, bs);
				input_report_key(inputdev, BTN_STYLUS2, pck);
				input_report_abs(inputdev, ABS_PRESSURE, z);
			}

			/* For safety, we're sending key 'break' codes for the
			 * neighboring macro keys.
			 */
			if (macro > 0) {
				input_report_key(inputdev,
						 macroKeyEvents[macro - 1], 0);
			}
			if (macro < 25) {
				input_report_key(inputdev,
						 macroKeyEvents[macro + 1], 0);
			}
			input_report_key(inputdev, macroKeyEvents[macro], p);
			input_report_abs(inputdev, ABS_MISC,
					 p | AIPTEK_REPORT_TOOL_STYLUS);
			input_sync(inputdev);
		}
	}
	/* Report 5s come from the macro keys when pressed by mouse
	 */
	else if (data[0] == 5) {
		jitterable = data[1] & 0x1c;

		p = (data[1] & 0x01) != 0 ? 1 : 0;
		dv = (data[1] & 0x02) != 0 ? 1 : 0;
		left = (data[1]& aiptek->curSetting.mouseButtonLeft) != 0 ? 1 : 0;
		right = (data[1] & aiptek->curSetting.mouseButtonRight) != 0 ? 1 : 0;
		middle = (data[1] & aiptek->curSetting.mouseButtonMiddle) != 0 ? 1 : 0;
		macro = data[3];

		if (dv != 0) {
			input_regs(inputdev, regs);

			/* If we've not already sent a tool_button_?? code, do
			 * so now. Then set FIRED_BIT so it won't be resent unless
			 * the user forces FIRED_BIT off.
			 */
			if (TOOL_BUTTON_FIRED(aiptek->curSetting.toolMode) == 0) {
				input_report_key(inputdev,
						 TOOL_BUTTON(aiptek->curSetting.toolMode),
						 1);
				aiptek->curSetting.toolMode |= TOOL_BUTTON_FIRED_BIT;
			}

			if (p != 0) {
				input_report_key(inputdev, BTN_LEFT, left);
				input_report_key(inputdev, BTN_MIDDLE, middle);
				input_report_key(inputdev, BTN_RIGHT, right);
			}

			/* For safety, we're sending key 'break' codes for the
			 * neighboring macro keys.
			 */
			if (macro > 0) {
				input_report_key(inputdev,
						 macroKeyEvents[macro - 1], 0);
			}
			if (macro < 25) {
				input_report_key(inputdev,
						 macroKeyEvents[macro + 1], 0);
			}

			input_report_key(inputdev, macroKeyEvents[macro], 1);
			input_report_rel(inputdev, ABS_MISC,
					 p | AIPTEK_REPORT_TOOL_MOUSE);
			input_sync(inputdev);
		}
	}
	/* We have no idea which tool can generate a report 6. Theoretically,
	 * neither need to, having been given reports 4 & 5 for such use.
	 * However, report 6 is the 'official-looking' report for macroKeys;
	 * reports 4 & 5 supposively are used to support unnamed, unknown
	 * hat switches (which just so happen to be the macroKeys.)
	 */
	else if (data[0] == 6) {
		macro = le16_to_cpu(get_unaligned((__le16 *) (data + 1)));
		input_regs(inputdev, regs);

		if (macro > 0) {
			input_report_key(inputdev, macroKeyEvents[macro - 1],
					 0);
		}
		if (macro < 25) {
			input_report_key(inputdev, macroKeyEvents[macro + 1],
					 0);
		}

		/* If we've not already sent a tool_button_?? code, do
		 * so now. Then set FIRED_BIT so it won't be resent unless
		 * the user forces FIRED_BIT off.
		 */
		if (TOOL_BUTTON_FIRED(aiptek->curSetting.toolMode) == 0) {
			input_report_key(inputdev,
					 TOOL_BUTTON(aiptek->curSetting.
						     toolMode), 1);
			aiptek->curSetting.toolMode |= TOOL_BUTTON_FIRED_BIT;
		}

		input_report_key(inputdev, macroKeyEvents[macro], 1);
		input_report_abs(inputdev, ABS_MISC,
				 1 | AIPTEK_REPORT_TOOL_UNKNOWN);
		input_sync(inputdev);
	} else {
		dbg("Unknown report %d", data[0]);
	}

	/* Jitter may occur when the user presses a button on the stlyus
	 * or the mouse. What we do to prevent that is wait 'x' milliseconds
	 * following a 'jitterable' event, which should give the hand some time
	 * stabilize itself.
	 *
	 * We just introduced aiptek->previousJitterable to carry forth the
	 * notion that jitter occurs when the button state changes from on to off:
	 * a person drawing, holding a button down is not subject to jittering.
	 * With that in mind, changing from upper button depressed to lower button
	 * WILL transition through a jitter delay.
	 */

	if (aiptek->previousJitterable != jitterable &&
	    aiptek->curSetting.jitterDelay != 0 && aiptek->inDelay != 1) {
		aiptek->endDelay = jiffies +
		    ((aiptek->curSetting.jitterDelay * HZ) / 1000);
		aiptek->inDelay = 1;
	}
	aiptek->previousJitterable = jitterable;

exit:
	retval = usb_submit_urb(urb, GFP_ATOMIC);
	if (retval != 0) {
		err("%s - usb_submit_urb failed with result %d",
		    __FUNCTION__, retval);
	}
}

/***********************************************************************
 * These are the USB id's known so far. We do not identify them to
 * specific Aiptek model numbers, because there has been overlaps,
 * use, and reuse of id's in existing models. Certain models have
 * been known to use more than one ID, indicative perhaps of
 * manufacturing revisions. In any event, we consider these 
 * IDs to not be model-specific nor unique.
 */
static const struct usb_device_id aiptek_ids[] = {
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x01)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x10)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x20)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x21)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x22)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x23)},
	{USB_DEVICE(USB_VENDOR_ID_AIPTEK, 0x24)},
	{}
};

MODULE_DEVICE_TABLE(usb, aiptek_ids);

/***********************************************************************
 * Open an instance of the tablet driver.
 */
static int aiptek_open(struct input_dev *inputdev)
{
	struct aiptek *aiptek = inputdev->private;

	if (aiptek->openCount++ > 0) {
		return 0;
	}

	aiptek->urb->dev = aiptek->usbdev;
	if (usb_submit_urb(aiptek->urb, GFP_KERNEL) != 0) {
		aiptek->openCount--;
		return -EIO;
	}

	return 0;
}

/***********************************************************************
 * Close an instance of the tablet driver.
 */
static void aiptek_close(struct input_dev *inputdev)
{
	struct aiptek *aiptek = inputdev->private;

	if (--aiptek->openCount == 0) {
		usb_kill_urb(aiptek->urb);
	}
}

/***********************************************************************
 * aiptek_set_report and aiptek_get_report() are borrowed from Linux 2.4.x, 
 * where they were known as usb_set_report and usb_get_report.
 */
static int
aiptek_set_report(struct aiptek *aiptek,
		  unsigned char report_type,
		  unsigned char report_id, void *buffer, int size)
{
	return usb_control_msg(aiptek->usbdev,
			       usb_sndctrlpipe(aiptek->usbdev, 0),
			       USB_REQ_SET_REPORT,
			       USB_TYPE_CLASS | USB_RECIP_INTERFACE |
			       USB_DIR_OUT, (report_type << 8) + report_id,
			       aiptek->ifnum, buffer, size, 5000);
}

static int
aiptek_get_report(struct aiptek *aiptek,
		  unsigned char report_type,
		  unsigned char report_id, void *buffer, int size)
{
	return usb_control_msg(aiptek->usbdev,
			       usb_rcvctrlpipe(aiptek->usbdev, 0),
			       USB_REQ_GET_REPORT,
			       USB_TYPE_CLASS | USB_RECIP_INTERFACE |
			       USB_DIR_IN, (report_type << 8) + report_id,
			       aiptek->ifnum, buffer, size, 5000);
}

/***********************************************************************
 * Send a command to the tablet.
 */
static int
aiptek_command(struct aiptek *aiptek, unsigned char command, unsigned char data)
{
	const int sizeof_buf = 3 * sizeof(u8);
	int ret;
	u8 *buf;

	buf = kmalloc(sizeof_buf, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	buf[0] = 2;
	buf[1] = command;
	buf[2] = data;

	if ((ret =
	     aiptek_set_report(aiptek, 3, 2, buf, sizeof_buf)) != sizeof_buf) {
		dbg("aiptek_program: failed, tried to send: 0x%02x 0x%02x",
		    command, data);
	}
	kfree(buf);
	return ret < 0 ? ret : 0;
}

/***********************************************************************
 * Retrieve information from the tablet. Querying info is defined as first
 * sending the {command,data} sequence as a command, followed by a wait
 * (aka, "programmaticDelay") and then a "read" request.
 */
static int
aiptek_query(struct aiptek *aiptek, unsigned char command, unsigned char data)
{
	const int sizeof_buf = 3 * sizeof(u8);
	int ret;
	u8 *buf;

	buf = kmalloc(sizeof_buf, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	buf[0] = 2;
	buf[1] = command;
	buf[2] = data;

	if (aiptek_command(aiptek, command, data) != 0) {
		kfree(buf);
		return -EIO;
	}
	msleep(aiptek->curSetting.programmableDelay);

	if ((ret =
	     aiptek_get_report(aiptek, 3, 2, buf, sizeof_buf)) != sizeof_buf) {
		dbg("aiptek_query failed: returned 0x%02x 0x%02x 0x%02x",
		    buf[0], buf[1], buf[2]);
		ret = -EIO;
	} else {
		ret = le16_to_cpu(get_unaligned((__le16 *) (buf + 1)));
	}
	kfree(buf);
	return ret;
}

/***********************************************************************
 * Program the tablet into either absolute or relative mode.
 * We also get information about the tablet's size.
 */
static int aiptek_program_tablet(struct aiptek *aiptek)
{
	int ret;
	/* Execute Resolution500LPI */
	if ((ret = aiptek_command(aiptek, 0x18, 0x04)) < 0)
		return ret;

	/* Query getModelCode */
	if ((ret = aiptek_query(aiptek, 0x02, 0x00)) < 0)
		return ret;
	aiptek->features.modelCode = ret & 0xff;

	/* Query getODMCode */
	if ((ret = aiptek_query(aiptek, 0x03, 0x00)) < 0)
		return ret;
	aiptek->features.odmCode = ret;

	/* Query getFirmwareCode */
	if ((ret = aiptek_query(aiptek, 0x04, 0x00)) < 0)
		return ret;
	aiptek->features.firmwareCode = ret;

	/* Query getXextension */
	if ((ret = aiptek_query(aiptek, 0x01, 0x00)) < 0)
		return ret;
	aiptek->inputdev.absmin[ABS_X] = 0;
	aiptek->inputdev.absmax[ABS_X] = ret - 1;

	/* Query getYextension */
	if ((ret = aiptek_query(aiptek, 0x01, 0x01)) < 0)
		return ret;
	aiptek->inputdev.absmin[ABS_Y] = 0;
	aiptek->inputdev.absmax[ABS_Y] = ret - 1;

	/* Query getPressureLevels */
	if ((ret = aiptek_query(aiptek, 0x08, 0x00)) < 0)
		return ret;
	aiptek->inputdev.absmin[ABS_PRESSURE] = 0;
	aiptek->inputdev.absmax[ABS_PRESSURE] = ret - 1;

	/* Depending on whether we are in absolute or relative mode, we will
	 * do a switchToTablet(absolute) or switchToMouse(relative) command.
	 */
	if (aiptek->curSetting.coordinateMode ==
	    AIPTEK_COORDINATE_ABSOLUTE_MODE) {
		/* Execute switchToTablet */
		if ((ret = aiptek_command(aiptek, 0x10, 0x01)) < 0) {
			return ret;
		}
	} else {
		/* Execute switchToMouse */
		if ((ret = aiptek_command(aiptek, 0x10, 0x00)) < 0) {
			return ret;
		}
	}

	/* Enable the macro keys */
	if ((ret = aiptek_command(aiptek, 0x11, 0x02)) < 0)
		return ret;
#if 0
	/* Execute FilterOn */
	if ((ret = aiptek_command(aiptek, 0x17, 0x00)) < 0)
		return ret;
#endif

	/* Execute AutoGainOn */
	if ((ret = aiptek_command(aiptek, 0x12, 0xff)) < 0)
		return ret;

	/* Reset the eventCount, so we track events from last (re)programming
	 */
	aiptek->diagnostic = AIPTEK_DIAGNOSTIC_NA;
	aiptek->eventCount = 0;

	return 0;
}

/***********************************************************************
 * Sysfs functions. Sysfs prefers that individually-tunable parameters
 * exist in their separate pseudo-files. Summary data that is immutable
 * may exist in a singular file so long as you don't define a writeable
 * interface.
 */

/***********************************************************************
 * support the 'size' file -- display support
 */
static ssize_t show_tabletSize(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "%dx%d\n",
			aiptek->inputdev.absmax[ABS_X] + 1,
			aiptek->inputdev.absmax[ABS_Y] + 1);
}

/* These structs define the sysfs files, param #1 is the name of the
 * file, param 2 is the file permissions, param 3 & 4 are to the
 * output generator and input parser routines. Absence of a routine is
 * permitted -- it only means can't either 'cat' the file, or send data
 * to it.
 */
static DEVICE_ATTR(size, S_IRUGO, show_tabletSize, NULL);

/***********************************************************************
 * support routines for the 'product_id' file
 */
static ssize_t show_tabletProductId(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "0x%04x\n",
			aiptek->inputdev.id.product);
}

static DEVICE_ATTR(product_id, S_IRUGO, show_tabletProductId, NULL);

/***********************************************************************
 * support routines for the 'vendor_id' file
 */
static ssize_t show_tabletVendorId(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "0x%04x\n", aiptek->inputdev.id.vendor);
}

static DEVICE_ATTR(vendor_id, S_IRUGO, show_tabletVendorId, NULL);

/***********************************************************************
 * support routines for the 'vendor' file
 */
static ssize_t show_tabletManufacturer(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	int retval;

	if (aiptek == NULL)
		return 0;

	retval = snprintf(buf, PAGE_SIZE, "%s\n", aiptek->usbdev->manufacturer);
	return retval;
}

static DEVICE_ATTR(vendor, S_IRUGO, show_tabletManufacturer, NULL);

/***********************************************************************
 * support routines for the 'product' file
 */
static ssize_t show_tabletProduct(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	int retval;

	if (aiptek == NULL)
		return 0;

	retval = snprintf(buf, PAGE_SIZE, "%s\n", aiptek->usbdev->product);
	return retval;
}

static DEVICE_ATTR(product, S_IRUGO, show_tabletProduct, NULL);

/***********************************************************************
 * support routines for the 'pointer_mode' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletPointerMode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.pointerMode) {
	case AIPTEK_POINTER_ONLY_STYLUS_MODE:
		s = "stylus";
		break;

	case AIPTEK_POINTER_ONLY_MOUSE_MODE:
		s = "mouse";
		break;

	case AIPTEK_POINTER_EITHER_MODE:
		s = "either";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletPointerMode(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "stylus") == 0) {
		aiptek->newSetting.pointerMode =
		    AIPTEK_POINTER_ONLY_STYLUS_MODE;
	} else if (strcmp(buf, "mouse") == 0) {
		aiptek->newSetting.pointerMode = AIPTEK_POINTER_ONLY_MOUSE_MODE;
	} else if (strcmp(buf, "either") == 0) {
		aiptek->newSetting.pointerMode = AIPTEK_POINTER_EITHER_MODE;
	}
	return count;
}

static DEVICE_ATTR(pointer_mode,
		   S_IRUGO | S_IWUGO,
		   show_tabletPointerMode, store_tabletPointerMode);

/***********************************************************************
 * support routines for the 'coordinate_mode' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletCoordinateMode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.coordinateMode) {
	case AIPTEK_COORDINATE_ABSOLUTE_MODE:
		s = "absolute";
		break;

	case AIPTEK_COORDINATE_RELATIVE_MODE:
		s = "relative";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletCoordinateMode(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "absolute") == 0) {
		aiptek->newSetting.pointerMode =
		    AIPTEK_COORDINATE_ABSOLUTE_MODE;
	} else if (strcmp(buf, "relative") == 0) {
		aiptek->newSetting.pointerMode =
		    AIPTEK_COORDINATE_RELATIVE_MODE;
	}
	return count;
}

static DEVICE_ATTR(coordinate_mode,
		   S_IRUGO | S_IWUGO,
		   show_tabletCoordinateMode, store_tabletCoordinateMode);

/***********************************************************************
 * support routines for the 'tool_mode' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletToolMode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (TOOL_BUTTON(aiptek->curSetting.toolMode)) {
	case AIPTEK_TOOL_BUTTON_MOUSE_MODE:
		s = "mouse";
		break;

	case AIPTEK_TOOL_BUTTON_ERASER_MODE:
		s = "eraser";
		break;

	case AIPTEK_TOOL_BUTTON_PENCIL_MODE:
		s = "pencil";
		break;

	case AIPTEK_TOOL_BUTTON_PEN_MODE:
		s = "pen";
		break;

	case AIPTEK_TOOL_BUTTON_BRUSH_MODE:
		s = "brush";
		break;

	case AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE:
		s = "airbrush";
		break;

	case AIPTEK_TOOL_BUTTON_LENS_MODE:
		s = "lens";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletToolMode(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "mouse") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_MOUSE_MODE;
	} else if (strcmp(buf, "eraser") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_ERASER_MODE;
	} else if (strcmp(buf, "pencil") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_PENCIL_MODE;
	} else if (strcmp(buf, "pen") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_PEN_MODE;
	} else if (strcmp(buf, "brush") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_BRUSH_MODE;
	} else if (strcmp(buf, "airbrush") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_AIRBRUSH_MODE;
	} else if (strcmp(buf, "lens") == 0) {
		aiptek->newSetting.toolMode = AIPTEK_TOOL_BUTTON_LENS_MODE;
	}

	return count;
}

static DEVICE_ATTR(tool_mode,
		   S_IRUGO | S_IWUGO,
		   show_tabletToolMode, store_tabletToolMode);

/***********************************************************************
 * support routines for the 'xtilt' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletXtilt(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (aiptek->curSetting.xTilt == AIPTEK_TILT_DISABLE) {
		return snprintf(buf, PAGE_SIZE, "disable\n");
	} else {
		return snprintf(buf, PAGE_SIZE, "%d\n",
				aiptek->curSetting.xTilt);
	}
}

static ssize_t
store_tabletXtilt(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	int x;

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "disable") == 0) {
		aiptek->newSetting.xTilt = AIPTEK_TILT_DISABLE;
	} else {
		x = (int)simple_strtol(buf, NULL, 10);
		if (x >= AIPTEK_TILT_MIN && x <= AIPTEK_TILT_MAX) {
			aiptek->newSetting.xTilt = x;
		}
	}
	return count;
}

static DEVICE_ATTR(xtilt,
		   S_IRUGO | S_IWUGO, show_tabletXtilt, store_tabletXtilt);

/***********************************************************************
 * support routines for the 'ytilt' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletYtilt(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (aiptek->curSetting.yTilt == AIPTEK_TILT_DISABLE) {
		return snprintf(buf, PAGE_SIZE, "disable\n");
	} else {
		return snprintf(buf, PAGE_SIZE, "%d\n",
				aiptek->curSetting.yTilt);
	}
}

static ssize_t
store_tabletYtilt(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	int y;

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "disable") == 0) {
		aiptek->newSetting.yTilt = AIPTEK_TILT_DISABLE;
	} else {
		y = (int)simple_strtol(buf, NULL, 10);
		if (y >= AIPTEK_TILT_MIN && y <= AIPTEK_TILT_MAX) {
			aiptek->newSetting.yTilt = y;
		}
	}
	return count;
}

static DEVICE_ATTR(ytilt,
		   S_IRUGO | S_IWUGO, show_tabletYtilt, store_tabletYtilt);

/***********************************************************************
 * support routines for the 'jitter' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletJitterDelay(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "%d\n", aiptek->curSetting.jitterDelay);
}

static ssize_t
store_tabletJitterDelay(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	aiptek->newSetting.jitterDelay = (int)simple_strtol(buf, NULL, 10);
	return count;
}

static DEVICE_ATTR(jitter,
		   S_IRUGO | S_IWUGO,
		   show_tabletJitterDelay, store_tabletJitterDelay);

/***********************************************************************
 * support routines for the 'delay' file. Note that this file
 * both displays current setting and allows reprogramming.
 */
static ssize_t show_tabletProgrammableDelay(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "%d\n",
			aiptek->curSetting.programmableDelay);
}

static ssize_t
store_tabletProgrammableDelay(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	aiptek->newSetting.programmableDelay = (int)simple_strtol(buf, NULL, 10);
	return count;
}

static DEVICE_ATTR(delay,
		   S_IRUGO | S_IWUGO,
		   show_tabletProgrammableDelay, store_tabletProgrammableDelay);

/***********************************************************************
 * support routines for the 'input_path' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_tabletInputDevice(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "/dev/input/%s\n",
			aiptek->features.inputPath);
}

static DEVICE_ATTR(input_path, S_IRUGO, show_tabletInputDevice, NULL);

/***********************************************************************
 * support routines for the 'event_count' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_tabletEventsReceived(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "%ld\n", aiptek->eventCount);
}

static DEVICE_ATTR(event_count, S_IRUGO, show_tabletEventsReceived, NULL);

/***********************************************************************
 * support routines for the 'diagnostic' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_tabletDiagnosticMessage(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *retMsg;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->diagnostic) {
	case AIPTEK_DIAGNOSTIC_NA:
		retMsg = "no errors\n";
		break;

	case AIPTEK_DIAGNOSTIC_SENDING_RELATIVE_IN_ABSOLUTE:
		retMsg = "Error: receiving relative reports\n";
		break;

	case AIPTEK_DIAGNOSTIC_SENDING_ABSOLUTE_IN_RELATIVE:
		retMsg = "Error: receiving absolute reports\n";
		break;

	case AIPTEK_DIAGNOSTIC_TOOL_DISALLOWED:
		if (aiptek->curSetting.pointerMode ==
		    AIPTEK_POINTER_ONLY_MOUSE_MODE) {
			retMsg = "Error: receiving stylus reports\n";
		} else {
			retMsg = "Error: receiving mouse reports\n";
		}
		break;

	default:
		return 0;
	}
	return snprintf(buf, PAGE_SIZE, retMsg);
}

static DEVICE_ATTR(diagnostic, S_IRUGO, show_tabletDiagnosticMessage, NULL);

/***********************************************************************
 * support routines for the 'stylus_upper' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletStylusUpper(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.stylusButtonUpper) {
	case AIPTEK_STYLUS_UPPER_BUTTON:
		s = "upper";
		break;

	case AIPTEK_STYLUS_LOWER_BUTTON:
		s = "lower";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletStylusUpper(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "upper") == 0) {
		aiptek->newSetting.stylusButtonUpper =
		    AIPTEK_STYLUS_UPPER_BUTTON;
	} else if (strcmp(buf, "lower") == 0) {
		aiptek->newSetting.stylusButtonUpper =
		    AIPTEK_STYLUS_LOWER_BUTTON;
	}
	return count;
}

static DEVICE_ATTR(stylus_upper,
		   S_IRUGO | S_IWUGO,
		   show_tabletStylusUpper, store_tabletStylusUpper);

/***********************************************************************
 * support routines for the 'stylus_lower' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletStylusLower(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.stylusButtonLower) {
	case AIPTEK_STYLUS_UPPER_BUTTON:
		s = "upper";
		break;

	case AIPTEK_STYLUS_LOWER_BUTTON:
		s = "lower";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletStylusLower(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "upper") == 0) {
		aiptek->newSetting.stylusButtonLower =
		    AIPTEK_STYLUS_UPPER_BUTTON;
	} else if (strcmp(buf, "lower") == 0) {
		aiptek->newSetting.stylusButtonLower =
		    AIPTEK_STYLUS_LOWER_BUTTON;
	}
	return count;
}

static DEVICE_ATTR(stylus_lower,
		   S_IRUGO | S_IWUGO,
		   show_tabletStylusLower, store_tabletStylusLower);

/***********************************************************************
 * support routines for the 'mouse_left' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletMouseLeft(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.mouseButtonLeft) {
	case AIPTEK_MOUSE_LEFT_BUTTON:
		s = "left";
		break;

	case AIPTEK_MOUSE_MIDDLE_BUTTON:
		s = "middle";
		break;

	case AIPTEK_MOUSE_RIGHT_BUTTON:
		s = "right";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletMouseLeft(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "left") == 0) {
		aiptek->newSetting.mouseButtonLeft = AIPTEK_MOUSE_LEFT_BUTTON;
	} else if (strcmp(buf, "middle") == 0) {
		aiptek->newSetting.mouseButtonLeft = AIPTEK_MOUSE_MIDDLE_BUTTON;
	} else if (strcmp(buf, "right") == 0) {
		aiptek->newSetting.mouseButtonLeft = AIPTEK_MOUSE_RIGHT_BUTTON;
	}
	return count;
}

static DEVICE_ATTR(mouse_left,
		   S_IRUGO | S_IWUGO,
		   show_tabletMouseLeft, store_tabletMouseLeft);

/***********************************************************************
 * support routines for the 'mouse_middle' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletMouseMiddle(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.mouseButtonMiddle) {
	case AIPTEK_MOUSE_LEFT_BUTTON:
		s = "left";
		break;

	case AIPTEK_MOUSE_MIDDLE_BUTTON:
		s = "middle";
		break;

	case AIPTEK_MOUSE_RIGHT_BUTTON:
		s = "right";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletMouseMiddle(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "left") == 0) {
		aiptek->newSetting.mouseButtonMiddle = AIPTEK_MOUSE_LEFT_BUTTON;
	} else if (strcmp(buf, "middle") == 0) {
		aiptek->newSetting.mouseButtonMiddle =
		    AIPTEK_MOUSE_MIDDLE_BUTTON;
	} else if (strcmp(buf, "right") == 0) {
		aiptek->newSetting.mouseButtonMiddle =
		    AIPTEK_MOUSE_RIGHT_BUTTON;
	}
	return count;
}

static DEVICE_ATTR(mouse_middle,
		   S_IRUGO | S_IWUGO,
		   show_tabletMouseMiddle, store_tabletMouseMiddle);

/***********************************************************************
 * support routines for the 'mouse_right' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletMouseRight(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);
	char *s;

	if (aiptek == NULL)
		return 0;

	switch (aiptek->curSetting.mouseButtonRight) {
	case AIPTEK_MOUSE_LEFT_BUTTON:
		s = "left";
		break;

	case AIPTEK_MOUSE_MIDDLE_BUTTON:
		s = "middle";
		break;

	case AIPTEK_MOUSE_RIGHT_BUTTON:
		s = "right";
		break;

	default:
		s = "unknown";
		break;
	}
	return snprintf(buf, PAGE_SIZE, "%s\n", s);
}

static ssize_t
store_tabletMouseRight(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (strcmp(buf, "left") == 0) {
		aiptek->newSetting.mouseButtonRight = AIPTEK_MOUSE_LEFT_BUTTON;
	} else if (strcmp(buf, "middle") == 0) {
		aiptek->newSetting.mouseButtonRight =
		    AIPTEK_MOUSE_MIDDLE_BUTTON;
	} else if (strcmp(buf, "right") == 0) {
		aiptek->newSetting.mouseButtonRight = AIPTEK_MOUSE_RIGHT_BUTTON;
	}
	return count;
}

static DEVICE_ATTR(mouse_right,
		   S_IRUGO | S_IWUGO,
		   show_tabletMouseRight, store_tabletMouseRight);

/***********************************************************************
 * support routines for the 'wheel' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletWheel(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	if (aiptek->curSetting.wheel == AIPTEK_WHEEL_DISABLE) {
		return snprintf(buf, PAGE_SIZE, "disable\n");
	} else {
		return snprintf(buf, PAGE_SIZE, "%d\n",
				aiptek->curSetting.wheel);
	}
}

static ssize_t
store_tabletWheel(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	aiptek->newSetting.wheel = (int)simple_strtol(buf, NULL, 10);
	return count;
}

static DEVICE_ATTR(wheel,
		   S_IRUGO | S_IWUGO, show_tabletWheel, store_tabletWheel);

/***********************************************************************
 * support routines for the 'execute' file. Note that this file
 * both displays current setting and allows for setting changing.
 */
static ssize_t show_tabletExecute(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	/* There is nothing useful to display, so a one-line manual
	 * is in order...
	 */
	return snprintf(buf, PAGE_SIZE,
			"Write anything to this file to program your tablet.\n");
}

static ssize_t
store_tabletExecute(struct device *dev, const char *buf, size_t count)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	/* We do not care what you write to this file. Merely the action
	 * of writing to this file triggers a tablet reprogramming.
	 */
	memcpy(&aiptek->curSetting, &aiptek->newSetting,
	       sizeof(struct aiptek_settings));

	if (aiptek_program_tablet(aiptek) < 0)
		return -EIO;

	return count;
}

static DEVICE_ATTR(execute,
		   S_IRUGO | S_IWUGO, show_tabletExecute, store_tabletExecute);

/***********************************************************************
 * support routines for the 'odm_code' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_tabletODMCode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "0x%04x\n", aiptek->features.odmCode);
}

static DEVICE_ATTR(odm_code, S_IRUGO, show_tabletODMCode, NULL);

/***********************************************************************
 * support routines for the 'model_code' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_tabletModelCode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "0x%04x\n", aiptek->features.modelCode);
}

static DEVICE_ATTR(model_code, S_IRUGO, show_tabletModelCode, NULL);

/***********************************************************************
 * support routines for the 'firmware_code' file. Note that this file
 * only displays current setting.
 */
static ssize_t show_firmwareCode(struct device *dev, char *buf)
{
	struct aiptek *aiptek = dev_get_drvdata(dev);

	if (aiptek == NULL)
		return 0;

	return snprintf(buf, PAGE_SIZE, "%04x\n",
			aiptek->features.firmwareCode);
}

static DEVICE_ATTR(firmware_code, S_IRUGO, show_firmwareCode, NULL);

/***********************************************************************
 * This routine removes all existing sysfs files managed by this device
 * driver.
 */
static void aiptek_delete_files(struct device *dev)
{
	device_remove_file(dev, &dev_attr_size);
	device_remove_file(dev, &dev_attr_product_id);
	device_remove_file(dev, &dev_attr_vendor_id);
	device_remove_file(dev, &dev_attr_vendor);
	device_remove_file(dev, &dev_attr_product);
	device_remove_file(dev, &dev_attr_pointer_mode);
	device_remove_file(dev, &dev_attr_coordinate_mode);
	device_remove_file(dev, &dev_attr_tool_mode);
	device_remove_file(dev, &dev_attr_xtilt);
	device_remove_file(dev, &dev_attr_ytilt);
	device_remove_file(dev, &dev_attr_jitter);
	device_remove_file(dev, &dev_attr_delay);
	device_remove_file(dev, &dev_attr_input_path);
	device_remove_file(dev, &dev_attr_event_count);
	device_remove_file(dev, &dev_attr_diagnostic);
	device_remove_file(dev, &dev_attr_odm_code);
	device_remove_file(dev, &dev_attr_model_code);
	device_remove_file(dev, &dev_attr_firmware_code);
	device_remove_file(dev, &dev_attr_stylus_lower);
	device_remove_file(dev, &dev_attr_stylus_upper);
	device_remove_file(dev, &dev_attr_mouse_left);
	device_remove_file(dev, &dev_attr_mouse_middle);
	device_remove_file(dev, &dev_attr_mouse_right);
	device_remove_file(dev, &dev_attr_wheel);
	device_remove_file(dev, &dev_attr_execute);
}

/***********************************************************************
 * This routine creates the sysfs files managed by this device
 * driver.
 */
static int aiptek_add_files(struct device *dev)
{
	int ret;

	if ((ret = device_create_file(dev, &dev_attr_size)) ||
	    (ret = device_create_file(dev, &dev_attr_product_id)) ||
	    (ret = device_create_file(dev, &dev_attr_vendor_id)) ||
	    (ret = device_create_file(dev, &dev_attr_vendor)) ||
	    (ret = device_create_file(dev, &dev_attr_product)) ||
	    (ret = device_create_file(dev, &dev_attr_pointer_mode)) ||
	    (ret = device_create_file(dev, &dev_attr_coordinate_mode)) ||
	    (ret = device_create_file(dev, &dev_attr_tool_mode)) ||
	    (ret = device_create_file(dev, &dev_attr_xtilt)) ||
	    (ret = device_create_file(dev, &dev_attr_ytilt)) ||
	    (ret = device_create_file(dev, &dev_attr_jitter)) ||
	    (ret = device_create_file(dev, &dev_attr_delay)) ||
	    (ret = device_create_file(dev, &dev_attr_input_path)) ||
	    (ret = device_create_file(dev, &dev_attr_event_count)) ||
	    (ret = device_create_file(dev, &dev_attr_diagnostic)) ||
	    (ret = device_create_file(dev, &dev_attr_odm_code)) ||
	    (ret = device_create_file(dev, &dev_attr_model_code)) ||
	    (ret = device_create_file(dev, &dev_attr_firmware_code)) ||
	    (ret = device_create_file(dev, &dev_attr_stylus_lower)) ||
	    (ret = device_create_file(dev, &dev_attr_stylus_upper)) ||
	    (ret = device_create_file(dev, &dev_attr_mouse_left)) ||
	    (ret = device_create_file(dev, &dev_attr_mouse_middle)) ||
	    (ret = device_create_file(dev, &dev_attr_mouse_right)) ||
	    (ret = device_create_file(dev, &dev_attr_wheel)) ||
	    (ret = device_create_file(dev, &dev_attr_execute))) {
		err("aiptek: killing own sysfs device files\n");
		aiptek_delete_files(dev);
	}
	return ret;
}

/***********************************************************************
 * This routine is called when a tablet has been identified. It basically
 * sets up the tablet and the driver's internal structures.
 */
static int
aiptek_probe(struct usb_interface *intf, const struct usb_device_id *id)
{
	struct usb_device *usbdev = interface_to_usbdev(intf);
	struct usb_endpoint_descriptor *endpoint;
	struct aiptek *aiptek;
	struct input_dev *inputdev;
	struct input_handle *inputhandle;
	struct list_head *node, *next;
	char path[64 + 1];
	int i;
	int speeds[] = { 0,
		AIPTEK_PROGRAMMABLE_DELAY_50,
		AIPTEK_PROGRAMMABLE_DELAY_400,
		AIPTEK_PROGRAMMABLE_DELAY_25,
		AIPTEK_PROGRAMMABLE_DELAY_100,
		AIPTEK_PROGRAMMABLE_DELAY_200,
		AIPTEK_PROGRAMMABLE_DELAY_300
	};

	/* programmableDelay is where the command-line specified
	 * delay is kept. We make it the first element of speeds[],
	 * so therefore, your override speed is tried first, then the
	 * remainder. Note that the default value of 400ms will be tried
	 * if you do not specify any command line parameter.
	 */
	speeds[0] = programmableDelay;

	if ((aiptek = kmalloc(sizeof(struct aiptek), GFP_KERNEL)) == NULL)
		return -ENOMEM;
	memset(aiptek, 0, sizeof(struct aiptek));

	aiptek->data = usb_buffer_alloc(usbdev, AIPTEK_PACKET_LENGTH,
					SLAB_ATOMIC, &aiptek->data_dma);
	if (aiptek->data == NULL) {
		kfree(aiptek);
		return -ENOMEM;
	}

	aiptek->urb = usb_alloc_urb(0, GFP_KERNEL);
	if (aiptek->urb == NULL) {
		usb_buffer_free(usbdev, AIPTEK_PACKET_LENGTH, aiptek->data,
				aiptek->data_dma);
		kfree(aiptek);
		return -ENOMEM;
	}

	/* Set up the curSettings struct. Said struct contains the current
	 * programmable parameters. The newSetting struct contains changes
	 * the user makes to the settings via the sysfs interface. Those
	 * changes are not "committed" to curSettings until the user
	 * writes to the sysfs/.../execute file.
	 */
	aiptek->curSetting.pointerMode = AIPTEK_POINTER_EITHER_MODE;
	aiptek->curSetting.coordinateMode = AIPTEK_COORDINATE_ABSOLUTE_MODE;
	aiptek->curSetting.toolMode = AIPTEK_TOOL_BUTTON_PEN_MODE;
	aiptek->curSetting.xTilt = AIPTEK_TILT_DISABLE;
	aiptek->curSetting.yTilt = AIPTEK_TILT_DISABLE;
	aiptek->curSetting.mouseButtonLeft = AIPTEK_MOUSE_LEFT_BUTTON;
	aiptek->curSetting.mouseButtonMiddle = AIPTEK_MOUSE_MIDDLE_BUTTON;
	aiptek->curSetting.mouseButtonRight = AIPTEK_MOUSE_RIGHT_BUTTON;
	aiptek->curSetting.stylusButtonUpper = AIPTEK_STYLUS_UPPER_BUTTON;
	aiptek->curSetting.stylusButtonLower = AIPTEK_STYLUS_LOWER_BUTTON;
	aiptek->curSetting.jitterDelay = jitterDelay;
	aiptek->curSetting.programmableDelay = programmableDelay;

	/* Both structs should have equivalent settings
	 */
	memcpy(&aiptek->newSetting, &aiptek->curSetting,
	       sizeof(struct aiptek_settings));

	/* Now program the capacities of the tablet, in terms of being
	 * an input device.
	 */
	aiptek->inputdev.evbit[0] |= BIT(EV_KEY)
	    | BIT(EV_ABS)
	    | BIT(EV_REL)
	    | BIT(EV_MSC);

	aiptek->inputdev.absbit[0] |=
	    (BIT(ABS_X) |
	     BIT(ABS_Y) |
	     BIT(ABS_PRESSURE) |
	     BIT(ABS_TILT_X) |
	     BIT(ABS_TILT_Y) | BIT(ABS_WHEEL) | BIT(ABS_MISC));

	aiptek->inputdev.relbit[0] |=
	    (BIT(REL_X) | BIT(REL_Y) | BIT(REL_WHEEL) | BIT(REL_MISC));

	aiptek->inputdev.keybit[LONG(BTN_LEFT)] |=
	    (BIT(BTN_LEFT) | BIT(BTN_RIGHT) | BIT(BTN_MIDDLE));

	aiptek->inputdev.keybit[LONG(BTN_DIGI)] |=
	    (BIT(BTN_TOOL_PEN) |
	     BIT(BTN_TOOL_RUBBER) |
	     BIT(BTN_TOOL_PENCIL) |
	     BIT(BTN_TOOL_AIRBRUSH) |
	     BIT(BTN_TOOL_BRUSH) |
	     BIT(BTN_TOOL_MOUSE) |
	     BIT(BTN_TOOL_LENS) |
	     BIT(BTN_TOUCH) | BIT(BTN_STYLUS) | BIT(BTN_STYLUS2));

	aiptek->inputdev.mscbit[0] = BIT(MSC_SERIAL);

	/* Programming the tablet macro keys needs to be done with a for loop
	 * as the keycodes are discontiguous.
	 */
	for (i = 0; i < sizeof(macroKeyEvents) / sizeof(macroKeyEvents[0]); ++i)
		set_bit(macroKeyEvents[i], aiptek->inputdev.keybit);

	/* Set up client data, pointers to open and close routines
	 * for the input device.
	 */
	aiptek->inputdev.private = aiptek;
	aiptek->inputdev.open = aiptek_open;
	aiptek->inputdev.close = aiptek_close;

	/* Determine the usb devices' physical path.
	 * Asketh not why we always pretend we're using "../input0",
	 * but I suspect this will have to be refactored one
	 * day if a single USB device can be a keyboard & a mouse
	 * & a tablet, and the inputX number actually will tell
	 * us something...
	 */
	if (usb_make_path(usbdev, path, 64) > 0)
		sprintf(aiptek->features.usbPath, "%s/input0", path);

	/* Program the input device coordinate capacities. We do not yet
	 * know what maximum X, Y, and Z values are, so we're putting fake
	 * values in. Later, we'll ask the tablet to put in the correct
	 * values.
	 */
	aiptek->inputdev.absmin[ABS_X] = 0;
	aiptek->inputdev.absmax[ABS_X] = 2999;
	aiptek->inputdev.absmin[ABS_Y] = 0;
	aiptek->inputdev.absmax[ABS_Y] = 2249;
	aiptek->inputdev.absmin[ABS_PRESSURE] = 0;
	aiptek->inputdev.absmax[ABS_PRESSURE] = 511;
	aiptek->inputdev.absmin[ABS_TILT_X] = AIPTEK_TILT_MIN;
	aiptek->inputdev.absmax[ABS_TILT_X] = AIPTEK_TILT_MAX;
	aiptek->inputdev.absmin[ABS_TILT_Y] = AIPTEK_TILT_MIN;
	aiptek->inputdev.absmax[ABS_TILT_Y] = AIPTEK_TILT_MAX;
	aiptek->inputdev.absmin[ABS_WHEEL] = AIPTEK_WHEEL_MIN;
	aiptek->inputdev.absmax[ABS_WHEEL] = AIPTEK_WHEEL_MAX - 1;
	aiptek->inputdev.absfuzz[ABS_X] = 0;
	aiptek->inputdev.absfuzz[ABS_Y] = 0;
	aiptek->inputdev.absfuzz[ABS_PRESSURE] = 0;
	aiptek->inputdev.absfuzz[ABS_TILT_X] = 0;
	aiptek->inputdev.absfuzz[ABS_TILT_Y] = 0;
	aiptek->inputdev.absfuzz[ABS_WHEEL] = 0;
	aiptek->inputdev.absflat[ABS_X] = 0;
	aiptek->inputdev.absflat[ABS_Y] = 0;
	aiptek->inputdev.absflat[ABS_PRESSURE] = 0;
	aiptek->inputdev.absflat[ABS_TILT_X] = 0;
	aiptek->inputdev.absflat[ABS_TILT_Y] = 0;
	aiptek->inputdev.absflat[ABS_WHEEL] = 0;
	aiptek->inputdev.name = "Aiptek";
	aiptek->inputdev.phys = aiptek->features.usbPath;
	aiptek->inputdev.id.bustype = BUS_USB;
	aiptek->inputdev.id.vendor = le16_to_cpu(usbdev->descriptor.idVendor);
	aiptek->inputdev.id.product = le16_to_cpu(usbdev->descriptor.idProduct);
	aiptek->inputdev.id.version = le16_to_cpu(usbdev->descriptor.bcdDevice);

	aiptek->usbdev = usbdev;
	aiptek->ifnum = intf->altsetting[0].desc.bInterfaceNumber;
	aiptek->inDelay = 0;
	aiptek->endDelay = 0;
	aiptek->previousJitterable = 0;

	endpoint = &intf->altsetting[0].endpoint[0].desc;

	/* Go set up our URB, which is called when the tablet receives
	 * input.
	 */
	usb_fill_int_urb(aiptek->urb,
			 aiptek->usbdev,
			 usb_rcvintpipe(aiptek->usbdev,
					endpoint->bEndpointAddress),
			 aiptek->data, 8, aiptek_irq, aiptek,
			 endpoint->bInterval);

	aiptek->urb->transfer_dma = aiptek->data_dma;
	aiptek->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;

	/* Register the tablet as an Input Device
	 */
	input_register_device(&aiptek->inputdev);

	/* We now will look for the evdev device which is mapped to
	 * the tablet. The partial name is kept in the link list of
	 * input_handles associated with this input device.
	 * What identifies an evdev input_handler is that it begins
	 * with 'event', continues with a digit, and that in turn
	 * is mapped to /{devfs}/input/eventN.
	 */
	inputdev = &aiptek->inputdev;
	list_for_each_safe(node, next, &inputdev->h_list) {
		inputhandle = to_handle(node);
		if (strncmp(inputhandle->name, "event", 5) == 0) {
			strcpy(aiptek->features.inputPath, inputhandle->name);
			break;
		}
	}

	info("input: Aiptek on %s (%s)\n", path, aiptek->features.inputPath);

	/* Program the tablet. This sets the tablet up in the mode
	 * specified in newSetting, and also queries the tablet's
	 * physical capacities.
	 *
	 * Sanity check: if a tablet doesn't like the slow programmatic
	 * delay, we often get sizes of 0x0. Let's use that as an indicator
	 * to try faster delays, up to 25 ms. If that logic fails, well, you'll
	 * have to explain to us how your tablet thinks it's 0x0, and yet that's
	 * not an error :-)
	 */

	for (i = 0; i < sizeof(speeds) / sizeof(speeds[0]); ++i) {
		aiptek->curSetting.programmableDelay = speeds[i];
		(void)aiptek_program_tablet(aiptek);
		if (aiptek->inputdev.absmax[ABS_X] > 0) {
			info("input: Aiptek using %d ms programming speed\n",
			     aiptek->curSetting.programmableDelay);
			break;
		}
	}

	/* Associate this driver's struct with the usb interface.
	 */
	usb_set_intfdata(intf, aiptek);

	/* Set up the sysfs files
	 */
	aiptek_add_files(&intf->dev);

	/* Make sure the evdev module is loaded. Assuming evdev IS a module :-)
	 */
	if (request_module("evdev") != 0)
		info("aiptek: error loading 'evdev' module");

	return 0;
}

/* Forward declaration */
static void aiptek_disconnect(struct usb_interface *intf);

static struct usb_driver aiptek_driver = {
	.owner = THIS_MODULE,
	.name = "aiptek",
	.probe = aiptek_probe,
	.disconnect = aiptek_disconnect,
	.id_table = aiptek_ids,
};

/***********************************************************************
 * Deal with tablet disconnecting from the system.
 */
static void aiptek_disconnect(struct usb_interface *intf)
{
	struct aiptek *aiptek = usb_get_intfdata(intf);

	/* Disassociate driver's struct with usb interface
	 */
	usb_set_intfdata(intf, NULL);
	if (aiptek != NULL) {
		/* Free & unhook everything from the system.
		 */
		usb_kill_urb(aiptek->urb);
		input_unregister_device(&aiptek->inputdev);
		aiptek_delete_files(&intf->dev);
		usb_free_urb(aiptek->urb);
		usb_buffer_free(interface_to_usbdev(intf),
				AIPTEK_PACKET_LENGTH,
				aiptek->data, aiptek->data_dma);
		kfree(aiptek);
		aiptek = NULL;
	}
}

static int __init aiptek_init(void)
{
	int result = usb_register(&aiptek_driver);
	if (result == 0) {
		info(DRIVER_VERSION ": " DRIVER_AUTHOR);
		info(DRIVER_DESC);
	}
	return result;
}

static void __exit aiptek_exit(void)
{
	usb_deregister(&aiptek_driver);
}

MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");

module_param(programmableDelay, int, 0);
MODULE_PARM_DESC(programmableDelay, "delay used during tablet programming");
module_param(jitterDelay, int, 0);
MODULE_PARM_DESC(jitterDelay, "stylus/mouse settlement delay");

module_init(aiptek_init);
module_exit(aiptek_exit);