libata: improve SATA PHY speed down logic
sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus. SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.
This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 5718c24..c325b7a 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -2389,21 +2389,35 @@
u32 sstatus, spd, mask;
int rc, highbit;
+ if (!sata_scr_valid(ap))
+ return -EOPNOTSUPP;
+
+ /* If SCR can be read, use it to determine the current SPD.
+ * If not, use cached value in ap->sata_spd.
+ */
rc = sata_scr_read(ap, SCR_STATUS, &sstatus);
- if (rc)
- return rc;
+ if (rc == 0)
+ spd = (sstatus >> 4) & 0xf;
+ else
+ spd = ap->sata_spd;
mask = ap->sata_spd_limit;
if (mask <= 1)
return -EINVAL;
+
+ /* unconditionally mask off the highest bit */
highbit = fls(mask) - 1;
mask &= ~(1 << highbit);
- spd = (sstatus >> 4) & 0xf;
- if (spd <= 1)
- return -EINVAL;
- spd--;
- mask &= (1 << spd) - 1;
+ /* Mask off all speeds higher than or equal to the current
+ * one. Force 1.5Gbps if current SPD is not available.
+ */
+ if (spd > 1)
+ mask &= (1 << (spd - 1)) - 1;
+ else
+ mask &= 1;
+
+ /* were we already at the bottom? */
if (!mask)
return -EINVAL;
@@ -5995,6 +6009,7 @@
/* SATA spd limit is bound to the first device */
ap->sata_spd_limit = ap->hw_sata_spd_limit;
+ ap->sata_spd = 0;
/* High bits of dev->flags are used to record warm plug
* requests which occur asynchronously. Synchronize using
diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index 19f9947..183eaf4 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -1799,12 +1799,18 @@
}
if (rc == 0) {
+ u32 sstatus;
+
/* After the reset, the device state is PIO 0 and the
* controller state is undefined. Record the mode.
*/
for (i = 0; i < ATA_MAX_DEVICES; i++)
ap->device[i].pio_mode = XFER_PIO_0;
+ /* record current link speed */
+ if (sata_scr_read(ap, SCR_STATUS, &sstatus) == 0)
+ ap->sata_spd = (sstatus >> 4) & 0xf;
+
if (postreset)
postreset(ap, classes);
