[PATCH] sky2: fix ram buffer for Yukon FE rev 2
Fix problems with Yukon FE rev 2 chipset. Don't cut and paste bugs in from
sk98lin driver. Change how the ram buffer is divided up, and make the math
clearer. Also, set the thresholds where rx takes precedence. The threshold
values are just guesses at this point, it might be worth tuning them later.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index f68ccfb..178249a 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -625,13 +625,16 @@
}
-static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, size_t len)
+/* Assign Ram Buffer allocation.
+ * start and end are in units of 4k bytes
+ * ram registers are in units of 64bit words
+ */
+static void sky2_ramset(struct sky2_hw *hw, u16 q, u8 startk, u8 endk)
{
- u32 end;
+ u32 start, end;
- start /= 8;
- len /= 8;
- end = start + len - 1;
+ start = startk * 4096/8;
+ end = (endk * 4096/8) - 1;
sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR);
sky2_write32(hw, RB_ADDR(q, RB_START), start);
@@ -640,14 +643,19 @@
sky2_write32(hw, RB_ADDR(q, RB_RP), start);
if (q == Q_R1 || q == Q_R2) {
- u32 rxup, rxlo;
+ u32 space = (endk - startk) * 4096/8;
+ u32 tp = space - space/4;
- rxlo = len/2;
- rxup = rxlo + len/4;
+ /* On receive queue's set the thresholds
+ * give receiver priority when > 3/4 full
+ * send pause when down to 2K
+ */
+ sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp);
+ sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2);
- /* Set thresholds on receive queue's */
- sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), rxup);
- sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), rxlo);
+ tp = space - 2048/8;
+ sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp);
+ sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4);
} else {
/* Enable store & forward on Tx queue's because
* Tx FIFO is only 1K on Yukon
@@ -1002,19 +1010,19 @@
sky2_mac_init(hw, port);
- /* Configure RAM buffers */
- if (hw->chip_id == CHIP_ID_YUKON_FE ||
- (hw->chip_id == CHIP_ID_YUKON_EC && hw->chip_rev == 2))
- ramsize = 4096;
- else {
- u8 e0 = sky2_read8(hw, B2_E_0);
- ramsize = (e0 == 0) ? (128 * 1024) : (e0 * 4096);
- }
+ /* Determine available ram buffer space (in 4K blocks).
+ * Note: not sure about the FE setting below yet
+ */
+ if (hw->chip_id == CHIP_ID_YUKON_FE)
+ ramsize = 4;
+ else
+ ramsize = sky2_read8(hw, B2_E_0);
- /* 2/3 for Rx */
- rxspace = (2 * ramsize) / 3;
+ /* Give transmitter one third (rounded up) */
+ rxspace = ramsize - (ramsize + 2) / 3;
+
sky2_ramset(hw, rxqaddr[port], 0, rxspace);
- sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace);
+ sky2_ramset(hw, txqaddr[port], rxspace, ramsize);
/* Make sure SyncQ is disabled */
sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL),
