/*
 * PHYTEC phyCORE-LPC3250 board
 *
 * Copyright 2012 Roland Stigge <stigge@antcom.de>
 *
 * The code contained herein is licensed under the GNU General Public
 * License. You may obtain a copy of the GNU General Public License
 * Version 2 or later at the following locations:
 *
 * http://www.opensource.org/licenses/gpl-license.html
 * http://www.gnu.org/copyleft/gpl.html
 */

/dts-v1/;
/include/ "lpc32xx.dtsi"

/ {
	model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
	compatible = "phytec,phy3250", "nxp,lpc3250";
	#address-cells = <1>;
	#size-cells = <1>;

	memory {
		device_type = "memory";
		reg = <0 0x4000000>;
	};

	ahb {
		mac: ethernet@31060000 {
			phy-mode = "rmii";
			use-iram;
		};

		/* Here, choose exactly one from: ohci, usbd */
		ohci@31020000 {
			transceiver = <&isp1301>;
			status = "okay";
		};

/*
		usbd@31020000 {
			transceiver = <&isp1301>;
			status = "okay";
		};
*/

		clcd@31040000 {
			status = "okay";
		};

		/* 64MB Flash via SLC NAND controller */
		slc: flash@20020000 {
			status = "okay";
			#address-cells = <1>;
			#size-cells = <1>;

			mtd0@00000000 {
				label = "phy3250-boot";
				reg = <0x00000000 0x00064000>;
				read-only;
			};

			mtd1@00064000 {
				label = "phy3250-uboot";
				reg = <0x00064000 0x00190000>;
				read-only;
			};

			mtd2@001f4000 {
				label = "phy3250-ubt-prms";
				reg = <0x001f4000 0x00010000>;
			};

			mtd3@00204000 {
				label = "phy3250-kernel";
				reg = <0x00204000 0x00400000>;
			};

			mtd4@00604000 {
				label = "phy3250-rootfs";
				reg = <0x00604000 0x039fc000>;
			};
		};

		apb {
			i2c1: i2c@400A0000 {
				clock-frequency = <100000>;

				pcf8563: rtc@51 {
					compatible = "nxp,pcf8563";
					reg = <0x51>;
				};

				uda1380: uda1380@18 {
					compatible = "nxp,uda1380";
					reg = <0x18>;
					power-gpio = <&gpio 0x59 0>;
					reset-gpio = <&gpio 0x51 0>;
					dac-clk = "wspll";
				};
			};

			i2c2: i2c@400A8000 {
				clock-frequency = <100000>;
			};

			i2cusb: i2c@31020300 {
				clock-frequency = <100000>;

				isp1301: usb-transceiver@2c {
					compatible = "nxp,isp1301";
					reg = <0x2c>;
				};
			};

			ssp0: ssp@20084000 {
				eeprom: at25@0 {
					compatible = "atmel,at25";
				};
			};
		};

		fab {
			tsc@40048000 {
				status = "okay";
			};
		};
	};

	leds {
		compatible = "gpio-leds";

		led0 {
			gpios = <&gpio 5 1 1>; /* GPO_P3 1, GPIO 80, active low */
			linux,default-trigger = "heartbeat";
			default-state = "off";
		};

		led1 {
			gpios = <&gpio 5 14 1>; /* GPO_P3 14, GPIO 93, active low */
			linux,default-trigger = "timer";
			default-state = "off";
		};
	};
};